GE GCVH6800J5MR Owner's manual

0

ge.com

Safety Instructions ............. 2,3

Operating Instructions

Control Panels ...................... 4-6

Control Settings ....................... 7

Fabric Care Labels .................... 13

Features ........................... 8-10

Loading and Using the Washer .... 11, 12

Installation Instructions ..... 14-19

Drain Requirements .................. 17

Electrical Requirements ............... 17

Installing the Washer ............. 18, 19

Location of Your Washer ............. 15

Preparing to Install Your Washer ...... 14

Replacement Parts ................... 19

Rough-In Dimensions ................. 15

Unpacking Your Washer .............. 16

Water Supplg Requirements .......... 17

Troubleshooting Tips ......... 20-22

Consumer Support

Service Telephone Numbers . Back Cover

Warrantg (Canada) .................. 24

Warrantg (U.S.) ...................... 23

GBVH5140

GCVH6260

GCVH6600

GHDVH626

GHDVH670

WBVH5100

WBVH6240

WCVH6260

WCVH6600

WHDVH626

WHDVH660

WCVH6400

WBVH5200

Loveuses

La section fran_aisecommence 6/a page 25

Lovodor( s

La secci6n en espaHol empieza en /a p6gina 51

ENERGYSTAR

As an ENERGY STAR® partner,

GEhas determined that this

product meets the ENERGYSTAR®

guidelines for energg efficiencg.

Write the model and serial

numbers here:

Model #

Serial #

Youcon find them on a label onthe

sideof the washeE

175DI807P583 49-90315-2

IO-07JR

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

--^WARNING! Foryoursafe theinformationinthismanualmustbefollowedtominimizetberisk

of fire or explosion, electric shock, or to prevent property damage, personal injury or

loss of life.

Theinstructions in this manual and all other literature included with this washer are

not meant to cover every possible condition and situation that may occur. Good,safe

practices and caution MUSTbe applied when installing, operating and maintaining

any appliance.

WATERHEATERSAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two weeks

or more. Hydrogen gas can be explosive underthese circumstances.

If the hot water has not been used fin" two weeks or more, prevent the possibility of damage or iqjtu y by

turning on all hot water fimcets and allowing them to mn fin" severer minutes. Do this before using any

electrical appliance which is connected to the hot water sDtem. This simple procedure will allow any built-up

hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during

this process.

_ PROPERINSTALLATION

This washer must be properly installed and located in accordance with the Installation Instructions before it is used.

• Install o_"store x_he_'e it will not be exposed to • Pmpe_'ly gmtmd x_ashe_"to confi)rm with all

tempe_'attu'es below fl'eezing or exposed to the goxeming codes and o_'dinances, Follow details

x_eathe_, x_hich could cause pei'manent damage in Installation Instructions,

and imralidate the x_ammt)

YOURLAUNDRYAREA

• Keep the area underneath and around your

appliances ti'ee of combustible materials such as

lint, paper; rags and chemicals.

• Do not leave the washer door open. An open door

could entice children to hang on the door or

ci'awl inside the washe_:

• Close supervision is necessary if this appliance is

used b_ or near children. Do not allow children to

pla) on, with or inside this or any other appliance.

2

ge.com

WHENUSINgTIlEWASHER

• Never reach into washer while it is moving. • Never attempt to operate this appliance if

Wait until the machine has completely stopped it is damaged, malflmctioning, partially

before opening the door. disassembled, or has missing or broken parts,

Do not mix chlorine bleach with ammonia or including a damaged cord or )lu ,

acids such as vinegar and/or rust rell/over. • Do not slam the washer door closed. Do not t_y

Mixing dilti_rent chemicals can produce a toxic to torce the door open when locked (I,OCKED

gas which may cause death, indicator ON). This could result in damage to

the washer.

Do not wash or dry articles that have been

Use thb •

appliance

only for its

intended

purpose as

described in •

tbb Owner's

Manual

cleaned in, washed in, soaked in oi" spotted •

with combustible oi" explosive substances (such

as wax, oil, paint, gasoline, degreasers, (1i">

cleaning solvents, kerosene, etc.) which may

ignite or explode. Do not add these substances

to tile wash water. Do not use or place these

stlbstances ai'otlnd vo/11" washer or di'ver during

ol) era lion.

The laundry process can reduce the flame

retardancy of thbrics. To avoid such a result,

carefllllv follow the gam_ent lnanulhcturer's

wash and care instructions.

Tile washer is equipped with an electrical

overload protector. Tile motor will stop

if it becomes overheated. The washer will

automatically restart alter a cool-down

period of up to 2 hours, if tile washer

has not been manually turned off

during this time.

To minimize tile possibili U of electric shock,

unplug this appliance fl'om tile power supply

or disconnect the washer at the building's

distribution panel by removing tile fuse or

switching off the circuit breaker beflwe

attempting any maintenance oi" cleaning.

NOTE: Pressing tile power button does NOT

disconnect tile appliance from tile power

supply.

WHENNOTIN USE

• Turn off water fimcets to relieve pressure on

hoses and wflves and to minimize leakage if

a break or iupture should occur. Check tile

condition of the fill hoses; they should be

replaced every 5 years.

• Before discarding a washer, or removing it

f1"Oll/ service, reil/ove tile washer door to prevent

children ti'om hiding inside.

• Do not attempt to repair oi" replace any part of

this appliance tmless specifically recommended

in this Owner's Manual, or in published useI_

repair instiuctions that wm understand and

have the skills to carry out.

• Do not tamper with controls.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthe washer controlpanel

Youcan locate your model number on a label on the side of the washer.

Models WCVH6260 and WCVH6400

Models WHDVH626 and WHDVH660

Model WBVH6240

O Power

P_'ess to "wake up" the displa), If the display is a('ti_e, p_'ess to put the washe_" into stan(lb_ mode.

NOTE: Pressing POWER does not disconnect the appliance from the power suppl_

4

ge.com

Models GCVH6260and GCVH6600

Model WCVH6600

Models WBVH5100 and WBVH5200

O Power

P_'ess to "wake hi)" the displa). If the displa)' is a('ti_e, p_'ess to put the washe_" into stan(lb_ mode.

NOTE: Pressing POWER does not disconnect the appliance from the power suppl_

Aboutthe washer controlpanel

Youcan locate your model number on a label on the side of the washer.

Model GBVH5140

Models GHDVH626 and GHDVH670

O Power

Press to "wake up" the displa), If the display is a('ti_e, press to put the washer into stan(lb_ mode.

NOTE: Pressing POWER does not disconnect the appliance from the power suppl_

6

ge.com

Wash Cycles

The wash c_cles are optimized tar specific t)pes of wash loads. The chart below will help you match

the wash setting with the loads. The Gentle(:lean _'_lifters lightly tumble the clothes into the water

and detergent solution to clean the load.

WHITES Forheavilyto lightlysoiledwhite cottons,householdlinens,work andplayclothes.

COLORS/NORMAL Forheavyto lightlysoiledcolorfastcottons,householdlinens,work andplayclothes.

STAINWASH Forheavysoiledcolorfastcottons,householdlinens,workandplayclothes.

EASYCARE Forwrinkle-freeand permanentpressitems.

(PERMAPRESS)

ACTIVEWEAR Foractivesports,exerciseandsomecasualwearclothes.Fabricsincludemoderntechnologyfinishesand

fiberssuchasspandex,stretchandmicro-fibers.

DELICATES Forlingerieandspecial-carefabricswith light tonormalsoil. Providesgentletumblingandsoakduring

washandrinse.

HANDWASH Foritemslabeledhand-washablewith lightsoils. Providesgentlerockingto mimicthe handwashingaction.

WASHABLE Forthewashingof machinewashablewool products,providedthat theyarewashedaccordingto the

WOOLS instructionsonthe garmentlabel.Whenselectingthis cycle,youmustusea detergentsuitablefor

washingwool.

MY CYCLE Pressto use,createor modifycustomwash cycles.

SPEEDWASH Forlightlysoileditemsthat areneededin ahurry.Cycletime is approximately30minutes,depending

on selectedoptions.

DRAIN& SPIN Drainandspinat anytime.

RINSE& SPIN Toquicklyrinseout anyitems atanytime.

O

0

Soil Level

Changing the SOIl, I,EVEI, increases or decreases the wash time to remove (litterent amounts at soil.

To change the SOIl, I,EVEI,, press the SOIL LEVELbutton until you have reached the desired

setting, You can choose between Extra I,ight, I,ight, Normal or Heavv soil,

Spin Speed

Changing the SPIN SPEED changes the final spin speed at the cycles. Always tollow the tabric

inanuthcturer's care label when changing the SPIN SPEED.

To change the SPIN SPEED, press the SPIN SPEED button until wm have reached the desired

setting. Higher spin speeds are not awfilable on certain cycles, such as Delicates.

Higher spin speeds remove more water fl'om the clothes and will hel I) reduce dry time, but may

also increase the possibility of setting wrinkles on some tabrics.

Wash Temp

A(!just to select the proper water temi)erature tot the wash cycle. The prewash and rinse water is

always cold to hel I) reduce energy usage and reduce setting of stains and wrinkles.

Follow the tabric mantlthcturer's care label when selecting the wash telnl)erature.

To change the wash temperature, press the WASH TEMP button until you have reached the desired

setting. The Sanitized wash temperature is not awfilable on certain cycles, such as Delicates.

When selecting the Sanitize wash temperature, the washer increases the water temperature to

sanitize and kill more than 99% of many common bacteria found in home laundry. The sanitize

wash temperature is only available on Stain X4'ash and Whites Wash cycles. For best results, select

the heavv soil setting when using the Sanitize wash temperature setting.

NOTE: Thefkst 10seconds of the wash fill is always cold This feature assists in conditioning the fabric and

preventlbg stains from setting on garments.

START/PAUSE

Press to start a wash cycle. It the washer is running, pressing it once will pause the washer and

unlock the door. Press again to restart the wash cycle.

NOTE: If the washer is paused and the cycle is not restarted within 2hours, the current wash cycle will be cancelled

NOTE: Thewasher performs automatic system checks after pressing the STARTbutton. Water wi// flow

in 45 seconds or less. Youmay hear the door lock and unlock before water flows, this is normal 7

Aboutthe washerfeatures.

NOTE:Features may not be available on all washer models.

Cycle Signal

Use tile SIGNAL button to change tile

•,ohune of tile end of cycle signal.

Press the button until you reach the

desired _olmne.

Prewash (onsomemodels)

Prewash is an extra wash before tile

main wash. Use it tot heavilx soiled

clothes or for clothes with a care label

that recommends prewashing betore

washing. Be sm'e to add high-efficiency

detergent, or tile proper wash additive

to tile prewash dispense_:

NOTE: When selecting prewash, it is

recommended to use powder detergent in the

main wash (detergent) compartment.

0 EXTRA

RINSE

Extra Rinse

Llse an extra rinse when additional

finsin{* is desired to remoxe excess di_l

and detergent fl'om soiled loads.

Delay Start

Y}m can delay tile start oI a wash cycle t0r

u l) to 18 hours on models GHDVH626,

GCVH6260, X.VCVH6260, X._BVH6240,

WH DVH626, X.VCVH6600, X.VHDVH 660,

(;CVH6600 and (;HDVH670, and %r up

to 10 hems on models WBVH5100 and

GBVHS140. Press tile OELAYSTART

button to choose tile ntm]ber of hems

you want to delay tile strut of tile cycle,

then press the SYARTbutton. The

machine will count down and strut

automatically at the correct time,

NOTE"Ifyouforgettofullyclosethedoor,a

remindersignalwillbeepremindingyoutodosa

NOTE"Ifyouopenthedoorwhenthedelay

iscountingdown,themachinewillenterthe

pausestate.Youmustclosethedoorandpress

STARTagainin ordertorestartthecountdown.

Lock

You can lock tile controls to prevent any

selections fl'om being made. Or you can

lock tile controls after you have started a

cycle,

Children cannot accidentally start the washer

by touchingpadswith this optionselected

To lock tile washe_; press and hold tile

lock button tot 3 seconds. To tmlock the

washer controls, press and hold the lock

button fi)r .B seconds.

Tile control lock icon on tile display will

light up when it is on.

NOTE:ThePOWERbuttoncanstiff be used

whenthemachineislocked.

d)

8

HOLD 3 SEC

_os_o_E_

MY CYCLE(onsomemodels)

To save a _wofite cycle, set file d_ired

settings for wash cycle, soil le\'d, spin speed

and _;_sl/tern I) settings and hold down file

MgcgCtEbutt{m for 3 seconds. A beep will

sound to indicate file cvde has been saved,

To rise VO/lI" CtlStOill cycle press tile

MY CYCLEbutton before washing a load.

To change tile saxed cycle set tile

desired settings and hold down tile

MY CYCLEbutton fi)x 3 seconds.

NOTE:WhenusingMY CYCLEwash

optionscannotbemodifiedafter thecycle

hasbeenstarted

NOTE:If youchangewashoptionswith

MY CYCLEbeforestartingthecycle,the

MY CYCLEh_zhtwill turnoff andyouwill

bereturnedtothebasecycle.

FormodelsGHDVH626,GCVH6260,WCVH6260,WBVH6240,WHDVH626,WCVH6400,WCVH6600,WHDVH660,GCVH6600,GHDVH670 ge.com

The Dispenser Drawer

Slowl_ open the dispenser drawer by pulling it

()tit until it stops.

After addinglaundryproducts,slowlyclosethe

dispenserdrawer Closingthedrawertoo quickly

couldresultinearlydispensingof thebleach,

fabricsofteneror detergent.

Youmayseewaterin thebleachandfabricsoftener

compartmentsat theendof thecycle.Thisisaresult

of theflushing/siphoningactionand ispart of the

normaloperationof the washer

ThePrewash Compartment

Only use the Prewasb Compartment if you

are selecting tile Prewasb cycle ii_r heavily

soiled clothes. Add measured detergent/_r

prewash additive to the back left prewasb

corrlpartment of tile dispenser drinker.

• Detergent or prewash additive is flushed

fl'om the dispenser in the prewasb cycle

(if selected).

NOTE:Liquiddetergentwilldrainintothewasher

drumasit isadded.

Detergent usage rri{lt need to be a(!justed

flir water temperature, water hardness,

size and soil level of tile load. Avoid using

too much detergent in your washer as it

can lead to over sudsing and detergent

residue being left on the clothes.

insertinrearpositionforpowderdetergent

Liquid

insertinfor_/ardpositionforliquiddetergent

The Detergent Compartment

• High efficiency detergent is required

for this washer. Use the detergent

manufacturer's recommended amount.

The detergent selection insert must be placed

in the detergent corrlpartment in a specific

position according to what k_pe of detergent

you are using.

Powder Detergent- Place the insert in tile

,'ear position. The Powder Icons _ must

line up on center when the insert is in the

powder position.

LiquidDetergent- Place the insert in the

flw_ard position. The i,iquid Icons C_

must line up on center when the insert is

in the liquid position.

Move the insert b} pulling it up and replace

it b} sliding it down bet\_een either the ,'ear

or fl'ont detergent corripartment molded rails,

as desired, flir powder or liquid detergent.

• Add measured detergent to tile fl'ont left

detergent comparmlent of the dispenser

dr_:lwer.

Detergent is flushed J/'orri tile

dispenser at tile beginning of tile

wash cycle. Either powdered or liquid

detergent can be used.

Detergent usage rria} need to be ac!justed

tier water temperature, water hardness,

size and soil level of the load. A\oid using

too rrlucb detergent in your washer as it

ca,, lead to oversudsing" and detergent

residue being lett on the clothes.

TheLiquidBleach Compartment

If desired, measure out the recorrimended

arrio,lnt of liquid bleach, not to exceed

l/3 cup (80 ml) and pour into the center

compamnent labeled "IJ(_,)UID BLEACH"

marked with this symbol &.

Donotexceedthemaximumfill line.Overfillingcan

causeearly dispensingof thebleachwhichcouldresult

indamagedclothes.

NOTE:Donotusepowderedbleachin thedispenser

The Fabric Softener Compartment

If desired, pour the recommended ;:ii]lOiiIlt of

liquid ttd)ric softener into the compartment

labeled "E_BRIC SOFTENER."

Use only liquid fid)ric softener in the

dispenser.

Dilutewithwatertothemaximumfillline.

Donot exceedthemaximumfill line. Overfillingcan

causeearlydispensingof thefabricsoftenerwhich

couldstainclothes.

NOTE:Donotpourfabricsoftenerdirectlyon 9

thewashload.

Aboutthe washerfeatures.

FormodelsWBVH5100,WBVH5200and GBVH5140

ii ii i I

i(7/

The Dispenser Drawer

SloMy open tile dispenser drm,,er by pulling it

out until it stops.

Afteraddinglaundrypmflucaslowlyclosethe

dispenserdrawerClosingthedrawertooquickly

couldresultinearlydispensingof theblaach,

fabricsoftenerordetergent.

Youmayseewaterin thebleachandfabricsoftener

compartmentsattheendof thecycle.Thisisaresult

of theflushing/siphoningactionandispartof the

normaloperationofthewasher

Powda__

insertinrearpositionforpowderdetergent

Liquid /

insertinforwardpositienfor/iquiddetergent

The Detergent Compartment

• High effidency detergent is required

for this washer. Use the detergent

manufacturer's recommended amount.

Tile detergent selection insert must be placed

in the detergent compartment in a specific

position according to what t_pe of detergent

VOtl aye tlsiIlg.

PowderDetergent- Place the insert in tile

rear position. Tile Powder Icons _ must

line up on center when the insert is in the

powder position.

LiquidDetergent- Place tile insert in the

R)rward position. The iJquid Icons

must line up on center when the insert is

in the liquid position.

Move the insert b} pulling it up and replace

it bx sliding it down bet\_een either the rear

or fl'(mt detergent compartment molded rails,

as desired, for powder or liquid detergent.

• Add measured detergent to the Dont left

detergent compartment (if the dispenser

(trinket.

Detergent is flushed from tile

dispenser at tile beginning of tile

_Jsl/c)cle. Either powdered or liquid

detergent can be used.

Detergent usage may need to be a(!justed

tiir water temperature, water hardness,

size and soil level of the load. Axoid using

too much detergent in your washer as it

can lead to oxersudsing" and detergent

residue being left (m the clothes.

TheLiquidBleach Compartment

If desired, measure out the recommended

amount of liquid bleach, not to exceed

l/3 cup (80 ml) and pour into the

compartment lal)eled "I,I(5)UID BI,EACH"

marked with this s}mbol &.

Donotexceedthemaximumfill line.Overfillingcan

causeear/I/dispensing of thebleachwhichcouldresult

indamagedclothes.

NOTE:Donotusepowderedbleachin thedispenser

The Fabric Softener Compartment

If desired, pour the recommended amotmt of

liquid fitbric softener into the compartment

labeled "FABRIC SOFTENER."

Use only liquid tabric softener in the

dispenser.

Dilutewithwatertothemaximumfill line.

Donotexceedthemaximumfillline.Overfillingcan

causeearlydispensingof thefabricsoftenerwhich

couldstainclothes.

NOTE:Donotpourfabricsoftenerdirectlyon

thewash/oa_

10

Loadingand usingthe washer.

Always foflow fabric manufacturer's care label when laundering, ge.com

SortingWashLoads

Sort laundry into loads that can be washed together.

Colors Soil Fabric Lint

Whites Heavy Delicates Lint Producers

Lights Normal Easy Care Lint Collectors

Darks Light Sturdy Cottons

• Combinelargeandsmallitemsin a load LoadlargeitemsfirsLLargeitemsshouldnotbe morethanhalf the

total washload

• Washingsingleitemsis notrecommendedThismaycauseanout-of-balanceload.Add oneor two similar

items.

• Pillowsandcomfortersshouldnotbemixedwith otheritems.Thismaycausean out-of-balanceload

Loadingthe Washer

XM_sh d_mn may be fldlv loaded with loosely

added items. Do not wash fabrics containing

flammable materials (waxes, cleaning fluids, etc.).

To add items after washer has started,

press START/PAUSEand wait until the door is

unlatched. The washer may take up to 30 seconds

to unlock the door after I)ressing, START/PAUSE

depending on the machine conditions. Do not

try to force open the door when it is locked. After

the door unlocks, open gently: Add items, close

the door and press START/PAUSEto restart.

Careand Cleaning

Exterior: hmnediately wipe off any spills. Wipe with damp cloth. Do not hit surface with

sharp objects.

Interior: Dry around the washer door opening, flexible gasket (including attached hoses) and door

glass. These areas should always be clean to ensure a water tight seal.

It is recommended to rinse the washer at least once per year with 1/3 cup of bleach (no clothes),

using any of the wash cycles.

Moving and Storage: _sk the service technician to remove water fl'om drain pump and hoses.

Do not store the washer where it will be exposed to the weather. When moving the washei;

the tub should be kept stationary by using the shil)ping bolts removed during installation. See

Installation Instructions in this book. If these parts are not awfilable, thev can be ordered by

visiting our Website at ge.com or by calling 800.GE.CARES.

Long Vacations: Be sure water supply is sh tit off at faucets. Drain all water fl'om hoses if weather will

be below freezing.

11

Loadingand usingthe washer.

Always foflow fabric manufacturer's care label when laundering.

Dispenser Drawer Area: Detergent and fhbric softener may build u l) in the

dispenser drawer. Residue should be removed once or twice a re(ruth.

• Remove the drawer bv first pulling it out until it stops. Then reach back into

i the left rear corner of the drawer cavity and press down firmly on the lock

tab, pulling out tile drawer.

Lock tab is visible only after drawer

has been pulled out

Remove the inserts from the bleach and fhbric softener compartments and

tile detergent insert. Rinse tile inserts and tile drawer with hot water to

renlo;e traces of accunlulated laundr} products.

• To clean tile drawer opening, use a small bxush to clean tile recess. Remove

all residue froin tile upper and lower parts of tile recess.

• Return inserts to tile proper compartments. Replace tile dispenser drawer.

12

Aboutthe washer features, gecom

FabricCareLabels

Below are fi_bfi( (are label "svml)(_ls" that afle('t the cl(_thing you will be latlndei-]ng,

WASH LABELS

wash i i

cycle Normal p.......... t Press/ Gentled/ Do not wash Do not wrhlg

wrinkle resistant delicate Hand wash

Water • • • • • •

temperature Hot W .... Cold/cool

(50"C/120" F) (40"C/105' F) (30"C/85' F)

BLEACHLABELS

A A

SylIIuOIS Any bleach Only ....... hlorine bleach Do not bleach

(when needed) (when needed)

13

Installation

Instructions

Models

GBVH5140

GCVH6260

GCVH6600

GHDVH626

GHDVH670

WBVH5100

WBVH5200

WBVH6240

er

WCVH6260

WCVH6400

WCVH6600

WHDVH626

WHDVH660

I f you have any questions, call 800.GE.CARES(800.432.2737)orvisitourWebsiteat:ge.com

In Canada, call/.800.56L3344 orvisitgeappliances.ca

I

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - S_,,ethese

instructions fi)r local inspector's use.

• IMPORTANT - Obse,,'e_,ll

governing codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Consumer.

• Note to Consumer - KeeI) these insnuctions

fin" flmu'e reference.

• Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

• Completion time - 1-3 hours

• Proper installation is tile responsibility of tile

installer.

• Product failure due to improper installation is not

covered trader tile _*Varrantv.

FOR YOUR SAFETY:

WARNING

° This appliance must be I)r°I)erlx,,gr°unded and

installed as described in these Installation Instructions.

° Do not install or store appliance in an area where it

will be exposed to water/weather. See Locationof Your

Washor secfion.

• NOTE: This appliance must be properly grounded,

mid electrical service to the washer must conform with

local codes mid ordJnm_ces and the latest edition of

the National Electrical Code, ANSI/NFPA 70.

TOOLS REQUIRED FOR

WASHER INSTALLATION

1/4" nut driver

3/8" socket with ratchet

3/8" oi)en-end wrench

F_IA(!iustable wrench or 7/16" socket with ratchet

A(!justable wrench or 9/16" open-end wrench

(_hannel-lock a_!justable pliels

Caq)enter's level

PARTS SUPPLIED

Cable Tie

X,%_ter Hoses (2)

Hose (;uide

14

Installation Instructions

LOCATION OF YOUR WASHER

Do Not Install the Washer:

1. In an area exposed to dripping water or outside

weather conditions, The ambient temperature

should never be below 60°F (] 5.6°C) fl)r proper

washer operation,

2. In an area where it will come in contact with curtains

or drapes.

3. On caq_et. Tile floor MUST be a hard sm'iace with

a maximum slope of 1/2" per fi)ot (1.27 cm per

30 cm). To make sm'e tile washer does not vibrate

or IllOVe, yo/i Ill,Iv have to reinfl)rce tile floor.

NOTE: If floor is in poor condition, use 3/4"

impregnated plywood sheet solidly attached to existing

floor covering.

IMPORTANT:

Minimum Installation Clearances

* _._]/en installed in alcove: Sides, Rein;

Top : 0" (0 cm)

* _A]/en installed in closet: Sides, Rein;

T(,p 0" (0 cm), Front l" (2,54 cm)

* Closet door ventilation openings required:

2 louve_ each 60 square in, (387 cm_), located 3"

(7.6 cm) ti'om top and bottom of door

ROUGH-IN DIMENSIONS

FRONT

27.0"

(68.6cm)

20.4" (51.9cm)

ELECTRONICTRANSPARENTVISOR

40.6"_

(103.1cm)

SIDE

30.6"

177.7cm)

1.6"

(3.9cm)

_NOTE:With pedestal,52.6"

Stacked,84"

40.6"_

(lO&lcm)

39.1"

(09.2cm)

15

Installation Instructions

UNPACKING THE WASHER

WARNING: Rec,cle dest o,:the

and plastic bags after tile washer is unpacked. Make

materials inaccessible to children. Children might use

them fi)r play. Cations covered with rugs, bedspreads

or plastic sheets can become airtight chambe_

causing suffocation.

1. Grit and remove tile top and bottom packaging straps.

2. \._q/ile it is in tile carton, careflllly lay the washer on its

side. DO NOT lay tile washer on its ti'ont or back.

3. Tm'n down tile bom)m flaps--remove all base

packaging, including the cardboard, SQTOfi)am base

and stvrofi)am tub support (inserted in center of base).

NOTE: If you axe installing a pedestaJ, proceed to the

installation hastructio_s that come with the pedestal.

4. Carefldlv returi_ tile washer to an upright position and

i'elllOVe tile cai'[on,

5. Careflfllx move tile washer to within 4 teet (122 cm) of

tile final location.

6. Remove tile fi)llowing fl'om tile back side (ff tile washer:

4 bolts

4 plastic space_ (including rubber grommets)

4 power cord retaine_

NOTE: Failure to remove tile shipping braces can cause

the washer to become sexereE tmbalanced.

Save all bolts for future use.

NOTE: If you must transport tile washer at a later date,

you must reinstall tile shipping support hardware to

prevent shipping damage. Keep tile hardware in tile

plastic bag provided.

16

Installation Instructions

ELECTRICAL REQUIREMENTS

Read these instructions completely and carefully.

A WARNING--TO :DUCE

RISK OF" FIRE, ELECTRICAL SHOCK AND

PEILSONAL INJURY:

• DO NOT USE AN EXTENSION CORD ORAN

ADAPTER PLUG WITH THIS APPLIANCE.

Washer must be electrically grounded in accordance

with local codes and ordJnmlces, or in the absence

of local codes, in accordance with the NATIONAL

ELECTRICAL CODE, ANSI/NFPA NO. 70.

CIRCUIT - lndixidual, properly polarized and grounded

15-amp branch circuit fllsed with 15-amp time-delay fllse

or circuit breakei:

POWH/SUPPLY - 2-Mre, with ground, 120-xolt, single-

phase, 60-Hz, Mternating Current.

OUTLET RECEPTACLE -

Properly grounded

3-prong receptacle to be located

so the power supply cord is

accessible when the washer is

in an installed position.

GROUNDING REQUIREMENTS

A WARNING: hnproper connection of the

equipment grounding conductor can result in a risk

of electrical shock. Check with a licensed elecuician

if you are in doubt as to whether the appliance is

propedy grounded.

1, Tile washer MUST be grounded. In tile event ot

mMfimcfion or breakdown, grounding will 1educe

tile iisk (ff electiical shock by providing a path of least

resistance fi)r electrical current.

,

Since your washer is equipped with a p()wer supply

cord having an equipment-grounding conductor and

a grounding plug, tile plug MUST be plugged into an

appropriate, copper-wiied ieceptacle that is properly

installed and grounded in accordance with all local

codes and oiflinances oi" in tile absence ot local codes,

with the National Electrical Codes, ANSI/NFPA 70

(latest edition). It in doubt, call a licensed electiidan.

DO NOT cut off' or alter the grounding prong on the

power supply cord. In situations where a two-slot

receptacle is present, it is the owner's responsibility t()

have a licensed electrician replace it with a properly

grounded three-prong grounding-Qpe receptacle.

WATER SUPPLY REQUIREMENTS

Hot and cold water ti_ucets MUST be installed within

42 inches (107 cm) of your washer's water inlet. Tile

ti_ucets MUST be 3/4" (1.9 cm) garden hose-type so

inlet hoses can be connected. _,Vater pressure MUST be

between 10 and 120 pounds per square inch. Y()ur water

department can advise you of your water pressure.

Tile hot water mmperamre should be set to deliver

water at 120 ° to 140 °F (48°-60°C).

DRAIN REQUIREMENTS

1. Drain capable ot eliminating 17 gals (64.3 I.)

per minute.

2. A standpipe diameter of 1 1/4" (3.18 cm) minimum.

3. Tile standpipe height above tile floor

should be:

Minimum height: 24" (61 cm)

Maximum height: 96" (244 cm)

BACK -'," l

96 in.

I (244 cm)

I

i Max.

I

,,'4102m,

NOTE: Tile drain hose attached to tile washer can reach

a 58" (147 cm) high standpipe. For a higher standpipe,

contact an authorized parts distribut(n:

17

Installation Instructions

INSTALLING THE WASHER

1. Run some water fl'om the hot and cold flmcets to flush

the water lines and remove [)articles that might clog up

the water valve screens.

2. Remove the inlet hoses fl'om the plastic bag.

3. (90 ° elbow end)

Carefifllv connect the inlet

hose marked HOT to the

outside "H" outlet of the

water \;flve. Tighten by

hand, then tighten another

2/3 mrn with pliers.

Carefifllv connect the other

inlet hose to the inside "(7' (O

outlet of the water wflve.

Tighten by hand; then tighten another 2/3 turn with

pliers. Do not crossthread or over-tighten these

€onllections.

4. Connect the inlet hose ends to the HOT and COI,D

water fimcets tightly by hand, then tighten another 2/3

ttlFn with pliers. Turn the water on and check fin" leaks.

5°

6,

(_refldlv move the washer to its final location. Genflv

rock the washer into position. It is important not to

damage the rubber leveling legs when moving yore"

washer to its final location. Damaged legs can increase

washer vibration. It may be helI_fld to spray window

cleaner on the floor to hel I) move your washer into its

final position. NOTE: To reduce vibration, ensure that

all Ibm" rubber leveling legs are firefly touching the

floo_: Push and pull on the back right and then back

left of your washe_:

NOTE: Do not use the dispenser drawer or door to liti

the washer.

NOTE: If you are installing into a drain pan, you can

rise a 24-inch long 2x4 to lever the washer into place.

With the washer in its

final position, place a

level on top of the

washer (if the washer

is installed trader a

cotmter, the washer

should not be able to

rock). A_!just the fl'ont

leveling legs up or down to ensm'e the washer is

resting solid. Turn the lock nuts on each leg tlI)

towards the base of the washer and snug with a

wI'ench.

