Allen home ASMM-017-2866 Assembly Instructions

Brand
Allen home
Model
ASMM-017-2866
Type
Assembly Instructions
Mantel Assembly Instructions – ASMM-017-2866
WARNING
Read and understand this assembly instructions manual and the electric fire
instructions manual prior to installing the electric fire in the mantel and operating the
electric fire. Failure to do so could result in a fire, electric shock, or a personal
serious injury.
Mantel Assembly Hardware
Long Allen Head
Screw (6*25) -
20 pcs
#6 washer –
20 pcs
Short Allen
Head Screw
(6*15) - 18 pcs
Shelf
Support - 8
pcs
Hinge – 4 pcs
Hinge Screw
– 16 pcs
Door knob – 2
pcs
Door knob
screw – 2 pcs
"L" bra c ke t – 9
pcs
MDF block -
2 pcs
Back panel
screw – 24 pcs
Allen wrench
– 1 pc
Media Mantel Hardware
Mantel Assembly Instructions – ASMM-017-2866
Mantel Components
Item
Description
Description
A
Base
Left back panel
B
Left outside panel
Right back panel
C
Left inside panel
Left door
D
Right inside panel
Right door
E
Right outside panel
Left Shelf
F
Left surround panel
Right Shelf
G
Right surround panel
Top assembly
H
Top surround panel
DO NOT FULLY TIGHTEN FASTENERS UNTIL ALL PIECES ARE IN PLACE.
The Bennett 66 is designed and engineered to have extremely tight fit between
panels once assembled. For overall ease of assembly, it is generally best to
tighten the fasteners of the individual panels just enough to still allow some
movement as needed to assemble the next panel.
When all pieces are in place and proper alignment is achieved, finish tightening all
fasteners
IMPORTANT!
Mantel Assembly Instructions – ASMM-017-2866
STEP 1
STEP 2
STEP 3
STEP 4
4 plcs >
B
E
A
4 plcs >
A
H
G
F
a) Unpack the carton and place all parts
separately on the floor.
b) Place the base (A) flat on the floor as shown
in Fig 1.
a) Attach the Left outside panel (B) in position
using (2) M6 x 25 screws & washers as
shown in Fig 2.
b) Attach the Right outside panel (E) in position
with (2) M6 x 25 screws & washers as shown
in Fig 2.
Fig 1.
A
Fig 2.
C
D
a) Attach the Left inside panel (C) in position
using (2) M6 x 25 screws & washers as
shown in Fig 3.
b) Attach the Right inside panel (D) in position
with (2) M6 x 25 screws & washers as shown
in Fig 3.
Fig 3.
a) From the front side, carefully place the Left &
Right surround panels (F) & (G) in position
ensuring there are no gaps.
b) From the back side, attach the Left surround
panel (F) & the Right surround panel (G)
using (12) M6 x 15 screws & (6) “L” brackets
in the positions shown in Fig 4.
c) Carefully place the Top surround panel (H) in
position & attach it using (2) MDF boards &
(4) M6 x 25 screws & washers in the
positions shown in Fig 4.
Fig 4.
2 plcs
6 plcs
Important: Do not fully tighten screws until all parts are assembled
Text
Mantel Assembly Instructions – ASMM-017-2866
STEP 5
STEP 6
STEP 7
O
8 plcs
a) Carefully align the top assembly (O) in
position on top of the (4) vertical panels.
b) From the back side, attach the top assembly
(O) to the (4) vertical panels (B), (C), (D), &
(E) using (8) M6 x 25 screws & washers as
shown in Fig 5.
c) Attach the top surround panel (H) using (3)
“L” brackets & (6) M6 x 15 screws
Fig 5.
a) From the back side, attach the Left back
panel (I) & the Right back panel (J) using (12)
wood screws each as shown in Fig 6.
J
I
(24) screws >
Fig 6.
a) Return to the front side of the unit & insert the
(8) shelf supports in the desired pre-
drilled shelf height positions in the vertical
panels.
b) Place the (2) shelves (M) & (N) in the desired
positions as shown in Fig 7.
M
N
(8) shelf supports >
Fig 7.
3 plcs
H
It is strongly recommended for (2) adults to perform this step.
Mantel Assembly Instructions – ASMM-017-2866
STEP 8
STEP 9
a) Place the (2) doors (K) & (L) flat face down
on the floor on a cardboard surface.
b) Install the (2) hinge assemblies in the pre-
drilled positions on each door using (2) wood
screws each as shown in Fig 8.
c) Turn the door over & assemble the knob in
the pre-drilled position.
Fig 8.
a) Place the Right door (L) in the position shown
in Fig 9 & attach it to the Right outside panel
(E) in the pre-drilled hinge holes using (4)
wood screws.
b) Repeat step 9a) for the Left door (K)
c) Open & close the doors to ensure they are
easy to operate with minimal rubbing or gaps.
Fig 9.
(2) hinges each door
(4) screws each door
The mantel is now fully assembled and ready for installation of the electric. Please
follow the electric fire instruction manual for secure installation of it in this mantel.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Allen home ASMM-017-2866 Assembly Instructions

Brand
Allen home
Model
ASMM-017-2866
Type
Assembly Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents