Charbroil 463831803 Owner's manual

Category
Barbecues & grills
Type
Owner's manual
Correct position of LP Tank and
Tank Wire Support Bracket
See Use & Care Manual for “Match Lighting Instructions” and to
perform the Burner Flame Check” and important safety
instructions before using.
Hang grease clip from center of grill bottom.
Use an empty soup can (not included) to hang
from grease clip.
Back of Grill
Items to Assemble:
1 Grease Clip
1 Tank Wire Support Bracket
1 LP Tank
LP tank is shipped empty. Fill and leak check before
attaching to grill and regulator.
CAUTION
!
Failure to install can in clip will cause hot grease
to drip from bottom of grill with risk of fire or
property damage.
Tank collar opening must face to front of cart
once tank is attached.
Failure to install tank correctly may allow gas
hose to be damaged in operation, resulting in
the risk of fire.
Items to Assemble:
1 Warming Rack
1 Cooking Grate
A
B
Insert pivot wire of Warming
Rack into Lid. Flex leg
wires to insert into Grill
bottom.
Place cooking grate
into grill bottom.
Leg wires on Warming Rack
must run underneath surface.
A
Qty: 2
463831803
Items to Assemble:
1 Vaporiser Bar
1 Grate
Items to Assemble:
2 Wheel Assemblies
2 Hitch Pins
2 Leg Extenders
Items to Assemble:
2 Leg Assemblies
1 Bottom Shelf
6 carriage Bolts
6 Wing Nuts
Qty: 6
Qty: 6
Place Bottom Shelf and Legs as shown.
After assembling tighten all Wing Nuts.
Right Side:
Attach 2 Carriage Bolts and Wing Nuts in
front and back.
Left Side:
Place 1 Carriage Bolt
and Wing Nut in upper hole only
Items to Assemble:
1 Right Shelf
4 Wing Screws
Qty: 4
Items to Assemble:
1 Sideburner
1 Sideburner Grate
1 Sideburner Knob
1 Wing Nut
Qty: 1
A
A
B
C
Place Sideburner into hole.
Attach Sideburner Valve Cup. Make
sure Sideburner Tube is inside of
valve. Tighten with Wing Nut.
Place Sideburner Knob and Grate
Correctly assembled Sideburner Tube in Valve
B
C
Attach long wire from beneath console
to electrode beneath Sideburner.
D
D
Item to Assemble:
1 Wire Shelf
1 Panel
2 Push Pins
Qty: 2
placing tabs into slots on Bottom Shelf.
Attach with push pins.
A
B
Assemble front panel first by
Place Wire Shelf in 3rd hole from top.
A
B
Push Vaporiser Bar
down onto rest in
Grill Bottom
Attach Wheels with Hitch Pins
Items to Assemble:
2 End Caps
1 Tool Holder
2 Carriage Bolt
2 Wing Nut
1 Tool Holder
Bracket
Qty: 2
1
9
12
11
10
9
8
5
6
7
1
2
3
4
Items to Assemble:
1 Grill Bottom with Control Panel
1 Heat Shield
4 Carriage Bolts
4 Wing Nuts
1 Condiment Basket
Qty: 4
Qty: 4
Hinge Pin
and Hitch Pin
Qty: 2
Qty: 2
Qty:2
Items to Assemble:
1 Grill Lid
2 Hinge Pins
2 Hitch Pins
1 Handle
2 Wing Nuts
1 Logo Plate
Note: Grill lid
style may vary.
Note: Shelf style may vary.
Qty: 1
Qty: 1
Qty: 2
• Press end caps into left legs.
Attach bracket to back of tool holder with one
wing screw.
• Place tool holder on legs and body inside
tool holder. Using left hole in rear of body
use carriage bolt and wing nut to secure
body, bracket and leg.
• Place frame into body as shown, secure frame,
body and leg with carriage bolt and wing
nut.
• Using center hole in front leg, secure
tool holder and body to leg with crown
screw.
1 Wing Screw, 1/2”
1 Crown Screw
1 Sideburner Body
1 Sideburner Frame
Frame
Body
Tool Holder
Tool Holder Bracket
End Cap
B
B
  • Page 1 1

Charbroil 463831803 Owner's manual

Category
Barbecues & grills
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI