Astria Fireplaces Brentwood LV Instruction Sheet

Brand: Astria Fireplaces

Model: Brentwood LV

Category: Fireplaces

Type: Instruction Sheet

This manual is also suitable for

Astria Fireplaces Brentwood LV offers a unique heating solution for your home. With its powerful blower, this fireplace insert evenly distributes heat throughout your living space, ensuring a warm and cozy ambiance. Installation is made easy with the pre-installed junction box and 3-prong receptacle, allowing you to simply plug in the blower and enjoy instant warmth. Remember to always follow the provided instructions for a safe and optimal heating experience.

UZY-6-B BLOWER KIT

P/N 900597-00

Rev. NC, 10/2015

HEARTH PRODUCTS

KITS AND ACCESSORIES

KIT CONTENTS

1 ea. UZY-6-B Blower Assembly

1 ea. Mill-Pack

1 ea. Instruction Sheet

TOOLS NEEDED

Robertson (square) or Phillips (star) screwdriver

INSTALLATION INSTRUCTIONS FOR INSTALLING UZY-6-B REPLACEMENT BLOWER KIT

FOR USE WITH WOOD-BURNING FIREPLACES LISTED IN TABLE 1

Blower Kit

Cat. No. Model Where Used

J8003 UZY-6-B Ladera™, Brentwood™ LV, WRT3820WS, WRT4820WS,

BIS® Nova and BIS Ultima

Table 1

INSTALLATION INSTRUCTIONS

Step 1. Open door, and remove the andirons, using a square or phillips

screwdriver. Then remove front and bottom refractories.

Step 2. Unscrew the access plate located in the ﬁrebox ﬂoor (12 screws).

Remove the access plate and the high heat cement used to seal it.

Step 3. Unplug the blower from the electric receptacle located on the

right side of the ﬁreplace.

Step 4. Unscrew the blower using a Robertson (square) or Phillips

(star) screwdriver. The location of the (2) screws depends on

the version of the blower installed (see Figure 1). They can be

at each end of the support bracket close to the ﬂoor (Version B)

or on top of the support bracket near the left side (Version A).

See Figure 1.

Step 5. Take the blower out of the ﬁreplace through the access opening.

Figure 1

WARNING

The blower must be plugged directly into a properly grounded

three-prong receptacle, 120 VAC, 60 Hz, single phase. Do not

cut or remove the grounding prong from this plug.

Installation must be in accordance with National Electrical

Code, ANSI/NFPA 70 - latest edition. In Canada, the current

CSA C22.1 Canadian Electrical Code - latest edition.

GENERAL INFORMATION

This blower kit can easily be installed when the ﬁreplace has a pre- installed

junction box with 3 prong receptacle. You just have to plug it in.

If you encounter any problems, need clariﬁcation of these instructions or

are not qualiﬁed to properly install this kit, contact your local distributor

or dealer.

Read this instruction sheet in its entirety before beginning the installation.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND

OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO

THESE INSTRUCTIONS.

SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL

BEFORE PROCEEDING.

Version A Unscrew these

two screws

Version B

Or these screws

to remove the blower

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 2

Figure 3

Installing the new Blower

Step 6. Insert the new blower in the ﬁreplace. Since the new support

bracket is bigger, insert the blower into the access opening with

the back side down, sliding it backward in the ﬁreplace and

rotating it up counterclockwise into position (see Figure 2).

Finishing the installation

Step 10. Plug the blower back in the electrical receptacle.

Step 11. Apply new high temperature sealant (Mill-Pack, included) to seal

the access plate, making a 1/4” bead covering all (12) screw

holes of the access opening.

Step 12. Reinstall the access plate and secure to the back of the ﬁrebox ﬂoor

using the (7) 10-32x1/2” screws supplied.

Step 13. Reinstall the front and bottom refractories and the andirons.

3 - Rotate counterclock-

wise into position

Step 9. Screw in through these holes to the ﬁreplace back.

By offsetting the blower 4” to the right, this spacer

will be centered in the ﬁreplace.

2 - Slide the blower to the

back of the ﬁreplace

1 - Insert the blower

backside down

Steps 7 and 8 apply if the blower you removed is an older version.

Otherwise goto step 9.

Step 7. There are two 1” spacers left after removing the old blower.

Leave them there because they are riveted, although they won’t

be used anymore.

Step 8. Position the blower so that the new 1” spacer is touching the

back of the ﬁreplace and the blower is offset about (4) inches to

the right (so the motor of the blower is not under the ﬁrebox).

Step 9. Screw the blower in place using the supplied (4) black self-tapping

screws through the holes of the 1” spacer and securing through

the ﬁreplace back (see Figure 3, step 9).

Reinstall these (2) screws

into the 1” spacer.

Innovative Hearth Products reserves the right to make changes at any time,

without notice, in design, materials, speciﬁcations, prices and also to discon-

tinue colors, styles and products. Consult your local distributor for ﬁreplace

code information.

P/N 900597-00 Rev. NC 10/2015 1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Page is loading ...

Astria Fireplaces Brentwood LV Instruction Sheet

Brand: Astria Fireplaces

Model: Brentwood LV

Category: Fireplaces

Type: Instruction Sheet

This manual is also suitable for

Download PDF

report

in other languages

français: Astria Fireplaces Brentwood LV

Astria Fireplaces Brentwood LV Instruction Sheet

This manual is also suitable for

Astria Fireplaces Brentwood LV Instruction Sheet

in other languages

Related papers

Other documents