© 2018 American Honda Motor Co., Inc. – All Rights Reserved. BII09104-18 (1805) 1 of 4
VERSION 1
Publications No.
Issue Date
INSTALLATION
INSTRUCTIONS
Accessory Application
SPARE TIRE KIT
P/N: 06421-TY2-A14ZA (19
")
2019 RLX
MAY 2018
PARTS LIST
Spare tire rim
Valve stem
Spare tire caution label
Hold down bolt
Tool case
Jack
Wheel nut wrench/Jack handle
Extension bar
Tire and load information label
Spare tire (T165/80D17)
(sold separately)
Carpet
2 Clips
TOOLS AND SUPPLIES REQUIRED
Isopropyl alcohol
Shop towel
Trim clip remover
INSTALLATION
NOTE:
• Be careful not to scratch the interior trim when installing
the spare tire kit.
• Install the correct size tire.
• Use a tire changer, and the Operation Manual
furnished with the tire changer to install the spare tire to
the spare tire rim.
• Give all the removed parts to your client.
Client Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
2 of 4 BII09104-18 (1805) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
1. Using isopropyl alcohol on a shop towel, clean the
spare tire rim in the area shown.
2. Remove the adhesive backing from the caution
label, and attach the caution label to the spare tire
rim in the area shown.
3. Use a tire changer to install the spare tire (sold
separately) onto the spare tire rim. Inflate the spare
tire to 60 psi (420 kPa).
Installing the Spare Tire Kit
4. With the trunk open, lift the trunk floor cover up and
remove it.
CAUTION
LABEL
SPARE TIRE RIM
(Clean this area
with isopropyl
alcohol.)
VALVE
STEM
HOLE
5. Remove the tool box.
6. Transfer the tools from the existing tool box to the
new tool box supplied. Set the old tool box aside, it
will not be reused.
TOOL BOX
Set aside.
TOOL BOX
Set aside.
NEW TOOL
BOX
© 2018 American Honda Motor Co., Inc. – All Rights Reserved. BII09104-18 (1805) 3 of 4
7. Install the jack, the wheel nut wrench/jack handle,
and the extension bar into the new tool case.
8. Remove the center clip from the trunk lining. Then
slide the carpet in-place.
NOTE: Make sure the mark is facing up as shown.
NEW TOOL
CASE
JACK
WHEEL NUT
WRENCH/JACK
HANDLE
EXTENSION
BAR
CENTER CLIP
Do not reuse.
CARPET
MARK
9. Using a marker, mark the carpet through the clip
hole.
10. Remove the carpet, and make a 7 mm hole in the
marked position.
11. Secure the carpet using the two clips as shown.
4 of 4 BII09104-18 (1805) © 2018 American Honda Motor Co., Inc. – All Rights Reserved.
12. Install the spare tire assembly into the spare tire area
(label side down), and secure it to the vehicle using
the spare tire bolt provided. Tighten the bolt
securely.
13. Install the new tool box into the trunk area over the
spare tire in the direction shown.
SPARE TIRE
ASSEMBLY
HOLD-DOWN
BOLT
SPARE TIRE
AREA
SPARE TIRE
NEW TOOL
BOX
14. Open the driver’s door and locate the “TIRE AND
LOADING INFORMATION” label on the doorjamb.
Using isopropyl alcohol on a shop towel, clean the
doorjamb over the existing label.
15. Remove the adhesive backing from the new “TIRE
AND LOADING INFORMATION” label, and attach it
over the existing label.
DRIVER’S
DOORJAMB
EXISTING TIRE AND
LOADING INFORMATION
LABEL
(Clean with
isopropyl alcohol.)
NEW TIRE AND LOADING
INFORMATION LABEL
/