Astria Fireplaces WRT3820 Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
WRT3820
Category
Fireplaces
Type
Instruction Sheet

This manual is also suitable for

1
UZY-6-B BLOWER KIT
P/N 900597-00
Rev. NC, 10/2015
HEARTH PRODUCTS
KITS AND ACCESSORIES
KIT CONTENTS
1 ea. UZY-6-B Blower Assembly
1 ea. Mill-Pack
1 ea. Instruction Sheet
TOOLS NEEDED
Robertson (square) or Phillips (star) screwdriver
INSTALLATION INSTRUCTIONS FOR INSTALLING UZY-6-B REPLACEMENT BLOWER KIT
FOR USE WITH WOOD-BURNING FIREPLACES LISTED IN TABLE 1
Blower Kit
Cat. No. Model Where Used
J8003 UZY-6-B Ladera™, Brentwood™ LV, WRT3820WS, WRT4820WS,
BIS® Nova and BIS Ultima
Table 1
INSTALLATION INSTRUCTIONS
Step 1. Open door, and remove the andirons, using a square or phillips
screwdriver. Then remove front and bottom refractories.
Step 2. Unscrew the access plate located in the firebox floor (12 screws).
Remove the access plate and the high heat cement used to seal it.
Step 3. Unplug the blower from the electric receptacle located on the
right side of the fireplace.
Step 4. Unscrew the blower using a Robertson (square) or Phillips
(star) screwdriver. The location of the (2) screws depends on
the version of the blower installed (see Figure 1). They can be
at each end of the support bracket close to the floor (Version B)
or on top of the support bracket near the left side (Version A).
See Figure 1.
Step 5. Take the blower out of the fireplace through the access opening.
Figure 1
WARNING
The blower must be plugged directly into a properly grounded
three-prong receptacle, 120 VAC, 60 Hz, single phase. Do not
cut or remove the grounding prong from this plug.
Installation must be in accordance with National Electrical
Code, ANSI/NFPA 70 - latest edition. In Canada, the current
CSA C22.1 Canadian Electrical Code - latest edition.
GENERAL INFORMATION
This blower kit can easily be installed when the fireplace has a pre- installed
junction box with 3 prong receptacle. You just have to plug it in.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact your local distributor
or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
Version A Unscrew these
two screws
Version B
Or these screws
to remove the blower
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
2
Figure 2
Figure 3
Installing the new Blower
Step 6. Insert the new blower in the fireplace. Since the new support
bracket is bigger, insert the blower into the access opening with
the back side down, sliding it backward in the fireplace and
rotating it up counterclockwise into position (see Figure 2).
Finishing the installation
Step 10. Plug the blower back in the electrical receptacle.
Step 11. Apply new high temperature sealant (Mill-Pack, included) to seal
the access plate, making a 1/4” bead covering all (12) screw
holes of the access opening.
Step 12. Reinstall the access plate and secure to the back of the firebox floor
using the (7) 10-32x1/2” screws supplied.
Step 13. Reinstall the front and bottom refractories and the andirons.
3 - Rotate counterclock-
wise into position
Step 9. Screw in through these holes to the fireplace back.
By offsetting the blower 4” to the right, this spacer
will be centered in the fireplace.
2 - Slide the blower to the
back of the fireplace
1 - Insert the blower
backside down
Steps 7 and 8 apply if the blower you removed is an older version.
Otherwise goto step 9.
Step 7. There are two 1” spacers left after removing the old blower.
Leave them there because they are riveted, although they won’t
be used anymore.
Step 8. Position the blower so that the new 1” spacer is touching the
back of the fireplace and the blower is offset about (4) inches to
the right (so the motor of the blower is not under the firebox).
Step 9. Screw the blower in place using the supplied (4) black self-tapping
screws through the holes of the 1” spacer and securing through
the fireplace back (see Figure 3, step 9).
r
.
Reinstall these (2) screws
into the 1” spacer.
Innovative Hearth Products reserves the right to make changes at any time,
without notice, in design, materials, specifications, prices and also to discon-
tinue colors, styles and products. Consult your local distributor for fireplace
code information.
Printed in U.S.A. © 2015 Innovative Hearth Products
P/N 900597-00 Rev. NC 10/2015 1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Astria Fireplaces WRT3820 Instruction Sheet

Astria Fireplaces
Brand
Astria Fireplaces
Model
WRT3820
Category
Fireplaces
Type
Instruction Sheet
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents