BALANCED EQUALIZER
IN NORSE MYTHOLOGY, LOKI IS THE TRICKSTER GOD.
LOKIUS IS FROM A ROMAN CONFLATION—LOKIUS MAXIMUS.
HEY, NOBODY SAID WE HAD TO MAKE SENSE ALL THE TIME.
IN ANY CASE, THIS IS A BIGGER, BETTER LOKI MINI+—
SIMPLE AS THAT!
LOKIUS
OWNER’S MANUAL
What is bigger than Loki Mini+? Lokius. Short
for Lokius Maximus (yeah, we know, that’s a
Roman thing, got it, we’re mixing cultures, boo,
bad Americans). In any case, Lokius gives you
two more bands, balanced input and output,
and our super-buffer and current-feedback
discrete gain stage. So, yeah. Even trickier.
Yeah, and we’re back to Norse. Relax and
don’t be so pedantic.
INTRODUCTION
WHAT’S IN THE BOX
(1) Lokius
(1) Wall-Wart
The following is required by the roughly 9,542
government agencies and regulations we have to
comply with. If you have some common sense, they
should seem pretty straightforward. In any case, read these
instructions before proceeding farther, follow all instructions,
and heed all warnings. Or else!
1. If you don’t know how to install audio devices, get a
qualied professional to help.
2. Never use this device near water, and clean only with a
dry cloth.
3. Assure adequate ventilation, do not block any ventilation
openings, or place near heat sources.
4. Use only the supplied power cord or suitable replacement.
Route cords away from trac areas and protect them from
being pinched. Unplug the cord from the outlet if the apparatus
is unused for a long period of time.
5. To prevent electric shock, do not use the plug with an
extension cord, receptacle, or outlet unless blades can be
fully inserted.
6. Refer all servicing to qualied service personnel. Service is
required when the device has been damaged, including cord or
plug damage, liquid has been spilled or objects have fallen into
the device, the device has been exposed to rain or moisture,
does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO
RAIN OR MOISTURE.
GETTING STARTED
1. Locate Lokius away from other
components that have transformers in them.
As in, Lokius is an LC (inductor-capacitor) equal-
izer. The inductors may pick up hum from other
components. Stacking Lokius on top of a Vidar
(for example) may cause audible hum through
your speakers or headphones. If you hear hum,
move Lokius away from other components.
That’s why they make these things called
“shelves” and “racks.”
2. Connect Lokius to your system,
either before or after your preamp.
If you have multiple sources, you can connect
Lokius after your preamp, so you can control the
frequency response of all sources. This is our
recommended connection for most systems;
Lokius has a very low noise oor that should be
below the level of most preamps.
If you have a single source, you can connect
Lokius before your preamp—Lokius has the
headroom for standard 2V/4V RMS single-
ended/balanced line outputs.
Connect Lokius via balanced or single-ended
using high quality XLR or RCA cables.
Finally, connect the supplied wall-wart to
Lokius and turn it on.
Note: Both balanced and single-ended outputs are on all
the time and are completely independent—you can connect
balanced to one amp and single-ended to another (or a
subwoofer).
3. Adjust Lokius to your preference.
That’s really it! Adjust Lokius to compensate
for imperfect systems or recordings. You can’t
really hurt anything, so go wild!
Note: If you are using sources with more than 2V or 4V
RMS output direct into Lokius before your preamp, you
may experience distortion with Lokius controls turned up
to maximum. Lokius is designed for standard 2V/4V RMS
single-ended/balanced line levels (or lower).
ABC12300000 XXVAC/XA
AC
IN
1 Balanced Input. Connect your preamp out (or
single source) with high-quality XLR cables. Or
you can use crappy cables (but why)?
2 Single-Ended Input. Connect your preamp
out (or single source) with high-quality RCA
cables. Again, you could use crappy cables, but
why? You don’t have to spend a ton to get good
cables.
3 Balanced Output. Connect to your amp (or
headphone amp) with high-quality XLR cables.
Or, you can connect to your preamp or passive
volume control in a simple system.
GETTING CONNECTED
1
2
3
4
4 Single-Ended Output. Connect to your amp (or
headphone amp) with high-quality RCA cables.
Or, you can connect to your preamp or passive
volume control in a simple system.
5 Power Switch. Turn on the switch. The
protection relay keeps the EQ disengaged for
10-20 seconds, then it will engage with a click.
6 Power Input. Connect the supplied wall-wart
cable to the jack labeled “AC IN.” Do not use any
other wall-wart, or bad things might happen.
(Well, technically, any 14-16VAC, 1-2A adapter is ne, but
note the “VAC,” not “VDC.”)
56
ABC12300000 XXVAC/XA
AC
IN
1 Input Select. Up for balanced input (XLR),
down for single-ended (RCA). Simple as that.
2 Process/Bypass. Up = equalization active,
down = completely bypassed (only a relay and
resistor in the signal path).
3 20Hz Knob. AKA very low frequencies. Turning
the knob clockwise increases output, counter-
clockwise decreases. Simple as that.
4 120Hz Knob. Similar to a standard “bass
control.” Works just like the above. Clockwise
for moar bass, counterclockwise for less.
OPERATION
5 400Hz Knob. AKA lower mids. You have
the directions good on this now, right?
6 2kHz Knob. AKA presence. Clockwise for
more, counterclockwise for less.
7 6kHz Knob. Similar to a standard “treble
control.” You know the drill.
8 16kHz Knob. AKA air or extremely high
frequencies. Works like all the other knobs.
9 Power LED. When this lights up, Lokius is on.
1
2
3 4 5 6 7 8
9
I hear hum through the speakers or
headphones, what do I do to x it?
As noted in the Getting Started section, Lokius is
an inductor-capacitor equalizer, and may pick up
hum from other components that have trans-
formers in them. “Stacking” is ne for wall-wart
powered devices, but components that plug into
the wall may have transformers, and may cause
hum. Move the Lokius away from those compo-
nents to eliminate the hum.
Lokius doesn’t equalize anything for a while
after I turn it on.
That’s perfectly normal. Lokius delays the output
for 10-20 seconds after you turn it on so the
output stages can stabilize.
The sound is distorted.
If you have a “hot” source, with over 2V RMS
single-ended or 4V RMS balanced running
directly into Lokius (not after your preamp) you
may have distortion with Lokius’ knobs turned all
the way up. All Schiit devices output 2V/4V RMS
or less and are compatible with Lokius.
FAQ
No, I mean I have Lokius off and it’s still dis-
torted—shouldn’t this be a bypass mode?
Please turn Lokius on and switch it to Bypass
mode in order to have a straight-through con-
nection. When Lokius is off, the input stage is
unpowered and may load some sources.
Can I use both balanced and single-ended
outputs at the same time?
Yes. They are completely independent.
Connecting to one does not inuence the other.
Can I use both balanced and single-ended
inputs at the same time?
Yes, there is a front panel switch to select
between them.
Lokius doesn’t turn on, what do I do?
Plug it in to a different AC socket. Ensure you
are not currently in a blackout. Then email us if it
still doesn’t work.
Schiit Audio warrants to the original purchaser that this product shall be free from defects in material and workmanship
for two (2) years from the date of purchase. If a defect covered by this warranty occurs during this period, Schiit Audio
will repair the defective product, free of charge. Date of purchase will be based on customer receipts, otherwise date of
manufacturing will be used.
If you believe you need warranty service, contact us rst. Schiit Audio products sent back to us without a Return Authoriza-
tion (RA) will be returned to the sender without repair. To contact us and obtain an RA, email [email protected].
Warranty Limitations. This warranty shall not apply if a product: (a) is modied or tampered with; (b) is damaged by
negligence, accident, unreasonable use, or other causes unrelated to defective materials or workmanship, or (c) has had the
serial number altered or removed.
Any implied warranties, including warranties of merchantability and tness for a particular purpose, are hereby limited in
duration to the warranty period of 2 years. In no event shall Schiit Audio be liable for consequential or incidental damages
resulting from the breach of any implied or expressed warranties. Some states do not allow these limitations, so they may
not apply to you. You may also have other rights which vary from state to state or province to province.
2-YEAR LIMITED WARRANTY
This product is in compliance with standards
and regulations of the European Community.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
SCHONSTEDT Loki Pipe & Cable User manual
-
Mackie BIGK NOB User manual
-
Manley TNT 2-Channel Mic Preamp Owner's manual
-
Mackie 1202 User manual
-
-
Audio Technologies Incorporated ML200 Operating And Maintenance Manual
-
-
-
-
ATI Technologies DA103 Operating And Maintenance Manual