NOTE: Kee I) the leg extension at a minimum to

prevent excessive vibration. The ti_rther out the

legs are extended, the more the washer will vibrate.

If the floor is not level or is damaged, you may have

to extend the rear leveling legs.

18

Installation Instructions

INSTALLING THE WASHER (cont.)

7. Attach lJ-shaI)ed hose guide to tile end of tile drain

hose. Place tile hose in a laundry tub or standpipe

and secure it with the cable tie provided in the

enclosure package.

NOTE: If the drain hose is placed in a standpipe

without tbmfing a U shape, a siphoning action could

occm: There m ust be an air gap aro/md tile drain hose.

A snug hose fit can also cause a siphoning action.

CableTie/ CableTie._r

I

CableTie

8. Plug tile power cord into a grounded outlet.

NOTE: Check to be sure the power is off at a

circuit breaker/fuse box belm'e plugging tile power

coFd into an outlet.

9. Turn on tile power at a circuit breaker/fllse box.

10. Read the rest of this Owner's Manual. It contains

valuable and hell)tiff infi)rmation that will save vou

time and Illonev.

11. Before starting the washer, check to make sure:

Main power is turned on.

U_ITile washer is plugged in.

Tile water fimcets are turned on.

U_lThe refit is level and all fimr leveling legs are firefly

on tile floor.

U_ITile shil)ping suppo_l hardware is removed

and saved.

Tile drain hose is i)roperly tied up.

There are no leaks at tile timcet, drain line

or washen

12. Run tile washer through a complete cycle. Check

fi)r water leaks and proper operation.

1:3. If your washer does not operate, please review

the Before You Call For Service section belm'e

calling t(n" service.

14. Place these instructions in a location near the

washer fin" flmu'e reference.

REPLACEMENT PARTS

If replacement parts are needed fin" your washer; they

can be ordered in tile United States by visiting our

_,Vebsite at ge.com or by calling 800.GE.CARES.

19

Beforeyoucall forservice...

Troubleshooting tips

Save time and money! Review the charts on the following

pages first and you may not need to call for service.

Possible Cause What ToDo

Notspinningoragitating

Drain hose is kinked or

improperly commcted

" Straighten drain hose and make sure washer is not

sitting oil it.

Household drain may • Check household phunl_ing. You may need to call

he dogged a I)lumbe_:

Drain hose sipholmlg; drain hose • Ensure there is "an air .,_al) between hose and drain.

pushed too far down the draha

Washer pump Filter may • Have your l)ump filter cleaned.

be dogged

Load is out of balance • Redistribute dothes and run drain & spin (>1"rinse & sl)in.

" Increase load size if washing small load ((retaining hea\)'

and light items.

Leaking water Door gasket is damaged • Check to see if gasket is seated and not torn. Objects

left ill pockets may catlse damage to the washer (nails,

scre_vs, pens, pencils).

Door gasket not damaged • Water may drip fi'om the door when the door is opened.

This is a nom_al operation.

Check back left of washer • /f this area is wet, you have ove_udsing condition.

for water Use less detergent.

Fill hoses or drain hose is • Make sure hose connections are fight at washer and

improperly commcted timcets and make sure end ot drain hose is correctly

inserted in and secured to drain tiwilitv.

Household drain may • Check household plumbing. You may need to call

be dogged a phmd)e_:

Notdraining Drain hose is kinked or • Straighten drain hose and make St/l'e washer is not

improperly commcted sitting on it.

Household drain may • Check househ(>ld l)lund_ing. You may need to call

he dogged a l)lumbe_:

Drain hose sipholmag; drain hose • Ensure there is "an air .,_*al) between hose and drain.

pushed too far down the draha

Washer pump Filter may " Have your l)Ulnl ) filter cleaned.

be dogged

Notspinning Drain hose is kinked or " Straighten drain hose and make St/l'e washer is not

improperly commcted sitting on it.

Household drain may • Check househ(>ld l)lund_ing. You may need to call

he dogged a l)lumbe_:

Drain hose sipholmag; drain hose • Ensure there is "an air .,_*al) between hose and drain.

pushed too far down the draha

Washer pump Filter may " Have your l)Ulnl _filter cleaned.

be dogged

Load is out of balance " Re(fistfibute dothes and run drain & spin or rinse & spin.

• Increase h)ad size if washing small h)ad c_mtaining hea\y

and light items.

Motor is overheated • _\2Js]le_"motor will stop if it becomes overheated. [t will

atttomatica]]) restart after a coo] down period of up to

30 minutes (if washer has not been manually turned off).

Door is open • Make sure door is closed.

Page is loading ...

GE GCVH6800J5MR Owner's manual

GE GCVH6800J5MR Owner's manual

in other languages

Related papers

Other documents