Magnasonic 167820 User manual

Brand: Magnasonic

Model: 167820

Category: Remote controls

Type: User manual

This manual is also suitable for

Remote Control

User Guide

Remote Control

User Guide

SAT

Table of Contents

Quick Setup

Confirm Your Receiver Model ...............................................S-1

Install Your Selected Key.......................................................S-2

Insert the Batteries.................................................................S-2

Making the Remote Work with Your Receiver .......................S-3

Program the Remote to Control Your TV...............................S-4

Programming the Recover Button for TV2 Operation............S-5

Placing Your Remote in Limited Mode...................................S-6

Operation

If You Lose Your Picture ........................................................S-6

SAT Mode..............................................................................S-7

TV Mode................................................................................S-8

VCR Mode.............................................................................S-9

Remote Control Overview......................................................... 1

Using the Guide........................................................................1

Remote Control Modes............................................................. 1

How the Remote Communicates..............................................2

Programming for Other Equipment...........................................2

Combination Equipment (for example, TV/VCR)...................... 2

Limited Mode............................................................................ 3

Fixed Channel Mode................................................................. 3

Setting (or Changing) Fixed Channel Mode for TV/VCR.......... 3

Removing Fixed Channel Mode for TV/VCR............................3

Programming Using Equipment Code Tables...........................4

Scanning for Equipment Codes................................................6

Switching Between TV and Amplifier Volume

Control................................................................................7

Programming the Remote to Control a Second Receiver

in AUX Mode......................................................................8

Reading Out the Remote Control Codes.................................. 9

Discrete Codes for Learning Remotes.....................................11

Avoiding Remote Conflicts...................................................... 12

Changing the Remote and Receiver Address ........................ 12

Changing the UHF Frequency Using the A/B Switch—

DISH Player-DVR 942, Duo ViP

222,

DuoDVR™ ViP

622 DVR, and

DuoDVR™ ViP

722 DVR Only ......................................13

Setting Up a TV1 UHF Pro Remote for the

DuoDVR™ 522 and DuoDVR™ 625 Only .......................14

Equipment Codes ................................................................... 16

Troubleshooting......................................................................24

Limited Warranty.....................................................................26

Your Remote Control Codes..........................Inside Back Cover

Use the key that

looks like this

Use the key that

looks like this

If your

receiver

looks like

one of

these...

If your

receiver looks

like one of

these...

If your

receiver looks

like one of

these...

If your

receiver looks

like one of

these...

If your

receiver looks

like this...

Use the key that

looks like this

DISH 501 & DISH 508

/ DISH Player-DVR 510

DISH 6000

DISH 721

DuoDVR™ 522

DuoDVR™ 625

Use the key that

looks like this

S-1

Solo ViP

211k

DISH 411 & Solo ViP

211

then

Select the Right Key

Remote keys are included in this replacement remote kit.

Quick Setup

Keys have two sides.

Look on both sides to find

the right key for your remote.

UHF

Pro

UHF

Pro

Solo DVR ViP

612

Use the key that

looks like this

Confirm Your Receiver Model

Duo ViP

222 & DuoDVR™ ViP

622

DuoDVR™ ViP

722

DISH JVC IRR

The remote functions as needed in regards to watching your

satellite television and VCR. It does not rewind or fast forward

while watching a recorded VCR tape.

S-2

Battery

Separate the key

from the remote

by inserting your

thumbnail or a coin

in the crease.

Remove the key by

grasping at the bottom.

Insert face up

the key you

selected on

the previous

page.

Pull the

remote

battery

cover off.

Note: If you are using the blue TV2 key that comes

already installed in your remote, skip this step and

proceed with the next step (Insert the Batteries).

Install Your Selected Key

Insert the Batteries

1 2

Replace

the

remote

battery

cover.

Insert 4 AAA

batteries,

making sure

to match the

plus (+) ends

with the plus

markings on

the battery

case.

Quick Setup

S-3

Quick Setup

RECORD

Turn your receiver and

TV on, and press

SYSTEM INFO on the

front of the receiver.

Confirm that you

see the System

Information screen.

Press RECORD on

your remote. The remote

address probably

changes on the screen.

Using your remote, select Done on the

System Info screen to confirm that

your remote operates your receiver.

If your remote has a blue number 2

key, you may need to go to your

remote TV2 location to confirm your

remote operates your receiver. If this

is not working, go back to step

Making the Remote Work

With Your Receiver

REMOTE

ANTENNA

If you installed a

UHF key, make sure

the UHF antenna is

installed on the back

of the receiver.

Green

(not black)

UHF Pro Symbol

If you installed one of these keys,

continue with step 2 on this page.

If you installed this

key, go to page 14

inside this guide.

S-4

Quick Setup

Turn your

TV on.

Press & hold the

TV Mode button

until all Mode

buttons light up.

Press

POWER.

Press the UP ARROW

on the remote repeatedly

(about 1 press per second)

until your TV turns off.

Press

POUND.

The TV Mode button

flashes three times.

Press the POWER

button to turn the TV on

and try other buttons

to make sure the code

works. If you want to try

another code, start over

from step 1.

Program the Remote to

Control Your TV

5 6

S-5

Quick Setup

Programming the

Recover Button for

TV2 Operation

For TV2 Remote Controls on

DuoDVR

™

522, DuoDVR

™

625,

Duo ViP

222, DuoDVR

™

ViP

622 DVR,

and DuoDVR

™

ViP

722 DVR Receivers

Press

STAR.

Press

POUND.

1 2

Press & hold the

TV Mode button

until all Mode

buttons light up.

Enter the channel

number you tune

your TV to when you

watch satellite

programming.

Use the RECOVER button as described in

If You Lose Your Picture on the next page (S-6).

Programming your RECOVER button allows you

to easily regain satellite programming if you

accidentally change TV channels or inputs.

Quick Setup/Operation

S-6

SELECT

Press and hold RECOVER until all

mode buttons light up.

If you see System Info, live

television, or the standby

screen, proceed to step 4.

Otherwise, continue to step 3.

Press RECOVER again & wait until

the mode lights stop flashing. If you

see System Info, live television, or

the standby screen, go to step 4. If

not, repeat this step until you do.

Press SELECT to resume watching TV.

Use the RECOVER button to get back to watching

satellite programming if you accidentally change

channels or inputs on your TV.

Placing Your Remote

in Limited Mode

If You Lose Your Picture

(How to Use the RECOVER Button)

Press

POUND.

Press & hold the

TV Mode button

until all Mode

buttons light up.

Press the

PAGE UP

button.

PAGE

To take the remote out of Limited Mode, use the PAGE DOWN

button instead of the PAGE UP button in step 2.

(Your screen may be different)

Limited Mode locks out all the TV mode operations except

for TV power, Mute, and Volume. This prevents you from

accidentally tuning away from satellite programming.

S-7

Operation

Remote Operation

SAT Mode

SAT

Remote key may

be different than

what is shown here

Receiver Power

& TV Power

Receiver Menu

Program Guide

Arrows/Select

Buttons

View Satellite

Programming

Digital Video

Recorder (DVR)

Buttons

Picture-In-Picture

(PIP) Buttons

Number Buttons

Top button turns the

receiver on and off

Bottom button turns

the TV on and off

Programming required

(see S-4)

Channel up/down,

navigate through

menus/guides and

select a desired

option

Exit out of any menu/

guide and go back to

viewing live TV

DISH

Explore interactive

TV features

Browse

See what is on other

channels while

watching TV

Enter a channel

number or select

menu items

Search for a program

Watch two separate

programs at once

(in Single Mode if available

on your receiver)

Recover

Recovers satellite

programming if your

TV input or channel

has changed

Format

Format the picture

to the desired width

to match the program

you are viewing

(this feature varies by receiver)

Display current and

future satellite

program listings

Page Buttons

Page up/down in

menus

Control TV volume

Programming required (see S-4)

Access receiver

features and settings

Themes

Search for programs

using Themes

Recall

Go back to last

channel viewed

Info

Display program info

Pause live TV and

play or record

programming

Volume & Mute Buttons

To use the features described in this section, make

sure you are in SAT mode by pressing the SAT Mode button.

Note: Some features may not be available depending on your receiver model.

Press this

button for

SAT Mode

S-8

Operation

Remote Operation

TV Mode

TV Power

TV Menu

Up/Down Arrow

Buttons

Picture-In-Picture

(PIP) Buttons

Number Buttons

Top & bottom

button

Turn TV on/off

Channel up/down

on TV

Enter a desired

channel number

on TV

Display PIP features

on some TVs with

PIP capabilities

Volume

Control TV

volume

Access menu

features available on

some TVs

TV/Video

Switch between

TV inputs

(not available

on all TVs)

Mute

Turn TV volume

on or off

Recall

Go back to last

TV channel viewed

To use the features described in this section, make

sure you are in TV mode by pressing the TV Mode button.

