Troy-Bilt 21A682J766 User manual

Brand: Troy-Bilt

Model: 21A682J766

Category: Mini tillers

Type: User manual

This manual is also suitable for

TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Printed In USA

OperatOr’s Manual

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

Rear-Tine Tiller — Model 682

Form No. 769-03557

(November 6, 2007)

Customer Support

Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of

this machine, you can seek help from the experts. Choose from the options below:

Visit us on the web at www.troybilt.com

Call a Customer Support Representative at (800) 828-5500 or (330) 558-7220

Write us at Troy-Bilt LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019

◊

Thank you for purchasing a Garden Tiller manufactured by

Troy-Bilt LLC. It was carefully engineered to provide excellent

performance when properly operated and maintained.

Please read this entire manual prior to operating the equipment.

It instructs you how to safely and easily set up, operate and

maintain your machine. Please be sure that you, and any other

persons who will operate the machine, carefully follow the

recommended safety practices at all times. Failure to do so could

result in personal injury or property damage.

All information in this manual is relative to the most recent

product information available at the time of printing. Review

this manual frequently to familiarize yourself with the machine,

its features and operation. Please be aware that this Operator’s

Manual may cover a range of product specifications for various

models. Characteristics and features discussed and/or illustrated

in this manual may not be applicable to all models. Troy-Bilt LLC

reserves the right to change product specifications, designs and

equipment without notice and without incurring obligation.

This product has met the rigid safety standards of the Outdoor

Power Equipment Institute and an independent testing

laboratory. If you have any problems or questions concerning the

machine, phone a authorized Troy-Bilt service dealer or contact

us directly. Troy-Bilt’s Customer Support telephone numbers,

website address and mailing address can be found on this page.

We want to ensure your complete satisfaction at all times.

Throughout this manual, all references to right and left side of the

machine are observed from the operating position

The engine manufacturer is responsible for all engine-related

issues with regards to performance, power-rating, specifications,

warranty and service. Please refer to the engine manufacturer’s

Owner’s/Operator’s Manual, packed separately with your

machine, for more information.

Thank You

Record Product Information

Before setting up and operating your new equipment, please

locate the model plate on the equipment and record the

information in the provided area to the right. You can locate the

model plate by standing at the operator’s position and looking

down at the rear of the deck. This information will be necessary,

should you seek technical support via our web site, Customer

Support Department, or with a local authorized service dealer.

MOdel nuMber

serial nuMber

To The Owner

Safe Operation Practices ........................................ 3

Assembly & Set-Up .................................................. 6

Controls & Features ................................................12

Operation ................................................................13

Maintenance & Adjustments ................................ 25

Service .................................................................... 37

Troubleshooting .................................................... 40

Replacement Parts ................................................ 42

Table of Contents

Important Safe Operation Practices

Training

Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place for

future and regular reference and for ordering replacement

parts.

Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them

quickly.

Never allow children under 14 years of age to operate this

machine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the machine and be trained and supervised by an

adult.

Never allow adults to operate this machine without proper

instruction.

Keep the area of operation clear of all persons, particularly

small children and pets. Stop machine if anyone enters the

area.

Preparation

Thoroughly inspect the area where the equipment is to

be used. Remove all stones, sticks, wire, and other foreign

objects which could be tripped over and cause personal

injury.

Wear sturdy, rough-soled work shoes and close fitting

slacks and shirt. Loose fitting clothes or jewelry can be

caught in moving parts. Never operate this machine in bare

feet or sandals.

Disengage clutch levers and shift (if provided) into neutral

(“N”) before starting the engine.

Never leave this machine unattended with the engine

running.

Never attempt to make any adjustments while engine is

running, except where specifically recommended in the

operator’s manual.

Safe Handling of Gasoline:

To avoid personal injury or property damage use extreme care

in handling gasoline. Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury can occur when

gasoline is spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

Use only an approved gasoline container.

Never fill containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place

containers on the ground away from your vehicle

before filling.

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in this manual before attempting to operate this machine. Failure to comply

with these instructions may result in personal injury.

When you see this symbol. HEED ITS WARNING!

DANGER! This machine was built to be operated according to the safe operation practices in

this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. This machine is capable of amputating fingers, hands,

toes and feet. Failure to observe the following safety instructions could result in serious

injury or death.

CALIFORNIA PROPOSITION 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects

or other reproductive harm.

WARNING! Battery posts, terminals, and related accessories contain lead and lead

compounds, chemicals known to the State of California to cause cancer and reproductive

harm. Wash hands after handling

4 sectiOn 2 — iMpOrtant safe OperatiOn practices

After striking a foreign object, stop the engine, disconnect

the spark plug wire and ground against the engine.

Thoroughly inspect the machine for any damage. Repair

the damage before starting and operating.

Disengage all clutch levers (if fitted) and stop engine

before you leave the operating position (behind the

handles). Wait until the tines come to a complete stop

before unclogging the tines, making any adjustments, or

inspections.

Never run an engine indoors or in a poorly ventilated area.

Engine exhaust contains carbon monoxide, an odorless

and deadly gas.

Muffler and engine become hot and can cause a burn. Do

not touch.

Use caution when tilling near fences, buildings and

underground utilities. Rotating tines can cause property

damage or personal injury.

Do not overload machine capacity by attempting to till soil

too deep at too fast of a rate.

If the machine should start making an unusual noise or

vibration, stop the engine, disconnect the spark plug wire

and ground it against the engine. Inspect thoroughly for

damage. Repair any damage before starting and operating.

Keep all shields, guards, and safety devices in place and

operating properly.

Never pick up or carry machine while the engine is running.

Use only attachments and accessories approved by the

manufacturer. Failure to do so can result in personal injury.

If situations occur which are not covered in this manual, use

care and good judgement. Contact Customer Support for

assistance and the name of you nearest servicing dealer..

Maintenance & Storage

Keep machine, attachments and accessories in safe

working order.

Allow a machine to cool at least five minutes before

storing. Never tamper with safety devices. Check their

proper operation regularly.

Check bolts and screws for proper tightness at frequent

intervals to keep the machine in safe working condition.

Also, visually inspect machine for any damage.

Before cleaning, repairing, or inspecting, stop the engine

and make certain the tines and all moving parts have

stopped. Disconnect the spark plug wire and ground it

against the engine to prevent unintended starting.

Do not change the engine governor settings or over-speed

the engine. The governor controls the maximum safe

operating speed of engine.

Maintain or replace safety and instruction labels, as

necessary.

Follow this manual for safe loading, unloading,

transporting, and storage of this machine.

Always refer to the operator’s manual for important details

if the machine is to be stored for an extended period.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the ground.

If this is not possible, then refuel such equipment on

a trailer with a portable container, rather than from a

gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

Never fuel machine indoors.

Never remove gas cap or add fuel while the engine

is hot or running. Allow engine to cool at least two

minutes before refueling.

Never over fill fuel tank. Fill tank to no more than ½

inch below bottom of filler neck to allow space for

fuel expansion.

Replace gasoline cap and tighten securely.

If gasoline is spilled, wipe it off the engine and

equipment. Move unit to another area. Wait 5

minutes before starting the engine.

To reduce fire hazards, keep machine free of grass,

leaves, or other debris build-up. Clean up oil or fuel

spillage and remove any fuel soaked debris.

Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

as on a water heater, space heater, furnace, clothes

dryer or other gas appliances.

Operation

Do not put hands or feet near rotating parts. Contact with

the rotating parts can amputate hands and feet.

Do not operate machine while under the influence of

alcohol or drugs.

Never operate this machine without good visibility or light.

Always be sure of your footing and keep a firm hold on the

handles.

Keep bystanders away from the machine while it is in

operation. Stop the machine if anyone enters the area.

Be careful when tilling in hard ground. The tines may catch

in the ground and propel the tiller forward. If this occurs,

let go of the handle bars and do not restrain the machine.

Exercise extreme caution when operating on or crossing

gravel surfaces. Stay alert for hidden hazards or traffic. Do

not carry passengers.

Never operate the machine at high transport speeds on

hard or slippery surfaces.

Exercise caution to avoid slipping or falling.

Look down and behind and use care when in reverse or

pulling machine towards you.

Start the engine according to the instructions found in this

manual and keep feet well away from the tines at all times.

10.

5sectiOn 2 — iMpOrtant safe OperatiOn practices

If the fuel tank has to be drained, do this outdoors.

Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

Notice Regarding Emissions

Engines which are certified to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certified to operate on regular unleaded gasoline, and

may include the following emission control systems: Engine

Modification (EM) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING! This machine is equipped with an

internal combustion engine and should not be used

on or near any unimproved forest-covered,

brushcovered or grass-covered land unless the

engine’s exhaust system is equipped with a spark

arrester meeting applicable local or state laws (if

any).

If a spark arrester is used, it should be maintained in effective

working order by the operator. In the State of California the

above is required by law (Section 4442 of the California Public

Resources Code). Other states may have similar laws. Federal laws

apply on federal lands.

A spark arrester for the muffler is available through your

nearest engine authorized service dealer or contact the service

department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

10.

Average Useful Life

According to the Consumer Products Safety Commission

(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an Average Useful Life of seven (7) years, or 130

hours of operation. At the end of the Average Useful Life, buy

a new machine or have the machine inspected annually by an

authorized service dealer to ensure that all mechanical and

safety systems are working properly and not worn excessively.

Failure to do so can result in accidents, injuries or death.

WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

WARNING! To prevent personal injury or property

damage, do not start the engine until all assembly

steps are complete and you have read and

understand the safety and operating instructions in

this manual.

Resommended Tools for Assembly

⁄” open-end wrench (1)

⁄” open-end wrench (2)

⁄” open-end wrench (2)

⁄” open-end wrench (1)

⁄” open-end wrench (1)

Flat blade screwdriver (1)

Scissors (to trim plastic ties)

Tire pressure gauge (1)

4-⁄” high wood block to prop machinne

Contents of Hardware Pack

26 oz. Bottle SAE 30W Oil (1)

Clutch Pawl Spring (1)

Belt Adjusting Tool (1)

Plastic Cable Ties (2)

Curved Head Screw, ⁄-20 x 2 (1)

Flanged Lock Nut, ⁄-20 (1)

Pan Head Screw, #10-32 x ⁄ (1)

The following parts (electric start models only), packaged

separately.

Nuts, ⁄-20 for battery terminals (2)

Screws, ⁄-20 x ⁄ for battery terminals (2)

Keys in ignition switch (2)

Assembly

Unpacking Instructions

NOTE: Do not severely bend any of the control cables on the

tiller.

The tiller is heavy. Do not attempt to remove it from

the shipping platform until instructed to do so in these

assembly steps.

Remove all unassembled parts from the carton. The

hardware bag is included in your literature packaging.

•

Check that you have the items listed above (contact your

local dealer or the Factory if any items are missing or

damaged).

Handle

NOTE: When disassembling the handlebar assembly, keep the

left-side clamp and ratchet separated from the right-side clamp

and ratchet.

Disassemble the handlebar assembly. To do this, remove

the height adjustment lever by turning the lever in a

counterclockwise direction. See Fig. 3-1.

Place the handlebar ends on either side of the base, with

the wire harness toward the rear of the base See Fig. 3-1.

Install the height adjustment lever through the right-side

clamp, handlebar end, ratchet, and base; then out through

the left-side ratchet, handlebar end, and clamp. See Fig.3-1.

