User Guide
Product Overview
Thank you for your purchase of the
ProVisio S rangender, please read the
instructions carefully before using it for
the rst time.
The ProVisio S laser rangefinder is
designed for outdoor activities such as
golf, hunting, sightseeing and more. It
offers many different features such as a
compact design with a light carry case. It
is the perfect device for any golfer look-
ing for accurate measurements.
Safety Instructions
(1) Warning
• Do not stare into the laser beam.
• Do not aim the rangender directly
at the sun, it can permanently affect
your vision and damage the device.
• The rangender is made for uses in
temperatures between 0°C (32°F)
and 40°C (104°F).
• Keep the eyepiece away from direct
sunlight.
(2) Disposal
• It is prohibited to dispose used bat-
teries with household waste. Please
collect used batteries and contact
your local authorities to dispose them
appropriately, in accordance with
regulations.
Rangender Parts & Pieces
1. Power/Measure button
2. Mode change/Unit button
3. Laser emitter/Objective Lens
4. Laser receiving Lens
5. Battery knob
6. Eyepiece
7. Slope mode on & off
8. Battery compartment
9. Tripod screw hole
Icons on LCD Display
1. Low battery indicator
2. Golf ag scan icon
3. Point to point measurement
4. From left to right : distance,
measuring unit
5. Vertical height
6. Bull’s eye
7. From left to right : slope, distance,
measure unit
8. From left to right : angle icon, angle
readings, angle unit
Initial Operations and Settings
Eyepiece
Adjust the eyepiece knob to focus
the target
Switch ON or OFF
Press the to switch ON.
The device automatically turns off after
8s of inactivity.
Calibration
This device is already calibrated. If it
gives a wrong measurement, the device
should be re-calibrated manually. Turn
off the device, press and hold the power
button for two seconds to enter the cali-
bration interface. The letters “Angle Cal”
will show up on the screen. Hold still for
several seconds to complete the calibra-
tion. If the calibration cannot be com-
pleted in time, the device will turn off
automatically indicating the calibration
has failed.
Unit Change
Hold for 2s the button to change the
unit (yd or m).
Measuring Mode Change
Please adjust the eyepiece to focus the
target before measuring.
While measuring, if the target reection
is weak or out of the measuring range, it
will display “---”.
The measurement range will be affected
by materials of the target, inclined angled
of the target surface, visibility, weather…
Continuous measurement: hold the mea-
sure button for 2s to activate the con-
tinuous measurement option, loosen to
deactivate the feature.
Short press to switch to either one
of the different modes as shown below :
Battery Installation and In-
structions
Please use 1x CR2 battery.
When (low battery) is displayed,
replace the battery, otherwise the
chances of error in the measuring will
increase. Remove the battery from the
rangender if the device is not used for
a long time.
Use coin or any other tool to turn the
battery cover anti-clockwise until the
battery cover is opened.
Install 1x CR2 battery and respect the
correct polarity.
When the battery is properly installed,
turn and tighten the cover clockwise.
Vertical Height Measuring
Mode
Short press to vertical height measur-
ing mode. Aim at the rst target, press
to get the distance and angle (angle
between the measured distance and hor-
izontal surfaces). Move to the second tar-
get, press to get the second distance
and angle (angle between the measured
distance and horizontal surfaces), the
vertical height between these two points
will be displayed on the top, the absolute
value of the difference between the two
angles will be displayed at the bottom.
Remarks : the distance refers to the verti-
cal height between these two points.
Point-to-Point Measuring
Mode
Press to activate point-to-point mea-
suring mode. Aim at the target and
press . The first distance will be
displayed. Target the second point and
press . The second distance will
be displayed. The distance and angle
between the two points will be calculated
automatically.
Note : stand still while measuring
the target.
Golf Ballistic Mode
Distance + Ballistic distance + Angle
Short press to activate single dis-
tance measures.
Long press (2s) to activate continu-
ous measures.
Golf Ballistic (Scanning) Mode
Distance + Ballistic distance + Angle
(scanning mode)
Aiming at the target, short press (Flag
icon is flashing). Scan slowly back and
forth on both sides of the measured
target, after 1.5s, the agpole will stop
ashing, the data will show the distance
of the measured target, the ballistic dis-
tance and angle.
Distance, Height and Angle
Measurement
Distance + Height + Angle
Short press to activate single dis-
tance measurement.
Long press to activate continuous
measurement.
Notice
1. In order to protect the coating of
the lens, do not touch lens with your
ngers.
2. This laser rangender has been
precisely calibrated by instruments,
please send back to dealer for repair-
ing instead of doing it yourself.
3. If the lens is contaminated, please
wipe gently with a clean cloth.
4. Keep the product away from mois-
ture during storage. Keep in a dry,
cool and well-ventilated place to
avoid direct sunlight and dust.
5. Water may affect the precision of the
distances and may cause errors in
very bad weather conditions.
Contact us
ProVision Golf
Website : www.provisiogolf.com
Technical Data
Model ProVisio S
Measuring range 650yds (594m)
Battery CR2
Measuring unit Yards/Meters
Measuring accuracy +/- 0.5yds
Measuring angle 90°
Ballistic compensation angle range 20°
Angle accuracy +/- 1°
Wavelength 905nm
Vision safety FDA (CFR21)
Field of view 7°
Scope magnication 6x
Objective lens diameter 22mm
Eyepieces lens diameter 16mm
Exit pupil diameter 3.7mm
Diopter +/- 5D
Diopter
adjustment Eyepiece Adjustment
Operating temperature
0°C (32°F) and 40°C (104°F)
Display LCD
Auto power switch-off
8s after inactivity
Dimension 121*79*45mm
Weight (without battery) 213g
/