Remote programming is required. See S-4 for instructions.

TVTV

Note: Remote operation is different on DISH Network TVs.

See your DISH Network TV User's Guide for proper operation.

Press this

button for

TV Mode

Remote key may

be different than

what is shown here

Remote key may

be different than

what is shown here

S-9

Operation

Remote Operation

VCR Mode

VCR

VCR/DVD Power

& TV Power

TV/Video

Up/Down Arrow

Buttons

FWD

Number Buttons

Top button turns

the VCR/DVD

player on and off

Bottom button turns

the TV on and off

Channel up/down

on VCR

Forward a videotape

or DVD

Play

Play a videotape

or DVD

Pause

Pause a videotape

or DVD

Enter a desired

channel number

on VCR

Switch VCR between

its TV & VCR mode

Back

Rewind a videotape

or reverse a DVD

Stop

Stop playing

or recording a

videotape, or stop

playing a DVD

Record

Record on a

videotape

To use the features described in this section, make

sure you are in VCR mode by pressing the VCR Mode button.

You can use this mode to operate your DVD player instead of a VCR.

Remote programming is required. See page 2 for instructions.

Press this

button for

VCR Mode

REMOTE CONTROL OVERVIEW

Use this full-function remote to control a variety of DISH Network

receivers. Also, you can program the remote to control most of the

popular brands of audio/video equipment like a TV, VCR, DVD player,

or a second DISH Network satellite receiver. See Programming for

Other Equipment on page 2.

Note: This remote control may have features not used by your

receiver.

USING THE GUIDE

This guide makes it easy to set up and use your remote control. By now

you’ve noticed that the pages at the beginning of this User Guide

contain information on quick set up and remote control operation.

The rest of the guide contains in-depth information to help you get the

most from your remote control, including controlling other equipment

like TVs, VCRs, and DVD players.

REMOTE CONTROL MODES

Use the remote control’s mode buttons to set the remote to the correct

mode for the equipment. Be sure to program the remote to control other

equipment as described on page 2.

To change the mode, press the button for the equipment you want to

control. The mode button lights for two seconds to show you’ve set the

remote to that mode.

Great Idea: Whenever you finish using

other equipment (TV, VCR, DVD, etc.) be

sure to put the remote back in SAT mode.

If you program the remote to control other equipment, refer to the

following for remote control operation instructions:

• TVs, page S-8 (at the beginning of this guide).

• VCRs and DVD players, page S-9.

• DISH Network satellite receivers, page S-7.

• Stereo equipment uses only these buttons: SELECT (to change

inputs), MUTE, VOLUME, and POWER.

HOW THE REMOTE COMMUNICATES

Depending on how the remote is set up, the remote control may use

UHF radio signals, IR signals, or both to control the receiver. However,

only IR signals are used to control other equipment.

• IR signals travel short distances (up to 40 feet) and cannot go

through walls or other solid objects. Point the remote control

directly at the equipment you want to control, with no objects to

block the signal path.

• UHF signals travel longer distances than IR signals and can go

through walls and other solid objects. Because these signals

travel so far, the receiver may respond to signals from other

nearby remote controls. To handle this problem, you may want to

change the remote and receiver addresses (see page 12).

• If you’re set up to use UHF, make sure that the UHF remote

antenna is attached to the receiver’s back panel R

EMOTE

ANTENNA input so it can receive the UHF remote signals.

PROGRAMMING FOR OTHER EQUIPMENT

Page S-4 at the beginning of this guide shows you how to program the

remote to control a TV. The following section uses a different method

to program the remote to control a TV or other equipment (such as a

VCR, DVD player, tuner, amplifier, or a second TV). You can program

the remote by either following the instructions in Programming Using

Equipment Code Tables on page 4, or the Scanning for Equipment

Codes procedure described on page 6.

COMBINATION EQUIPMENT (FOR EXAMPLE, TV/VCR)

When programming the remote to control combination equipment,

such as a TV/VCR or a TV/DVD, program the remote control in one

mode, and then repeat the procedure in the other mode. For example, to

program the remote to control a Magnavox TV/VCR using code 887,

follow the instructions to program the remote to control the TV using

code 887, and then repeat the instructions for the VCR using code 797.

Put the remote in TV mode to use the TV or VCR mode to use the

VCR.

LIMITED MODE

You can program your remote control in Limited Mode to keep from

accidentally changing the channel on your TV or VCR. When Limited

Mode is enabled, you cannot select TV mode. If you press the TV

button while TV mode is programmed in Limited Mode, the TV button

flashes and the SAT button lights, telling you cannot switch to TV

mode. The remote then moves back to SAT mode.

When you use the remote to control your TV in Limited Mode, you are

only able to use the POWER, MUTE, and VOLUME buttons to

control your TV. Also, when you use the remote to control your VCR

in Limited Mode, you are only able to use the POWER and VCR

function buttons. The section Programming Using the Equipment Code

Tables has a step that tells the remote control to go into Limited Mode.

Also, a quick way to put the remote in Limited Mode is on page S-6.

Note: Limited Mode cannot be used with audio amplifiers.

FIXED CHANNEL MODE

You can program your remote control in Fixed Channel Mode to

automatically set the TV and/or VCR to a given channel when you

press either RECOVER or the SAT button.

SETTING (OR CHANGING) FIXED CHANNEL MODE FOR TV

AND/OR VCR

1 Press and hold the TV or VCR mode button until all four mode

lights illuminate.

2 Press the STAR key (*). Enter a channel, using two or three digits

between 02 and 125. For example, to set channel 25, enter *25.

3 Press the POUND (#) key. The TV or VCR mode button flashes

three times.

EMOVING FIXED CHANNEL MODE FOR TV AND/OR VCR

1 Press and hold the TV or VCR mode button until all four mode

lights illuminate.

2 Press the STAR (*) key followed by two zeros (*00).

3 Press the POUND (#) key. The TV or VCR mode button flashes

three times.

PROGRAMMING USING EQUIPMENT CODE TABLES

You can set up the remote to control other equipment using the

equipment code tables listed on page 16 and the modes as shown on

page 1. To control a receiver in AUX mode, see page 8.

Instructions Additional Information

1 Turn the equipment on. Use the equipment’s front panel

buttons or its remote control.

2 Find the brand name of the

equipment in the tables

starting on page 16.

If the brand isn’t listed, see

Scanning for Equipment Codes

on page 6.

3 Press and hold the mode

button until all the other

mode buttons light up, and

then let go of the button.

The mode button flashes.

For example, hold the TV mode

button for a TV until all of the

other mode buttons light. When

you let go, TV mode button

flashes.

4 For AUX mode only. Press

0 for a second TV, or 1 for a

second VCR, or 2 for a

tuner, or amplifier.

This step is for programming

the kind of equipment that

should be programmed in AUX

mode. If you’re not

programming in AUX mode,

skip to step 5.

5 Enter one of the three-digit

equipment codes from the

table using the number

buttons.

The three-digit equipment code

should be for the brand name of

your equipment that you found

in step 2.

6 If you want to program

Limited Mode, press 1.

If not, skip to step 7.

See Limited Mode on page 3 for

more information.

7 Press POUND (#). If you entered the code

correctly, the mode button

flashes three times.

8 Press POWER to turn off

the equipment. If the

equipment does not turn

off, go to step 10.

If the code works, the

equipment should turn off.

9 Turn the equipment back

on and try some other

buttons to make sure they

work. If the code works for

other buttons, stop here.

Note: If you have

programmed your remote in

Limited Mode, only the

MUTE and VOLUME

buttons work.

For example, sometimes

POWER works when other

buttons don’t.

10 If the code doesn’t work,

repeat steps 3 through 9

with another equipment

code from the tables.

Try every code listed for your

brand until one works for your

equipment.

11 If you can’t find a code that

works, try Scanning for

Equipment Codes that

follows.

Instructions Additional Information

SCANNING FOR EQUIPMENT CODES

Instructions Additional Information

1 Turn the equipment on. Use the equipment’s front panel

buttons or its remote control.

2 Press and hold the mode

button until all the other

mode buttons light up, and

then let go of the button.

The mode button flashes.

For example, hold the TV mode

button for a TV until all of the

other mode buttons light. When

you let go, TV mode button

flashes.

3 For AUX mode only. Press

0 for a second TV, 1 for a

second VCR, or 2 for a

tuner, or amplifier. Then

press the STAR (*) button.

This step is for programming

the kind of equipment that

should be programmed in AUX

mode. If you’re not

programming in AUX mode,

skip to step 4.

4 Press POWER. This step puts your remote in

the scan mode.

5 Press either the UP or

DOWN ARROW

repeatedly until the

equipment turns off.

As you press the UP or DOWN

ARROW, the remote tries each

code in the memory to see if it

can turn off your equipment.

When the equipment turns off,

you have found a code that

might work.

Note: The mode button for the

equipment flashes rapidly eight

times when you’ve scanned all

the codes for that equipment.

6 Press POUND (#). The mode button flashes three

times if you have entered the

code correctly. This step stores

the code you found.

SWITCHING BETWEEN TV AND AMPLIFIER VOLUME

ONTROL

When you set up the remote to control a TV, the MUTE and VOLUME

buttons control the TV volume, even if your remote control is in SAT

mode. However, if you want to use the AUX mode to control a tuner or

amplifier that has a volume setting, you can set up the remote to control

the tuner or amplifier’s volume instead of the TV volume while your

remote control is in SAT mode. Follow the instructions in the left

column to switch controlling volume in AUX mode. To change back to

controlling the TV volume in SAT mode, follow the instructions in the

right column.

7 Turn the equipment back

on and try some other

buttons to make sure they

work.

Press POWER to turn the

equipment back on. Try some

other buttons to make sure they

work. Sometimes POWER

works when other buttons

don’t.

8 If necessary, repeat this

procedure until you’ve tried

all the codes.

You may need to repeat the scan

to find the best code for your

equipment.

9 Once you find a code that

works, consider using

Limited Mode.

See page S-6, Placing Your

Remote in Limited Mode for

putting your remote in Limited

Mode.

Control Amplifier Volume Control TV Volume

1 Press and hold the AUX

mode button for three

seconds, and then let go of

it. The AUX mode button

blinks.

1 Press and hold the TV

mode button for three

seconds, and then let go of

it. The TV mode button

blinks.

2 Press the POUND (#)

button.

2 Press the POUND (#)

button.

Instructions Additional Information

PROGRAMMING THE REMOTE TO CONTROL A SECOND

ECEIVER IN AUX MODE

If you have another DISH Network satellite receiver installed, you can

use this remote in AUX mode to control it along with your new

receiver. When you program the remote to control the other receiver,

the remote sends out IR and UHF (not UHF Pro) signals to the receiver.

You can program the remote to control any other DISH Network

satellite receiver, except for following:

• TV2 on Duo 322, DuoDVR 522 (also known as DISH Player-

DVR 522), DuoDVR 625 (also known as DISH Player-DVR

625), DISH Player-DVR 942, Duo ViP 222 (also known as ViP

222), DuoDVR ViP 622 DVR (also known as ViP 622 DVR) ,

and DuoDVR ViP 722 DVR (also known as ViP 722 DVR)

• DishPlayer 7100/7200

1 Turn on the other receiver. Use the SYSTEM INFO button on the

front panel to open the System Info screen.

3 Press the plus (+) side of

the VOLUME button.

3 Press the plus (+) side of

the VOLUME button.

4 Press the 0 number button. 4 Press the 0 number button.

5 Press the POUND (#)

button.

5 Press the POUND (#)

button.

The AUX mode button

flashes three times.

The TV mode button

flashes three times.

AKE SURE THE REMOTE

CONTROLS THE AMPLIFIER’S

VOLUME:

AKE SURE THE REMOTE

CONTROLS THE TV’S VOLUME:

6 Press the SAT mode

button.

6 Press the SAT mode

button.

7 Press the plus (+) and

minus (-) sides of the

VOLUME button.

7 Press the plus (+) and

minus (-) sides of the

VOLUME button.

8 The equipment’s volume

changes and the AUX mode

button lights instead of the

TV mode button.

8 The TV’s volume changes

and the TV mode button

lights instead of the AUX

mode button.

Control Amplifier Volume Control TV Volume

Page is loading ...

Magnasonic 167820 User manual

Brand: Magnasonic

Model: 167820

Category: Remote controls

Type: User manual

This manual is also suitable for

Download PDF

report

Magnasonic 167820 User manual

This manual is also suitable for

Magnasonic 167820 User manual

Related papers

Other documents