Secure with the nut, but do not fully tighten.

NOTE: Do not force the height adjustment lever through

the handlebars. The interlock wires may be blocking the

lever and could be damaged. You may gently move the

wires aside if this condition occurs.

Raise the handlebars to one of two height settings and

tighten the height adjustment lever. Also, make sure all

other mounting hardware is securely tightened.

Contents of Carton

One Tiller • One Handlebar Support• One Handlebar Assembly•

One Hardware Pack• One Wheels/Tines PTO Lever• One Operator’s Manual•

Height

Adjustment

Lever

Right

Clamp

Handlebars

Right

Ratchet

Left

Ratchet

Base

Left

Clamp

Nut

Wire Harness

Base

Bolt

Figure 3-1

Assembly & Set-Up

Moving the Tiller off the Shipping Platform

Set the Depth Regulator Lever to travel position. Do this

by lifting the tiller by the handlebars, then pulling straight

back on the lever and sliding down to the highest notched

setting. See Fig. 3-2.

Set the Wheel Speed Lever to the Freewheel position. To

do this, move the lever approximately halfway between

the Fast and Slow settings while you rock the tiller forward

and backward until the wheels move freely. See Fig. 3-2

Lift the Handlebars high enough to clear the tiller tines

and pull back firmly to dislodge the tiller from the platform

wheel wells.

Wire Harness

Ground the green (and red for electric start tillers) wire(s) to

the engine block. See Fig. 3-3.

Connect the safety wire assembly (green and yellow wires).

See Fig. 3-4.

Connect the tiller’s main harness connection to the neutral

safety switch receptacle. See Fig. 3-5.

Depth

Regulator

Lever

Wheel

Speed

Lever

Figure 3-2

Figure 3-3

Figure 3-4

Figure 3-5

7sectiOn 2 — asseMbly & set-up

Wheels/Tines PTO Drive Lever

Loosen the bolt on the handlebar base and swing the

handlebars out to the right side. See Fig. 3-1.

Remove both sets of nuts, star washers, screws, and one

bushing from the yoke plates. See Fig. 3-6. There is a

bushing inside the short link. Be careful not to lose it when

removing screw.

Slide the plates at the end of the Wheels/Tines/PTO Lever

over the yoke plates. See Fig. 3-7. To aid in the next step,

insert a screw temporarily into the forward most holes of

the yoke plates and the lever.

Align the rear most holes of the yoke plates and the

Wheels/Tines PTO Lever. Use long nose pliers to hold the

bushing in place while inserting the screw through the

lever and yoke plates. See Fig. 3-8. Install the star washer

and the nut then hand tighten.

Retrieve the clutch pawl spring from hardware bag.

Remove the temporary screw from the forward holes

inserted in Step 3 and move the Wheels/Tines/PTO Lever

fully forward. Install the wider hook end of the clutch pawl

spring down into the small hole at the end of the handle.

Use pliers to insert the other end into the hole in the long

link bar. See Fig. 3-9.

NOTE: Do not bend or over stretch the spring while

installing.

Bushing

Yoke Plates

Screw

Nut

Star Washers

Short Link

Long Link

Figure 3-6

Plates

Wheel

Speed

Lever

Forward Hole

Wheels/Tines/PTO

Drive Lever

Figure 3-7

Bushing

Screw

Star

Washer

Nut

Figure 3-8

Clutch

Pawl

Spring

Long

Link

Bar

Figure 3-9

8 sectiOn 2— asseMbly & set-up

Pull the Wheels/Tines/PTO Lever back to align the forward

most holes in the yoke plate with the holes in the lever

plates. Also align the bushing that is inside the short link

bar. Install the screw, star washer, and nut, then tighten

securely. Securely tighten all other hardware. Also ensure

that the spring is properly seated at both ends. Completed

assembly should appear as illustrated in Fig. 3-10.

Test the operation of the Wheels/Tines/PTO Lever. Push the

lever down until it engages in the Forward position. The

clutch roller must rest beneath the adjustment block. Next,

move the lever up to the Neutral position. See Fig. 3-11.

To test Reverse, lift and hold the lever all the way up in

the Reverse position, then let it go. The lever should

automatically return to the Neutral position. See Fig.

3-12. If not, do not use the tiller. See your local authorized

dealer or call the Factory Technical Service Department for

instructions.

Forward Hole

Short Link Bar

Clutch Pawl Spring

Figure 3-10

Clutch Roller

Adjustment Block

Figure 3-11

Clutch Roller

Adjustment Block

Figure 3-12

9sectiOn 2 — asseMbly & set-up

Engine Throttle Lever and Cable

For shipping purposes, the throttle cable, together with the

throttle lever, is wound around the engine. Carefully unwind

the cable. If the throttle control label is covered with a clear

protective coating, peel it off.

WARNING! To avoid electric shock from a short

circuit (electric start tillers only), never allow the

throttle cable to touch the battery. Route the cable

below the battery, on the outside of the battery

holder.

To attach the throttle lever and cable:

Run the throttle cable up the inside edge of the right

handlebar and position the lever as shown in Fig. 3-13.

From the outside of the handlebar, insert the curved head

screw, through the handlebar and the center hole in the

throttle lever mounting bracket. See Fig. 3-13.

Loosely install the flanged lock nut and move the throttle

lever back to the STOP position.

From the lever side of the bracket, thread a pan head screw

through the small hole in the throttle lever bracket and

into the handlebar. Tighten the screw securely.

Securely tighten both the flanged lock nut and the curved

head screw.

Use two plastic ties to secure the throttle cable to the

right handlebar in two places. Loop each tie around the

handlebar and cable (serrated side faces in) and pull the

ties tight. Trim the ends.

Electric Start System (If Equipped)

The following steps explain how to install and charge the battery

on electric start tillers. For your safety, follow all steps and

observe all accompanying safety messages. The Maintenance &

Adjustments section contains other general battery maintenance

and recharging instructions.

WARNING! Battery produces explosive gases. Keep

away sparks, flames, and cigarettes. Ventilate area

when charging or using battery in an enclosed

space. Make sure battery vent tube is always open

after battery is filled with acid.

WARNING! Remove metal jewelry before working

near the battery or near the electrical system. Failure

to comply may cause a short circuit, resulting in

electrical burns, a shock, or battery gas explosion.

NOTE: If the battery is put into service after the date shown on

the top of the battery, charge for a minimum of one hour at 6-10

amps. Refer to the Maintenence & Adjustments section of this

manual for more detailed instructions regarding proper battery

charging procedure.

WARNING! Never jump start the battery with a

vehicle battery or charging system. This may

produce a battery explosion, causing acid or

electrical burns.

Before installing the battery and its hold-down clamp,

insert the plastic wire harness receptacle into the prongs

of the keyswitch located on the hold-down clamp. See Fig.

3-14.

Remove the ignition keys from the keyswitch and store

them safely away. Do not insert the key into the keyswitch

until you complete this section and read the Operation

section. See Fig. 3-14.

Pan Head

Screw

Curved Head

Screw

Figure 3-13

Screw

Negative

Battery

Post

Negative

Battery

Cable

Black

Rubber

Boot

Nut

Keyswitch

Harness

Receptacle

Selenoid

Black

Rubber

Boot

Positive

Battery

Cable

Positive

Battery

Post

Figure 3-14

10 sectiOn 2— asseMbly & set-up

Use a ⁄” long screw and ⁄-20 hex nut to connect the

positive (+) battery cable to the positive (+) battery post.

Make sure that this is the cable on the left side, with one

end attached to the solenoid. See Fig 3-14.

WARNING! To Avoid Personal Injury or Property

Damage: Do not touch the positive battery terminal

and any surrounding metal objects with tools,

jewelry or other metal items. Failure to comply could

cause a short circuit leading to electrical burns or an

explosion of battery gases. Never bring a gas can

near the positive (+) battery terminal. A short circuit

could occur leading to an explosion of the gasoline

or the battery gases. Always fill the engine fuel tank

from the front or side of the engine.

Slide the black rubber boot completely over the battery

post and cable connector. See Fig. 3-14.

Use a ⁄” long screw and ⁄-20 hex nut to connect the

negative (-) battery cable to the negative (-) battery post

and secure with screw and nut. See Fig. 3-14.

Slide the black rubber boot completely over the battery

post and cable connector. See Fig. 3-14.

Set-Up

Tires

For shipping purposes, the tires may be overinflated. Check the

air pressure in each tire and adjust them to between 10 and 20

pounds per square inch. You must inflate each tire to equal air

pressures to prevent the tiller from pulling to one side.

Gas & Oil Fill-Up

Service the engine with gasolina and oil as instructed in the

Engine Operator’s Manual packed seperately with your tiller.

Read the instructions carefully.

WARNING! Use extreme care when handling

gasoline. Gasoline is extremely flammable and the

vapors are explosive. neve fuel the machine indoors

or while the engine is hot or running. Extinguish

cigarettes, cigars, pipes and any other sources of

ignition.

Transmission Gear Oil

The transmission was filled with gear oil at the factory. However,

be sure to check the oil level at this time to make certain it

is correct. See the Maintenance & Adjustments section for

instructions on checking and adding transmission gear oil.

11sectiOn 2 — asseMbly & set-up

Handlebar Height

Adjustment Lever

Wheels/Tines/PTO

Drive Lever

Forward

Interlock

Levers

Depth Regulator

Lever

Wheel Speed Lever

Tines/PTO Clutch Lever

Figure 4-1

Tiller controls and features are described below and illustrated in

Fig. 4-1.

WARNING! Be familiar with all the controls and

their proper operation. Know how to stop the

machine and disengage it quickly.

NOTE: For detailed information on all engine controls refer to the

seperate Engine Operator’s Manual.

Wheels/Tines/PTO Drive Lever

Use the Wheels/Tones/PTO Drive Lever to engage and disengage

power to the transmission.

Forward Interlock Levers

The Forward Interlock Levers are attached under the handlebar

grip and will stop the engine if both levers are released.

Wheel Speed Lever

The Wheels speed lever controls the speed at which the wheels

spin.

Tines/PTO Clutch Lever

The Tines/PTO Clutch Lever is used to engage or disengage

power to the transmission.

Depth Regulator Lever

The Depth Regulator Lever is used to regulate the tilling depth

of the tines.

Handlebar Height Adjustment Lever

The Handlebar Height Adjustment Lever is used to adjust the

handlebars to one of two heights.

Engine Throttle Lever

Use the throttle lever to adjust engine speed as well as to start

and stop the engine.

Keyswitch Starter

The keyswitch starter on electric start models is used to start, run

and stop the tiller.

Controls and Features

Starting the Engine

The following steps describe how to start and stop the engine.

NOTE: Do not attempt to engage the tines, wheels, or any PTO

attachment until you have read all of the operating instructions

in this section.

Pre-Start Checklist

Make the following checks and perform the following services

before starting the engine.

Read the Safe Operation Practices and Features & Controls

sections in this Manual. Read the separate Engine

Operator’s Manual.

Check the tiller for loose or missing hardware. Service as

required.

Check the engine oil level. See Engine Operator’s Manual.

Shift the Wheels/Tines/PTO Drive lever into NEUTRAL

position. See the Controls and Features section for more

information on this lever.

Check the safety guards. All guards and covers must be

securely in place.

Check the air cleaner. See the Engine Operator’s Manual.

Attach the spark plug wire to spark plug.

Check Engine Cooling System. Clear cooling fins and air

intake screen of debris. See the Engine Operator’s Manual.

Select High/Low Belt Speed range.

Adjust the Handlebar Height.

Fill the fuel tank with gasoline in accordance with the

directions in the separate Engine Operator’s Manual.

Follow all instructions and safety rules carefully.

WARNING! Never run the engine indoors or in an

enclosed, poorly ventilated are. Engine exhaust

contains carbon monoxide, an odorless and deadly

gas. Avoid engine muffler and nearby areas.

Temperatures in these areas may exceed 150° F.

NOTE: After the first two hours of operation, perform the

maintenance procedures shown in the Maintenance Schedule in

the Maintenance & Adjustments Section of this manual.

Starting the Engine

With the engine off, place the Wheels/Tines/PTO Drive

Lever in the NEUTRAL position. If in the FORWARD position,

tap the lever sharply upward, it should automatically move

into NEUTRAL position.

Put the Depth Regulator Lever in the Travel position (lever

all the way down) so that the tines are off the ground. To do

this, lift up on the handlebars, pull the lever back, and push

it down all the way to the top detent (notched) position.

Move the Wheel Speed Lever to either the SLOW or FAST

position. Be sure to roll the wheels while shifting the lever

until the wheels engage.

10.

11.

NOTE: If using a PTO stationary attachment, move the

Wheel Speed Lever into FREEWHEEL and block the wheels

to prevent the equipment from moving. See Fig. 4-1.

Move the Tines/PTO Clutch Lever into DISENGAGE position.

NOTE: Use the ENGAGE position if you want the tines

to revolve or to apply power to a PTO-driven stationary

attachment.

If the engine is equipped with a fuel valve, turn the valve

to the OPEN position as instructed in the separate Engine

Operator’s Manual.

If the engine is equipped with an ON/OFF switch, move the

switch to ON. Move engine throttle lever away from STOP.

Choke or prime the engine as instructed in the separate

Engine Operator’s Manual.

If not equipped with an electric start system, place one

hand on the fuel tank to stabilize the tiller when you pull

the recoil starter rope.

If equipped with an electric start system, turn the key to

START position to crank the engine then release when the

engine starts. If the engine does not start right away, do

not hold the key at START for more than a few seconds.

Release then try again after a short pause. Damage to

the starter motor can occur if it is cranked more than 15

seconds per minute.

If the engine does not start after a number of tries, refer to

the Engine Operator’s Manual for specific instructions.

When the engine starts, move the Throttle Lever to the

SLOW position and then gradually move the choke lever

(on engines so equipped) to OFF or RUN position.

Move the throttle speed control to FAST setting when

tilling.

10.

11.

Blocks

Figure 4-1

Operation

Starting Electric Start Engine with Recoil Starter

You may, at some point, have to start an electric start engine

with the recoil starter rope. Before attempting to do so, perform

the following applicable steps:

If you suspect the battery charge is weak, and there is no

visible damage. Disconnect the cables from the battery

and clean both cable terminals, and the battery posts

in accordance with the instructions provided in the

Maintenance & Adjustments section. Reconnect the cables

and securely tighten to the battery posts. The engine will

recharge the battery if the battery is still good.

If you suspect the batter is “dead”, or if the battery is

damaged, disconnect, and remove it. Have it checked by a

qualified technician.

If the battery has been removed, wrap the cable terminals

at the end of the positive cable with electrical tape and

secure the cable to the battery bracket. This will prevent

electrical discharge.

Before pulling the recoil starter rope, turn the keyswitch

to the RUN position. Move the Throttle Lever away from

the STOP position and set the choke as applicable. See the

Engine Operator’s Manual.

Cold Weather Operation

When temperatures fall below 40º F, do the following steps to

protect your engine and transmission from damage:

Refer to the Engine Operator’s Manual for the motor oil

specifications for cold weather operation.

Use winter blend gasoline.

Warm the engine up before putting it under a load.

Use the correct weight gear oil in the PTO Power

transmission.

Warm up the transmission gear oil as follows:

With the engine running, move the Wheel Speed

Lever to FREEWHEEL (then block the wheels so they

can’t roll).

Put the Tines/PTO Clutch Lever into DISENGAGE,

then squeeze one of the Forward Interlock Levers

and shift the Wheels/Tines/PTO Drive Lever to

FORWARD.

If the wheels are frozen to the ground, melt the ice with

warm water.

Stopping the Engine and the Tiller

To stop the wheels and tines, move the Wheels/Tines/PTO

Drive Lever into NEUTRAL position and then release both

Forward Interlock Levers.

Move the engine Throttle Lever to the STOP position. Then

on electric start models, turn the key to OFF. Remove the

key for safekeeping.

NOTE: The engine may have a separate Throttle Control Lever

and ON/OFF switch on the engine. These controls can also be

used to stop the engine. See the Engine Operator’s Manual for

information specific to your engine.

•

Engaging the Drive & Tines

NOTE: This is a traditional standard-rotating-tine (SRT) tiller

with forward rotating tines. It operates in a completely different

manner than counter-rotating-tine (CRT) tillers, or from front-tine

tillers.

WARNING! To help avoid personal injury, be aware

that the tiller can unexpectedly bounce up or jump

ahead and propel away from you if the tines strike

hard or frozen ground, or buried obstacles like large

stones, roots or stumps.

Start the engine and gradually increase the engine speed

to FAST.

Test the Forward Interlock Safety System. See the Forward

Interlock System in the Maintenance & Adjusments section

for more information.

WARNING! The Forward Interlock Safety System is

designed for the operator’s safety. Do not

disconnect or attempt to defeat the purpose of the

system. If the system malfunctions, immediately

contact your local authorized dealer or the TROYBILT

Technical Service Department for assistance. Do not

use the tiller or the PTO power feature until the

Forward Interlock Safety System is functioning

properly.

When practicing, set the Depth Regulator Lever to Travel

position. Otherwise, set the Depth Regulator Lever to a

desired depth.

Move Tines/PTO Clutch Lever to ENGAGE position if you

want the tines to turn. If practicing, leave in DISENGAGE.

NOTE: Do not move Tines/PTO Clutch Lever to ENGAGE

unless Wheels/Tines/PTO Drive Lever is in NEUTRAL. Tiller

damage may occur.

To move the tiller forward and engage the tines, squeeze

and hold either Forward Interlock Lever against the

handlebar grip (See Fig. 4-2), then move the Wheels/Tines/

PTO Drive Lever down to FORWARD position.

Figure 4-2

14 sectiOn 5— OperatiOn

When the tiller moves forward, relax and let the wheels

power the tiller along while the tines dig. Walk behind

and to one side of the tiller. Walk on the side that is not yet

tilled. Use a firm grip on the handlebars but keep your arm

relaxed. See Fig. 4-3.

NOTE: Let the tiller move ahead at its own pace. Do not

push it ahead — this reduces operator control and tilling

efficiency. Do not push the handlebars down in an attempt

to dig deeper — this takes weight off the wheels, reduces

traction, and causes the tines to try to propel the tiller.

Stopping Forward Motion & Tines

To stop forward motion, tap Wheels/Tines/PTO Drive Lever

upward into NEUTRAL. Then release the Forward Interlock

Levers. The wheels and tines will stop and the engine will

continue running.

In an emergency, release all of the control levers. This stops

forward motion and shuts-off the engine.

Moving in Reverse

WARNING! To help avoid personal injury or

damage to the equipment be sure no obstacles are

behind you before operating the tiller in REVERSE.

Disengage the tines, reduce engine speed, and

move the Wheel Speed Lever to SLOW position

before operating in REVERSE. Avoid using FAST

wheel speed until you are familiar with backing the

tiller.

NOTE: Do not till while in REVERSE.

Shift the Tines/Wheels/PTO Drive Lever into NEUTRAL and

move the Wheel Speed Lever to the SLOW position.

Move the Tines/PTO Clutch Lever into DISENGAGE position.

Verify that the area behind you is clear.

Lift up the handlebars until the tines are off the ground,

then shift the Wheels/Tines/PTO Drive Lever all the way

up and hold. You do not need to squeeze the Forward

Interlock Levers to use reverse.

The tiller immediately engages in reverse. Periodically

check behind you while holding the handlebars up and the

Wheels/Tines/PTO Lever in its upper-most position.

Stopping Reverse Motion

Release the Wheels/Tines/PTO Drive Lever — the lever

automatically returns to the NEUTRAL position. This stops the

wheels immediately. The Forward Interlock Levers will not stop

REVERSE motion.

Turning the Tiller

Turning the tiller is easy and just requires practice. First find the

balance point between the engine and the tines by lifting up the

handlebars. See Fig. 4-4. Once you find the balance point, then

let the powered wheels do the turning as you push sideways on

the handlebars in the direction of the turn. Practice the turning

maneuver described here in a large open area. Once comfortable

turning the tiller, you can then take it to the garden area.

At the end of a row, move the Wheels/Tines/PTO Drive

Lever to NEUTRAL position and reduce the engine speed.

Move the Tines/PTO Clutch Lever into the DISENGAGE

position.

Resume forward operation, and lift the handlebars until

the tines are off the ground. Refer to Fig. 4-4. Find the

balance point between the engine and the tines. Then

push the handlebars in the direction of the turn. Be very

careful to keep feet and legs away from the tines — which

should be disengaged. Let the powered wheels do the

hard work.

NOTE: Use REVERSE if necessary to turn in a limited space.

When the turn is complete, shift to NEUTRAL and lower

the handlebars. Move the Tines/PTO Clutch Lever back to

ENGAGE position and resume forward operation.

Figure 4-3

Figure 4-4

15sectiOn 5 — OperatiOn

Choosing Wheel & Tine Speeds

The tiller has four FORWARD wheel/tine speed combinations for

handling a variety of tilling tasks and gardening jobs. Experiment

with the tine depth, engine speed, and wheel/tine speed to

determine the combination that provides the best results. Here

are some tips:

Advance the throttle lever so the engine has sufficient

power.

When tilling untilled or hard earth, do not set the Depth

Regulator too deep. The tiller will buck and the engine will

load down.

You will know your settings are ideal when the tines break-

up the soil easily, the engine does not labor, and your

progress is steady and smooth. See Fig. 4-5.

Changing Belt speed

Your tiller has two belt-driven speed ranges — HIGH RANGE and

LOW RANGE — you pick one or the other by deciding which set

of pulley grooves to move the forward belt into. By moving the

belt from one speed range into the other, in combination with

the FAST and SLOW wheel speeds, you obtain a choice of four

different forward wheel speeds and two different tine speeds.

WARNING! To help avoid serious personal injury,

stop the engine, remove the ignition key, disconnect

spark plug wire and move the wire away from the

spark plug and let engine and muffler cool down

before changing the belt speeds.

Changing the belt from LOW range into HIGH range (or back

again) is a matter of moving the belt from one set of pulley

grooves to a second set of pulley grooves. This change is done

quickly and without tools.

WHEEL SPEED AND BELT RANGE SELECTION GUIDE

SLOW GEAR, LOW BELT RANGE

For:

Tilling in sod.

Tilling in hard clay.

Tilling under standing

cornstalks in tough soil

conditions.

Tilling under cover crops.

Preparing a deep

seedbed.

Tilling in stony soil.

Tilling under residues

and organic matter.

Mixing in fertilizers,

manure.

SLOW GEAR, HIGH BELT RANGE

For:

Tilling in sod or hard clay.

Tilling under standing

cornstalks (slow, steady

speed allows time to

shred stalks).

Tilling under cover crops

(best wheel speed and

belt speed range in most

soils).

Preparing seedbeds

(best speed choice in

most soils).

Tilling in stony ground.

Building raised garden

beds.

Mixing in fertilizer.

Using tiller wings in hard

soil.

Mixing fertilizer and

manure.

Tilling residues and

organics.

10.

FAST GEAR, LOW BELT RANGE

For:

Going over seedbed

for the last time before

planting crops.

Covering over seeds in

wide row or plot planting

(lift handlebars to avoid

going too deep).

Hilling and furrowing.

Making raised beds.

Cultivating (lift

handlebars to avoid

going too deep).

Tilling large areas.

Tilling organic matter in.

Cultivating between

raised beds with

optional hiller/furrower

attachment.

FAST GEAR, HIGH BELT RANGE

For:

Preparing seedbeds for

planting.

Covering seeds with

less need to hold up the

handlebars.

Cultivating (tiller travels

faster, rides higher on

the soil; allows engine

RPM to be reduced;

handlebars don’t have to

be raised).

Keeping large areas tilled

and cultivated in the

summer.

Tilling organic matter

under.

Moving tiller quickly.

Cultivating between

raised beds using the

optional hiller/furrower.

When the tiller is moving in REVERSE, the wheels are

you have only two reverse speeds SLOW and FAST, as set with

the Wheel Speed Lever.

Fig. 4-6 shows the range of wheel and tine speeds available

when using the two belt speed ranges and the FAST and SLOW

selections on the Wheel Speed Lever.

Figure 4-6

Available wheel and tine speeds at 3000 RPM engine speed.

Belt

Position

Wheel Speed

Lever

Wheel Speed Tine

Speed

Low Range Slow .5 MPH 146RPM

Low Range Fast 1.2 MPH 146RPM

High Range Slow .7 MPH 200RPM

High Range Fast 1.72 MPH 200RPM

Figure 4-5

16 sectiOn 5— OperatiOn

Changing Belt From Low Range to High Range

To avoid personal injury, shut off the engine, let all moving

parts come to a complete stop, then disconnect the spark

plug wire from the spark plug and move the wire away

from the spark plug before making any adjustments. Wait

for the engine and muffler to cool down.

Move the Wheels/Tines/PTO Drive Lever into NEUTRAL.

WARNING! The HIGH speed belt range position

combined with a FAST wheel speed setting propels

the tiller at the fastest pace. Reduce the engine

throttle speed when starting out to help avoid

personal injury or property damage if using this

speed combination.

Kneel on the left side of tiller. To create belt slack, reach

over to the right side of the pulleys and push in at the

center of the belt with a finger. At the same time, use your

left hand to work the belt part-way onto the lower-front

transmission pulley groove. See Fig. 4-7.

Go to the other side of the tiller to finish seating the belt

onto the pulley groove.

Working from the left side of the tiller, work the belt as

much as possible onto the top-front engine pulley groove.

See Fig. 4-8.

Finish seating the belt from the right side of the tiller.

NOTE: Proper belt tension is important for good

performance. See the Maintenance & Adjustment Section

for instructions on adjusting belt tension.

NOTE: If extra belt slack is needed to move the belt, just

raise the Wheels/Tines/PTO Drive Lever up into REVERSE.

This lowers the engine pulley, and creates more slack.

Check both sides of the high range pulley grooves to verify

that the belt is properly seated.

Changing Belt From High Range to Low Range

To avoid personal injury, shut off the engine, let all moving

parts come to a complete stop, then disconnect the spark

plug wire from the spark plug and move the wire away

from spark plug before making any adjustments. Let

engine and muffler cool.

Move the Wheels/Tines/PTO Drive Lever into NEUTRAL.

Lower-Rear Groove

Lower-Front Groove

Belt

Figure 4-7

Top-Rear Groove

Top-Front Groove

Belt

Figure 4-8

17sectiOn 5 — OperatiOn

Stand on the left side of the tiller. Use your right hand to

hold the Wheels/Tines/PTO Drive Lever up into REVERSE

position. Use your left hand to move the belt off the

top-front engine pulley groove to top-rear engine pulley

groove. See Fig. 4-9.

Go to the right side of tiller and finish seating the belt.

Still holding the lever up in REVERSE position, and working

from the left side of the tiller, move the belt from the lower

front transmission groove to the lower rear transmission

groove.

Go to the right side of the tiller and finish seating the belt.

See Fig. 4-10.

Check that the belt is fully seated in the pulley grooves.

Check this from both sides of the tiller.

Clearing the Tines

The tines have a self-clearing action which helps to eliminate

most tangling of debris. However, occasionally dry grass,

stringy stalks or tough vines may become tangled. Follow these

procedures to help avoid tangling and to clear the tines, if

necessary.

To reduce tangling, set the Depth Regulator deep enough

to get maximum “chopping” action as the tines chop the

material against the ground. Also, try to till under crop

residues or cover crops while they are green, moist and

tender.

While power composting, try swaying the handlebars from

side to side (about 6” to 12”). This “fishtailing” action often

clears the tines of debris.

It may be necessary to remove the debris by hand (a

pocket knife will help you to cut away the material).

WARNING! Before clearing the tines by hand, stop

the engine, allow all moving parts to stop and

disconnect the spark plug wire. Failure to follow this

warning could result in personal injury.

Tilling Tips & Techniques

Let the Tiller Do the Work

While tilling, relax and let the wheels pull the tiller along

while the tines do the digging. Walk on the side that is not

yet finished to avoid making footprints in the freshly tilled

soil and lightly, but securely grip the handlebar with just

one hand. Refer to Fig. 4-3.

Avoid pushing down on the handlebars in an attempt to

force the tiller to dig deeper. Doing so takes the weight

off the powered wheels, causing them to lose traction.

Without the wheels helping to hold the tiller back, the

tines will attempt to propel the tiller — often causing

the tiller to skip rapidly across the ground. Sometimes,

slight downward pressure on the handlebars will help get

through a particularly tough section of sod or unbroken

ground, but in most cases this won’t be necessary.

Tilling Depths

Avoid trying to dig too deeply too quickly, especially when

busting sod or tilling soil that hasn’t been tilled for some

time. Use shallow depth settings (only an inch or two deep)

for the first passes through the garden area. With each

succeeding pass, adjust the depth regulator to dig another

inch or two deeper. Watering the garden area a few days

prior to tilling will make tilling easier, as will letting the

newly worked soil set for a day or two before making a

final, deep tilling pass.

When cultivating — breaking up the surface soil around

plants to help destroy weeds — use very shallow depth

settings to prevent injury to plants whose roots often grow

close to the surface. If needed, lift up on the handlebars

slightly to prevent the tines from digging too deeply.

Cultivating on a regular basis not only eliminates weeds,

it also loosens and aerates the soil for better moisture

absorption and faster plant growth.

•

Wheels/Tines/PTO Drive Lever

Top-Rear Gear

Top-Front Gear

Figure 4-9

Belt

Lower-Rear Groove

Lower-Front Groove

Figure 4-10

18 sectiOn 5— OperatiOn

Avoid Tilling Wet, Soggy Soil

Tilling wet soil often results in large, hard clumps of soil

that can interfere with planting. If time permits, wait

a day or two after heavy rains to allow the soil to dry

before tilling. Test the soil by squeezing it into a ball. If it

compresses too easily, it is too wet to till.

Avoid Making Footprints

When possible, walk on the untilled side of the tiller to

avoid making footprints in the freshly tilled soil. See FIg.

4-3. Footprints cause soil compaction that can hamper root

penetration and contribute to soil erosion. They can also

“plant” unwanted weed seeds back into the newly tilled

soil.

Suggested Tilling Patterns

When preparing a seedbed, go over the same path twice in

the first row, then overlap one-half the tiller width on the

rest of the passes. See Fig. 4-11.

•

When finished in one direction, make a second pass at

a right angle . See Fig. 4-12. Overlap each pass for best

results. In very hard ground it may take three or four passes

to thoroughly pulverize the soil.

If the garden size will not permit lengthwise and then

crosswise tilling, then overlap the first passes by onehalf a

tiller width, followed by successive passes at one-quarter

width. See Fig. 4-13.

•

Figure 4-13

Figure 4-11

Figure 4-12

19sectiOn 5 — OperatiOn

With planning, you can allow enough room between rows

to cultivate. Leave room for the hood width, plus enough

extra room for future plant growth. See Fig. 4-14.

Tilling on Slopes

If you must garden on sloping ground, please follow two very

important guidelines:

Till only on moderate slopes, never on steep inclines

where footing is difficult Review the safety rules in the Safe

Operation Practices section.

It is recommend that you till up and down slopes rather

than terracing. Tilling vertically on a slope allows maximum

planting area and also leaves room for cultivating.

NOTE: When tilling on slopes, be sure the correct oil level

is maintained in the engine (check every one-half hour

of operation). The incline of the slope will cause the oil to

slant away from its normal level and this can starve engine

parts of required lubrication. Keep the engine oil level at

the full point at all times.

Tilling up and down slopes:

To keep soil erosion to a minimum, be sure to add

enough organic matter to the soil so that it has good

moistureholding texture and try to avoid leaving footprints

or wheel marks.

When tilling vertically, try to make the first pass uphill

as the tiller digs more deeply going uphill than it does

downhill. In soft soil or weeds, you may have to lift the

handlebars slightly while going uphill. When going

downhill, overlap the first pass by about one-half the width

of the tiller.

NOTE: For the best results, use the HIGH belt range and

SLOW wheel speed lever position. See Changing Speed

Belts in this section for more information on changing to

high range.

•

Terrace Gardening:

When a slope is too steep or too short for vertical tilling,

it may be necessary to till across the slope and create

terraced rows. Terraces are rows that are cut into the side of

a slope, creating a narrow, but flat area on which to plant.

On a long slope, you can make several terraces, one below

the other.

Terraces should be only 2-to-3 feet wide. Digging too far

into the side of the slope will expose poor subsoil that is

unproductive for plants.

To create a terrace, start at the top of the slope and work

down. Go back and forth across the first row. See Fig. 4-15.

Each succeeding lower terrace is started by walking below

the terrace you’re preparing. For added stability of the

tiller, always keep the uphill wheel in the soft, newly tilled

soil. Do not till the last 12” or more of the downhill outside

edge of each terrace. This untilled strip helps prevents the

terraces from breaking apart and washing downhill. It also

provides a walking path between rows.

Tilling across slopes without terracing:

If vertical or terracing gardening aren’t practical for you,

then you can till laterally across a slope. We don’t really

recommend this method as it can create unsure footing

and invites soil erosion.

Study the terrain to make certain the slope is not too

Steep for safe tilling. If possible, make terraced rows or till

vertically.

•

Figure 4-14

12" UNTILLED

REPEAT

DOWNHILL

UPHILL

Figure 4-15

20 sectiOn 5— OperatiOn

Page is loading ...

Troy-Bilt 21A682J766 User manual

Brand: Troy-Bilt

Model: 21A682J766

Category: Mini tillers

Type: User manual

This manual is also suitable for

Download PDF

report

Troy-Bilt 21A682J766 User manual

This manual is also suitable for

Troy-Bilt 21A682J766 User manual

Related papers

Other documents