MartinLogan Summit User manual

Brand: MartinLogan

Model: Summit

Category: Soundbar speakers

Type: User manual

S UMMIT

user’s manual

Serial Numbers: ________________ / ________________

Record your serial numbers here for easy reference. You will need this

information when filling out your warranty registration. Summit’s serial

number is located near the bottom of the backplate and on the shipping

container. Each individual unit has a unique serial number.

25Hz Setting: ________________ / ________________

left channel right channel

50Hz Setting: ________________ / ________________

left channel right channel

Thank you—to you the MartinLogan owner,

for loving what we do,

and

for making it possible for us to do what we love.

4 Contents

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation in Brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Controls and Connections . . . . . . . . . . . . . . . . . . . . . . . 7

AC Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Signal Connection

Break-In

Jumper Clips

Single-Wire Connection . . . . . . . . . . . . . . . . . . . . . . . . . 9

Bi-Wire Connection

Bi-Amplification

25Hz and 50Hz Level Control

Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Listening Position

The Wall Behind the Listener

The Wall Behind the Speakers

The Side Walls

Experimentation

Final Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

The Extra “Tweak”

Enjoy Yourself

Room Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Your Room

Terminology

Rules of Thumb

Dipolar Speakers and Your Room . . . . . . . . . . . . . . . . . 14

Solid Footing

The lightning bolt flash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient mag-

nitude to constitute a risk of electric shock.

Dispersion Interactions. . . . . . . . . . . . . . . . . . . . . . . . . 15

Controlled Horizontal Dispersion

Controlled Vertical Dispersion

Three Major Types of Dispersion

Home Theater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Electrostatic Advantages . . . . . . . . . . . . . . . . . . . . . . . . 17

Full Range Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MartinLogan Exclusives . . . . . . . . . . . . . . . . . . . . . . . . . 19

XStat™ Transducer

CLS™ (Curvilinear Line Source)

Generation 2 Diaphragm

MicroPerf Stator

Vacuum Bonding

AirFrame™ Technology

PoweredForce™ Woofers

Electrostatic Loudspeaker History . . . . . . . . . . . . . . . . 20

Frequently Asked Questions. . . . . . . . . . . . . . . . . . . . . 22

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Specifications

Warranty and Registration

Serial Number

Service

Glossary of Audio Terms . . . . . . . . . . . . . . . . . . . . . . . . 26

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

CONTENTS

WARNING! Do not use your Summit loudspeakers outside of the country of original sale—voltage requirements

vary by country. Improper voltage can cause damage that will be potentially expensive to repair. The Summit is

shipped to authorized MartinLogan distributors with the correct power supply for use in the country of intended

sale. A list of authorized distributors can be accessed at www.martinlogan.com or by emailing [email protected].

WARNING! The Summit features a down-firing woofer on the bottom of the cabinet. Setting the Summit flat on the

floor without the feet installed can damage this woofer. For this reason the Summit ships from the factory with the feet

installed. If, for some reason, you need to remove the Summit’s factory installed feet, carefully place the Summit on its

side until the feet are replaced. The down-firing woofer on the Summit requires at least 2 inches of clearance from the

floor for optimal performance. The Summit’s factory installed feet are specifically engineered to meet this requirement.

Installation in Brief 5

We know you are eager to hear your Summit speakers, so

this section is provided to allow fast and easy set up. Once

you have them operational, please take the time to read,

in depth, the rest of the information in this manual. It will

give you perspective on how to attain the greatest possible

performance from this most exacting transducer.

If you should experience any difficulties in the setup or

operation of your Summit speakers, please refer to the Room

Acoustics, Placement or Operation sections of this manual.

Should you encounter a persistent problem that cannot

be resolved, please contact your authorized MartinLogan

dealer. They will provide you with the appropriate technical

analysis to alleviate the situation.

WARNING!

• Hazardous voltages exist inside—do not

remove cover.

• Refer servicing to a qualified technician.

• To prevent fire or shock hazard, do not

expose this module to moisture.

• Turn amplifier off and unplug speaker should

any abnormal conditions occur.

• Turn amplifier off before making or breaking

any signal connections!

• Do not operate if there is any visual damage

to the electrostatic panel element.

• Do not drive speaker beyond its rated power.

• The power cord should not be installed,

removed, or left detached from the speaker

while the other end is connected to an AC

power source.

• Use only with a grounded electrical outlet.

• No candles or other sources of open flame

should be placed on the speaker.

• No liquids either in glasses or vases should be

placed on speaker.

• Speaker should not be exposed to dripping or

splashing liquids.

• The terminals marked with the lightning bolt

symbol should be connected by an instructed

person or by way of ready made terminals.

Step 1: Unpacking

Remove your new Summit speakers from their packaging.

Step 2: Placement

Place each Summit at least two feet from the back wall and

angle them slightly toward your listening area. This is a good

place to start. Please see the Placement section (pages 11–

12) of this manual for more details.

Step 3: Power Connection (AC) (see warning)

Your Summit speakers require AC power to energize their

electrostatic cells and to power the PoweredForce™ woofers.

Using the AC power cords provided,

plug them in

first to

the AC power receptacle on the rear panel of the speaker

making sure that you have made a firm

connection, and

then to a wall outlet. Please see AC Power Connection

(pages 8) of this manual for more details.

Step 4: Signal Connection

Use the best speaker cables you can. Higher quality cables,

available from your specialty dealer, are recommended

and will give you superior performance. Spade connectors

are suggested for optimum contact and ease of installation.

Attach your speaker cables to the signal input section on the

rear panel. Be consistent when connecting speaker leads to

the terminals on the back of the Summit. Take great care to

assign the same color to the (+) terminal on both the left and

right channels. If bass is nonexistent and you cannot discern

a tight, coherent image, you may need to reverse the (+) and

(–) leads on one side to bring the system into proper polarity.

For detailed setup instructions, please turn to the Controls

and Connections section (Page 7–10) of this manual for

more details.

Step 5: Control Settings

Set the 25Hz and 50Hz Bass Level Control knobs to 0dB.

Please see 25Hz and 50Hz Level Control (page 9) of this

manual for more details.

Step 6: Listen and Enjoy

Now, you may turn on your system and enjoy!

INSTALLATION IN BRIEF

6 Introduction

Congratulations! You have invested in one of the world’s

premier loudspeaker systems.

The MartinLogan Summit represents an advanced

combination of sonic technologies establishing an unprec-

edented direction for audiophile design. The result of

years of research, the new Summit™ hybrid electro-

static loudspeaker features PoweredForce™ and XStat™

technologies, dramatically reducing cabinet size, yet

establishing new standards for efficiency, dynamics and

precision in a floorstanding loudspeaker.

The luminous legacy of MartinLogan subwoofer engi-

neering and research not only produced some of the

world’s most sophisticated subwoofers, but has also

yielded new breakthroughs. Through integrated engineer-

ing of advanced amplification and transducer designs,

PoweredForce™ bass technology results in usable bass

extension down to 24Hz, immense bass dynamics and

precision beyond the reach of traditional passive box sys-

tems—all from an enclosure not much larger than a case of

wine! Additionally, low-frequency equalization capabili-

ties, integrated into advanced PoweredForce™ technology,

allow precision calibration for optimal room integration.

Housed within a radical, ultra-rigid, billet and extruded

aluminum AirFrame™, the Summit’s™ new CLS XStat™

transducer builds upon the legacy of MartinLogan’s elec-

trostatic heritage with the incorporation of advanced

vacuum bonding and MicroPerf stat panels, providing

even greater efficiency and precision. The integration of

exotic toroidal transformer engineering and an electri-

cal interface technology developed by MartinLogan’s

Statement™ e2x engineering team extends effortless

dynamics and purity, resulting in even higher sonic stan-

dards of efficiency and precision.

Featuring an advanced crossover topology derived from

the Statement™ loudspeaker, MartinLogan carefully

hand-builds each Summit™ crossover utilizing precision

point-to-point wiring, audiophile-grade polypropylene

capacitors and high-purity air-core coils. This advanced

crossover topology flawlessly preserves microscopic sub-

tleties while effortlessly handling the broadest range of

dynamics contained within even the most demanding

sonic source.

The materials in your new Summit speakers are of the high-

est

quality and will provide years of enduring enjoyment

and

deepening respect. The cabinetry is constructed

from the highest quality composite material for acoustical

integrity and features hand rubbed wood veneers.

Through rigorous testing, the curvilinear electrostatic

panel has proven itself to be one of the most durable and

reliable transducers available today. Fabricated from a

custom tool punched high-grade steel, the patented

panel is then coated with a special polymer that is applied

via a proprietary electrostatic bonding process. This panel

assembly houses a membrane just 0.0005 of an inch thick.

Ruggedly constructed and insulated, the panel is rated to

easily handle up to 300 watts of continuous power with

no deleterious effects.

The other sections of your User’s Manual explain in detail

the operation of your Summit speakers and the philoso-

phy applied to their design. A clear understanding of your

speakers will insure that you obtain maximum performance

and pleasure from this most exacting transducer. It has been

designed and constructed to give you years of trouble-free

listening enjoyment.

INTRODUCTION

Light Knob

The light control knob allows

the brightness of the illuminat-

ed strip to be adjusted.

25Hz Level Knob

The 25Hz Level knob sig-

nificantly adjusts the level

between 20 and 30Hz by

±10dB. This is an area where

peaks and dips of different

amplitudes often manifest in

real environments. This set-

ting is dependent on room

size and construction, system

configuration and personal

preference.

ESL Signal Input

This set of binding posts pro-

vides a place to connect the

signal that drives the XStat™

ESL transducer.

Woofer Signal Input

This set of binding posts pro-

vides a place to connect

the signal that drives the

PoweredForce™ woofers.

AC Power Connection

Because your MartinLogan

Summit speakers use an inter-

nal power supply to energize

their electrostatic cells, they

must be connected to an AC

power source.

Controls and Connections 7

CONTROLS AND CONNECTIONS

50Hz Level Knob

The 50Hz Level knob sig-

nificantly adjusts the level

between 40 and 60Hz by

±10dB. This is an area where

peaks and dips of different

amplitudes often manifest in

real environments. This set-

ting is dependent on room

size and construction, system

configuration and personal

preference.

Status Light

The Summit is equipped with a

multi-color LED to indicate the

current status of the woofers.

The following list explains the

meaning of the different colors:

No color: No power. The

Summit is not plugged in.

Green: Play mode. This indi-

cates the Summit detects an

audio signal and has auto-

matically switched into play

mode.

Yellow: Standby mode. This

indicates the Summit has

detected no audio signal for

approximately 5 minutes and

has automatically switched

into standby mode.

Red: Initializing or Safe mode.

This indicates that the Summit

is initializing. This also indicates

if the Summit’s temperature has

exceeded nominal operating

range. If the Summit overheats,

please allow the Summit to

cool and reset it by unplugging

the unit and plugging it back in.

Figure 1. Summit Controls and Connections

AC Power Connection

8 Controls and Connection

Because your Summit speakers use an internal power

supply to energize their electrostatic cells and to power

the PoweredForce™ woofers, they must be connected to

an AC power source. For this reason they are provided

with the proper IEC standard power cords. These cords

should be firmly inserted into the AC power receptacles

on the rear connection panel of the speakers, then to any

convenient AC wall outlet. The Summit’s integrate a signal

sensing power supply which will switch off after five min-

utes of no music signal, and requires less than two seconds

to recharge the panels when a music signal is present.

Your Summit speakers are wired for the power service

supplied in the country of original consumer sale.

The AC power rating applicable to a particular unit

is specified both on the packing carton and on the

serial number plate attached to the speaker. If you

remove your Summit speakers from the country

of original sale, be certain that the AC power supplied

in any subsequent location is suitable before connect-

ing and operating the speakers. Substantially impaired

performance or severe damage may occur to an Summit

speaker if operation is attempted from an incorrect AC

power source.

WARNING! The power cord should not be

installed, removed, or left detached from the

speaker while the other end is connected to an

AC power source.

Signal Connection

Use the best speaker cables you can. The length and type

of speaker cable used in your system will have an audible

effect. Under no circumstance should a wire of gauge

higher (thinner) than #16 be used. In general, the lon-

ger the length used, the greater the necessity of a lower

gauge, and the lower the gauge, the better the sound,

with diminishing returns setting in around #8 to #12.

A variety of cables are available whose

manufacturers

claim better performance than standard heavy gauge wire.

We have verified this in many cases, and the improvements

available are often more noticeable than the differences

between wires of different gauge. The effects of cables

may be masked if equipment is not of the highest quality.

Connections are done at the signal input section on the

rear electronics panel of the Summit. Use spade connec-

tors for optimum contact and ease of installation. Hand

tighten the binding posts, but do not overtighten—do not

use a tool to tighten the binding posts.

Be consistent when connecting the speaker cables to the

signal input terminals. Take care to assign the same color

cable lead to the (+) terminal on both the left and right

channel speakers. If bass is nonexistent and you cannot

discern a tight, coherent image, you may need to reverse

the (+) and (–) leads on one speaker to bring the system

into proper polarity.

WARNING! Turn your amplifier off before

making or breaking any signal connections!

Break-In

When you first begin to play your Summit speakers, they

will sound a bit bass shy. This is due to the high quality,

long-life components used in our woofer. Our custom

made, butyl surround woofer requires approximately

72 hours of break-in at 90 dB (moderate listening levels)

before any critical listening. The break-in requirements

of the crossover components (and, to a lesser degree, the

stator) are equivalent.

Jumper Clips

In some countries federal law prohibits MartinLogan from

supplying jumper clips. If none are found installed under

your speakers binding posts, please refer to ‘Bi-Wire

Connection’ for connection instructions.

Single Wire Connection

Controls and Connection 9

Please take note of the jumper clips installed under the

binding posts. These clips attach the high and low fre-

quency sections of the crossover together. Leaving these

in place, connect the (+) wire from your amplifier to

either red binding post and the (–) wire from your ampli-

fier to either black binding post (see figure 2).

Bi-Wire Connection

Bi-wiring the Summit is not necessary. The Summit is pro-

vided with a bi-wiring option to allow consumers who

already own quality bi-wire cables to use their existing

cables. This connection method replaces the jumper clips

installed

under the binding posts with individual runs of

speaker wire from your amplifier. This doubles the signal

carrying conductors from the amplifier to the speaker, thus

direct-coupling each portion of the crossover to the amplifier.

First you must remove the jumper clips. Connect one set

of wires to the upper set of ESL binding posts. Next, con-

nect a second set of wires to the lower woofer binding

posts. Finally, connect both sets of wires to the appro-

priate terminals on your amplifier. Please take care to

connect both (+) wires to the (+) amplifier terminals and

both (–) wires to the (–) amplifier terminals. This is also

known as a parallel connection (see figure 3).

The Summit’s PoweredForce™ woofers are internally

powered. Because of this, we do not recommend either

active or passive bi-amplification.

25Hz and 50Hz Level Control

After you have determined the speaker position and pri-

mary listening position (see pages 11–12) you will want to

adjust the 25Hz and 50Hz level controls

On the rear of the Summit are two knobs that control

the 25Hz and 50Hz frequency responses by ±10db.

MartinLogan engineers have found this frequency area

(20–75Hz) to be problematic. Low frequencies tend to

react to a room environment by creating nodes (boomy

and unnatural bass) or nulls (nonexistent bass). By adjust-

ing the 25Hz and 50Hz level knobs you can ‘dial out’

undesirable nodes or nulls and create a balanced and

seamless presentation.

To help find the optimal setting for your room, play mate-

rial with (which you are familiar) with low frequency

information (such as a drum or a pipe organ). When

adjusting the 25Hz and 50Hz levels we recommend doing

so with two or three people—one located at the listening

position and one or two people at the controls.

Figure 2. Single-wire connection. One channel shown. Figure 3. Bi-wire connection. One channel shown.

Bi-Amplification

10 Controls and Connection

1 Start with the 25Hz and 50Hz level knobs set to 0dB.

The person at the listening position needs to become

familiar with the sound at this setting. Remember, only

the person in the listening position should judge the

bass integration. Nodes and nulls change dramatically

throughout every location in a room. A person adjust-

ing the controls on the speaker will experience an

entirely different bass performance than a person sit-

ting in the listening position.

2 Adjust the 25Hz level knob by +10dB. In most cases

the bass will sound boomy and unnatural. Return

the setting to 0dB and listen to the speaker again for

a moment. Next, adjust the 25Hz knob by –10dB.

In most cases the bass will sound thin and nonexis-

tent. Return the setting to 0dB and listen again for a

moment.

Now you have an idea of the control you have over

the 25Hz output. If you feel the bass is too boomy

at 0dB, adjust towards the negative settings. If it is

to thin at 0dB, adjust toward the positive settings.

Repeat this procedure using increasingly smaller

amounts (8dB, 6dB, 4dB, etc.) until you find a setting

where the low bass sounds balanced—remember

to return the knob to 0dB and listen for a moment

between each adjustment. Once you’ve found the best

sounding setting for your room, make a note of the setting.

3 Repeat step 2 to adjust the 50Hz level knob

4 Setting one level may effect enough change that the

other is no longer ideal. Once you have determined

and noted the settings for both knobs repeat this pro-

cedure with finer adjustments around the points you’ve

already chosen.

Remember—due to the unpredictabililty of every listening

room experimentation is essential when setting up

a loudspeaker. It may take several attempts to find a

combination of control settings, speaker positions, and

listening position that is ideal for you and your listening

preferences. If you still hear anomalies, you may need to

experiment with speaker placement or the location of the

listening position—sometimes even the subtlest adjust-

ments will make huge changes!

By now your speakers should be placed approximately

two to three feet from the front wall, the wall in front of the

listening position, and about two feet from the side walls.

Your sitting distance should be further than the distance

between the speakers themselves. You are trying to attain

the impression of good center imaging and stage width.

There is no exact distance between speakers and listener,

but there is a relationship. In long rooms, naturally, that

relationship changes. The distance between the speakers

will be far less than the distance from you to the speaker

system. However, in a wide room, you will still find that

if the distance from the listener to the speakers becomes

smaller than the distance between the speakers themselves,

the image will no longer focus in the center.

Now that you have positioned your speaker system, spend

time listening. Wait to make any major changes in

your initial

setup for the next few days as the speaker

system itself will

change subtly in its sound. Over the first 72 hours of play the

actual tonal quality will change slightly with deeper bass and

more spacious highs resulting. After a few days of listening

you can begin to make refinements and hear the differences.

The Wall Behind the Listener

Near-field reflections can also occur from your back wall (the

wall behind the listening position). If your listening position

is close to the back wall, these reflections can cause prob-

lems and confuse imaging quality. It is better for the wall

behind you to be absorptive than to be reflective. If you

have a hard back wall and your listening position is close to

it, experiment with devices that will absorb information

(i.e. wall hangings and possibly even sound absorbing panels).

The Wall Behind the Speakers

The front surface, the wall behind the speakers, should

not be extremely hard or soft. A pane of glass will cause

reflections, brightness and confused imaging. Curtains,

drapery and objects such as bookshelves can be placed

along the wall to diffuse an overly reflective surface. A

standard sheet rock or textured wall is generally an ade-

quate surface if the rest of the room is not too bright and

hard. Walls can also be too soft. If the entire front wall

consists of heavy drapery, your system can sound dull.

You may hear muted music with little ambience. Harder

surfaces will actually help in this case.

The front surface ideally should be one long wall without

any doors or openings. If you have openings, the reflection

and bass characteristics from each channel can be different.

The Side Walls

A good rule of thumb is to have the side walls as far away

from the speaker sides as possible. However, MartinLogan’s

unique controlled dispersion electrostatic transducer

inherently minimizes side wall reflections—a position as

little as two feet from the side walls often proves adequate.

Sometimes, if the system is bright or the imaging is not to

your liking, and the side walls are very near, try putting

curtains or softening material directly to the edge of each

speaker. An ideal side wall, however, is no side wall at all.

Experimentation

Toe-in—Now you can begin to experiment. First begin

by toeing your speakers in towards the listening area and

then facing them straight into the room. You will notice

the tonal balance and imaging changing. You will notice

that as the speakers are toed-out, the system becomes

slightly brighter than when toed-in. This design gives you

the flexibility to compensate for a soft or bright room.

Generally it is found that the ideal listening position is with

the speakers slightly toed-in so that you are listening to the

inner third of the curved transducer section. A simple, yet

effective method to achieve proper toe involves sitting at the

listening position, holding a flashlight under your chin and

pointing it at each speaker. The reflection of the flashlight

should be within the inner third of the panel (see figure 4).

PLACEMENT

Listening Position

Placement 11

Figure 4. Flashlight toe-in technique.

12 Placement

Tilting the Speakers Backwards and Forwards—As the

diagrams show in the Dispersion Interactions section of

this manual (page 15), the vertical dispersion is directional

above and below the stator panel itself. In some instances,

if you are sitting close to the floor, slight forward tilting of

the speakers can enhance clarity and precision.

Imaging—In their final location, your Summit’s can have a

stage width somewhat wider than the speakers themselves.

On well recorded music, the instruments can extend

beyond the edges of each speaker (left and right), yet

a vocalist should appear directly in the middle. The size of the

instruments should be neither too large nor too small, subject

to the intent and results of each unique audio recording.

Additionally, you should find good clues as to stage

depth. Make sure that the vertical alignment, distance from

the front wall, and toe-in is exactly the same for both speakers.

This will greatly enhance the quality of your imaging.

Bass Response—Your bass response should neither be

one note nor should it be too heavy. It should extend to the

deepest organ passages and yet be tight and well defined.

Kick-drums should be tight and percussive—string bass

notes should be uniform and consistent throughout

the entirety of the run without booming or thudding.

Tonal Balance—Voices should be natural and full and

cymbals should be detailed and articulate yet not bright and

piercing, pianos should have a nice transient characteristic

and deep tonal registers. If you cannot attain these virtues,

read the section on Room Acoustics (pages 13–14). This

will give you clues on how to get closer to these ideal virtues.

Final Placement

After the full break in period, obtaining good wall treat-

ments, and the proper toe-in angle, begin to experiment

with the distance from the wall behind the speakers.

Move your speaker slightly forward into the room. What

happened to the bass response? What happened to the

imaging? If the imaging is more open and spacious and

the bass response is tightened, that is a superior position.

Move the speakers back six inches from the initial setup

position and again listen to the imaging and bass response.

There will be a position where you will have pinpoint

imaging and good bass response. That position is the point

of the optimal placement from the front wall.

Now experiment with placing the speakers farther apart.

As the speakers are positioned farther apart, listen again,

not so much for bass response but for stage width and

good pinpoint focusing. Your ideal listening position

and speaker position will be determined by:

• Tightness and extension of bass response

• Width of the stage

• Pinpoint focusing of imaging

Once you have determined the best of all three of these

considerations, you will have your best speaker location.

The Extra “Tweak”

This extra “tweak” may be useful when your speakers

are placed in a dedicated listening room. Use the fol-

lowing procedure and measurements for your speakers

placement to see what can happen to your system’s per-

formance. These formulas will help determine optimum

placement of your speakers to minimize standing waves.

1 Distance from the front wall (in front of the listening

position) to the center of the curvilinear transducer: To

determine distance from the front wall, measure the

ceiling height (inches) and multiply the figure by 0.618

(i.e. ceiling height (inches) x 0.618 = the distance from

the front wall to the center of the curvilinear transducer).

2 Distance from the side-walls to the center of the cur-

vilinear transducer: To determine distance from the

side walls, measure the width of your room in inches

and divide by 18. Next, multiply the quotient by 5 (i.e.

room width in inches / 18 x 5 = the distance from the

side-walls to the center of the curvilinear transducer).

Enjoy Yourself

The Summit is a very refined speaker and benefits from

care in setup. With these tips in mind you will find, over

your months of listening, that small changes can result

in measurable differences. As you live with your speak-

ers, do not be afraid to experiment with their positioning

until you find the optimal relationship between your room

and speaker system that gives to you the best results. Your

efforts will be rewarded.

This is one of those areas that requires both a little back-

ground to understand and some time and experimentation

to obtain the best performance from your system.

Your room is actually a component and an important part

of your system. This component is a very large variable

and can dramatically add to, or subtract from, a great

musical experience.

All sound is composed of waves. Each note has its own

wave size, with the lower bass notes literally encompassing

from 10’ feet to as much as 40’ feet. Your room partici-

pates in this wave experience like a three dimensional pool

with waves reflecting and becoming enhanced depending

on the size of the room and the types of surfaces in the room.

Remember, your audio system can literally generate all of

the information required to recreate a musical event in

time, space, and tonal balance. Ideally, your room should

not contribute to that information. However, every room

does contribute to the sound to some degree. Fortunately

MartinLogan had designed the Summit to minimize these

anomalies

Let’s talk about a few important terms before we begin.

Terminology

Standing Waves

The parallel walls in your room will reinforce certain notes

to the point that they will sound louder than the rest of

the audio spectrum and cause “one note bass”, “boomy

bass” or “bloated bass”. For instance, 100Hz represents a

10 feet wavelength. Your room will reinforce that specific

frequency if one of the dominant dimensions is 10 feet.

Large objects in the room such as cabinetry or furniture

can help to minimize this potential problem. Some seri-

ous “audiophiles” will literally build a special room with

no parallel walls just to help eliminate this phenomenon.

Reflective Surfaces (near-field reflections)

The hard surfaces of your room, particularly if close to your

speaker system, will reflect some waves back into the room

over and over again, confusing the clarity and imaging of

your system. The smaller sound waves are mostly affected

here, and occur in the mid and high frequencies. This is

where voice and frequencies as high as the cymbals occur.

Resonant Surfaces and Objects

All of the surfaces and objects in your room are subject to

the frequencies generated by your system. Much like an

instrument, they will vibrate and “carry on” in syncopation

with the music, and contribute in a negative way to the

music. Ringing, boominess, and even brightness can occur

simply because they are “singing along” with your music.

Resonant Cavities

Small alcoves or closet type areas in your room can be

chambers that create their own “standing waves” and can

drum their own “one note” sounds.

Clap your hands. Can you hear an instant echo respond

back? You have near-field reflections. Stomp your foot

on the floor. Can you hear a “boom”? You have standing

waves or large panel resonances such as a poorly sup-

ported wall. Put your head in a small cavity area and talk

loudly. Can you hear a booming? You’ve just experienced

a cavity resonance.

Rules of Thumb

Hard vs. Soft Surfaces

If the front or back wall of your listening room is soft, it

might benefit you to have a hard or reflective wall in

opposition. The ceiling and floor should follow the same

basic guideline as well. However, the side walls should be

roughly the same in order to deliver a focused image.

This rule suggests that a little reflection is good. As a matter

of fact, some rooms can be so “over damped” with carpet-

ing, drapes and sound absorbers that the music system

can sound dull and lifeless. On the other hand, rooms can

be so hard that the system can sound like a gymnasium

with too much reflection and brightness. The point is that

balance is the optimum environment.

Breakup Objects

Objects with complex shapes, such as bookshelves, cabinetry

and multiple shaped walls can help break up those sonic

gremlins and diffuse any dominant frequencies.

Solid Coupling

Your loudspeaker system generates frequency vibrations or

waves into the room. This is how it creates sound. These

vibrations vary from 20 per second to 20,000 per sec-

Your Room

Room Acoustics 13

ROOM ACOUSTICS

ond. If your speaker system is not securely planted on the

floor or solid surface, it can shake as it produces sound

and, consequently, the sound can be compromised. If

your speaker is sitting on the carpet and only foot gliders

are used, the bass can be ill defined and even boomy. The

use of spikes is recommended to insure secured footing for

your speakers. (See ‘Solid Footing’ for spike information

and installation instructions).

Dipolar Speakers and Your Room

MartinLogan electrostatic loudspeakers are known as dipo-

lar radiators. This means that they produce sound from

both their fronts and their backs. Consequently, musical

information is reflected by the wall behind them and may

arrive, either in or out of step, with the information pro-

duced by the front of the speaker.

The low frequencies can either be enhanced or nulled by

the position from the front wall. Your Summit’s have been

designed to be placed two to three feet from the front

wall (the wall in front of the listening position) to obtain

the best results; however, your room may see things dif-

ferently. So listening to the difference of the bass response

as a result of the changes in distance from the front wall

can allow you to get the best combination of depth of bass

and tonal balance.

Now that you know about reflective surfaces and reso-

nant objects, you can see how the midrange and high

frequencies can be affected. The timing of the initial wave

as it radiates to your ears, and then the reflected informa-

tion as it arrives at your ears later in time, can result in

confusion of the precious timing information that carries

the clues to imaging. Consequently the result is blurred

imaging and excessive brightness. Soft walls, curtains, wall

hangings, or sound dampeners (your dealer can give you

good information here) can be effective if these negative

conditions occur.

