STEREO A OUTS 1-2
LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL
0 0 0 0 0 010 10 10 10 10 10
LEVEL
LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL
LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL
PAN
PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN
PAN PAN PAN PAN PAN PAN PAN PANPAN PAN PAN PAN PAN PAN PAN
LEVEL
0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1
3 3 3 3 3 3 3 3 7 7 7 7 7 7 7 7
5 5 5 5 5 5 5 5
010
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10
10 10 10 10 10 10 10 10
2 2 2 2 2 2 2 2
4 4 4 4 4 4 4 4 8 8 8 8 8 8 8 8
6 6 6 6 6 6 6 6
10
STEREO B OUTS 3-4
STEREO CSTEREO D OUTS 5-6OUTS 7-8
CH 1 CH 1CH 2 CH 2CH 3 CH 3CH 4 CH 4CH 5 CH 5CH 6 CH 6CH 7 CH 7CH 8 CH 8
UNiK A
POWER
MTX-8800
U n i v e r s a l M i x e r
Page 3
FRONT PANEL
1. Power on/off
Press this button to turn the MTX-8800 on and off.
2. Power LED
The power indicator lights up when the MTX-8800 is powered on.
3. Level Control
For adjusting the input level at the respective stereo output at the rear panel. Turn the control
clockwise beyond the detent position to increase the level up to 12dB.
4. PAN Control
Positions the input signal between the left and right output of the respective zone. In mid-positon
the signal level is equal at both outputs.
1
2 3
4
MTX-8800
USE ONLY WITH 250V FUSE
115
STEREO D STEREO C STEREO B STEREO A
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5INPUT 6INPUT 7INPUT 8
OUTS 8 OUTS 7 OUTS 6 OUTS 5 OUTS 4 OUTS 3 OUTS 2 OUTS 1
CAUTION
RISK O F ELECT RIC SHO CK
DO NOT OP EN
!
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD. DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR
MOISTURE.
CAUTION -TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER
OR ANY SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
FUSE :
0.5A /110V~120V
0.25 A/220V~240V
AC INPUT
VOLTAGE:
110V~120V 60Hz
220V ~240V 50Hz
MADE I N TAIWAN
Serial No.:
REAR PANEL
6
5
8
7
5. Input Section
XLR inputs (balanced) for connecting audio units with line level outputs.
6. Output Section
There are total ZONE 1 ~ 4, each zone disposes of a stereo output (2xXLR, balanced) for left and
right. The PAN control directs the signal to the respective output.
Outputs STEREO A for PA Zone 1
Outputs STEREO B for PA Zone 2
Outputs STEREO C for PA Zone 3
Outputs STEREO D for PA Zone 4
7. Voltage Selector
Make sure this switch is properly set.
8. AC Input with fuse holder
Used to plug the supplied power cord in, only replace the fuse when the device is disconnected
from mains.
ZONE 1
ZONE 2
ZONE 3
ZONE 4