Solid Footing

After living and experimenting with your Summit’s, you

may want to use ETC (energy transfer coupler) spikes sup-

plied with the Summit (see figure 5). With the use of these

spikes, the Summit will become more firmly planted on

the floor and, consequently, bass will tighten and imag-

ing will become more coherent and detailed. It is best not

to implement the spikes, however, until you are secure in

the positioning, as the spikes can damage the floor if the

speaker is moved. The feet that attach to the bottom of

the Summit use a common

/8“ x 16 thread. The threaded

spike insert itself is a

/4“ x 16 thread.

Spike Installation Instructions:

1 Carefully lay your speaker on its side to gain access to

the bottom. (See the warning on back cover.)

2 Remove the jam nut from the bottom of the foot.

3 Remove the threaded spike insert. Flip the threaded

spike insert 180 degrees to expose the spike. Replace

the threaded spike insert.

4 Re-install the jam nut.

5 Right the speaker. Caution: Make sure your hands and

any cabling are clear of the spikes. Do not slide speaker as

spikes are sharp and can damage your floor or carpet.

6 Adjust to level by the rotating spikes. Tighten the jam nut

securely when satisfied that speaker is level. Caution:

walking the speaker may result in a broken spike or foot.

Figure 5. The ETC™ Spike.

14 Placement

Your Summit’s launch a 30 degree horizontal dispersion

pattern. This horizontal dispersion field gives a choice of

good seats for the performance while minimizing inter-

actions with side walls (see figure 10). Make sure both

speakers stand exactly at the same vertical angle, otherwise

the image can be skewed or poorly defined. The wave

launch of both speakers is extremely accurate in both the

time and spectral domain. Consequently, small refined

adjustments can result in noticeable sonic improvements.

Controlled Vertical Dispersion

As you can see from the illustrations, your Summit speak-

ers project a controlled dispersion pattern (see figure 11).

Each Summit is a 44 inch line source beginning 15 inches

above the base. This vertical dispersion profile minimizes

interactions with the floor and the ceiling.

It is a known fact that as the sound wave becomes pro-

gressively smaller than the transducer producing it,

the dispersion of that wave becomes more and more

narrow, or directional. This fact occurs as long as the

transducer is a flat surface. Large flat panel speakers

exhibit venetian blind effects due to this phenomenon.

This is one reason why many manufacturers opt for small

drivers (i.e. tweeters and midrange) to approximate

what is known as a point source wave launch.

Historically, most attempts to achieve smooth dispersion

from large flat panel transducers resulted in trade-offs.

After exhaustive testing of many different methods, we

conceived an elegantly simple, yet intensely hand craft-

ed process. By curving the radiating surface, we create

the effect of a horizontal arc. This allows the engineers at

MartinLogan to control the high frequency dispersion pat-

tern of our transducers.

Three Major Types of Dispersion

Figure 6–7. As can be seen here, point source

concepts invite a great deal of room interaction.

While delivering good frequency response to a

large listening audience, imaging is consequently

confused and blurred.

Figure 8–9. Even though they suffer from

“venetian blind” effect, angled multiple panel

speakers can deliver good imaging, but only

to specific spots in the listening area.

Figure 10–11. A controlled 30 degree cylindri-

cal wave-front, a MartinLogan exclusive, offers

optimal sound distribution with minimal room

interaction. The result is solid imaging with a

wide listening area.

Controlled Horizontal Dispersion

Dispersion Interactions 15

DISPERSION INTERACTIONS

16 Home Theater

It had long been the practice of stereo buffs to connect their

television to a stereo system. The advantage was the use of

the larger speakers and more powerful amplifier of the

stereo system. Even though the sound was greatly improved,

it was still mono and limited by the broadcast signal.

In the late 1970’s and early 1980’s two new home movie

formats became widely available to the public: VCR and

laser disc.

By 1985, both formats had developed into very high quality

audio/video sources. In fact, the sonic performance of some

video formats exceeded audio-only formats. Now, with

theater-quality sound available at home, the only element

missing was the "surround sound" presentation found in

movie houses.

Fortunately, Dolby and DTS encoded movies (including

almost all films) have the same surround sound informa-

tion encoded on home releases as the theatrical release.

All that is required to retrieve this information is a decoder

and additional speakers and amps to reproduce it.

Home theater is a complex purchase and we recommend

that you consult your local MartinLogan dealer, as they

are well versed in this subject.

Each piece of a surround system can be purchased sepa-

rately. Take your time and buy quality. No one has ever

complained that the movie was too real. The following list

and descriptions will give you only a brief outline of the

responsibilities and demands placed on each speaker.

Front Left and Front Right

If these speakers will be the same two used for your stereo

playback, they should be of very high quality and able to

play loudly (over 102 dB) and reproduce bass below 80 Hz.

Center Channel

This is the most important speaker in a home theater

system, as almost all of the dialogue and a large portion of

the front speaker information is reproduced by the cen-

ter channel. It is important that the center speaker be

extremely accurate and mate well the front speakers,

and that it is recommended for use as a center speaker.

This is not the place to cut corners.

Surround Speakers

We recommend (along with the film industry) that the sur-

round speakers play down to at least 80 Hz. Surround

speakers contain the information that makes it appear

that planes are flying over your head. Some may suggest

that this is the place to save money and purchase a small,

inexpensive speaker. If you choose to do so, be prepared

to upgrade in the future as discrete multi-channel digital

encoding is proliferating rapidly and the demands on sur-

round speakers have increased.

Subwoofer

With any good surround system you will need one or

more high-quality subwoofers (the .1 in a 5.1 channel

surround system). Most movie soundtracks contain large

amounts of bass information as part of the special effects.

Good subwoofers will provide a foundation for the rest of

the system.

HOME THEATER

Figure 12. Summit speakers as front channels, the Stage as the center

channel, Script i speakers as side surround (effects) channels, and Descent

subwoofers as 0.1 (effects) channel.

Electrostatic Advantages 17

How can sound be reproduced by something that you are

able to see through? Electrostatic energy makes this possible.

Where the world of traditional loudspeaker technology

deals with cones, domes, diaphragms and ribbons that

are moved with magnetism, the world of electrostatic

loudspeakers deals with charged electrons attracting and

repelling each other.

To fully understand the electrostatic concept, some back-

ground information will be helpful. Remember when you

learned in a science or physics class that like charges repel

each other and opposite charges attract each other? Well,

this principle is the foundation of the electrostatic concept.

An electrostatic transducer consists of three pieces: stators,

the diaphragm and spacers (see figure 13). The diaphragm

is what actually moves to excite the air and create music.

The stator’s job is to remain stationary, hence the word

stator, and to provide a reference point for the moving

diaphragm. The spacers provide the diaphragm with a

fixed distance in which to move between the stators.

As your amplifier sends music signals to an electrostatic

speaker, these signals are changed into two high-voltage

signals that are equal in strength but opposite in polarity.

These high voltage signals are then applied to the stators.

The resulting electrostatic field, created by the opposing

high voltage on the stators, works simultaneously with

and against the diaphragm, consequently moving it back

and forth, producing music. This technique is known as

push-pull operation and is a major contributor to the sonic

purity of the electrostatic concept due to its exceptional

linearity and low distortion.

Since the diaphragm of an electrostatic speaker is uniform-

ly driven over its entire area, it can be extremely light and

flexible. This allows it to be very responsive to transients,

thus perfectly tracing the music signal. As a result, great

delicacy, nuance and clarity is possible. When you look

at the problems of traditional electromagnetic drivers,

you can easily see why this is so beneficial. The cones and

domes which are used in traditional electromagnetic driv-

ers cannot be driven uniformly because of their design.

Cones are driven only at the apex. Domes are driven at

their perimeter. As a result, the rest of the cone or dome

is just “along for the ride”. The very concept of these

drivers requires that the cone or dome be perfectly rigid,

damped and massless. Unfortunately, these conditions are

not available in our world today.

To make these cones and domes move, all electromagnet-

ic drivers must use voice coils wound on formers, spider

assemblies, and surrounds to keep the cone or dome in

position (see figure 14). These pieces, when combined

with the high mass of the cone or dome materials used,

make it an extremely complex unit with many weaknesses

and potential for failure. These faults contribute to the

high distortion products found in these drivers and is a

tremendous disadvantage when you are trying to change

motion as quickly and as accurately as a loudspeaker must

(40,000 times per second!).

ELECTROSTATIC ADVANTAGES

Figure 13. Cut away view of an XStat™ electrostatic transducer. Notice

the simplicity due to minimal parts usage.

Figure 14. Cut away view of a typical moving coil driver. Notice the com-

plexity due to the high number of parts.

18 Electrostatic Advantages

Another significant advantage of MartinLogan’s exclusive

transducer technology reveals itself when you look at exam-

ples of other loudspeaker products on the market today.

The Summit uses no crossover networks above 270 Hz

because they are not needed. The Summit consists of a

single, seamless electrostatic membrane reproducing all

frequencies above 270 Hz simultaneously. How is this

possible?

First we must understand that music is not composed

of separate high, mid and low frequency pieces. In fact,

music is comprised of a single complex waveform with all

frequencies interacting simultaneously.

The electrostatic transducer of the Summit essentially acts

as an exact opposite of the microphones used to record

the original event. A microphone, which is a single work-

ing element, transforms acoustic energy into an electrical

signal that can be amplified or preserved by some type

of storage media. The Summit’s electrostatic transducer

transforms electrical energy from your amplifier back into

acoustical energy.

Due to the limitations of electromagnetic drivers, no single

unit can reproduce the full range of frequencies. Instead,

these drivers must be designed to operate within a nar-

row, fixed bandwidth of the frequency range, and then

combined electrically so that the sum of the parts equals

the total signal. While nice in theory, we must deal with

real-world conditions.

In order to use multiple drivers, a crossover network

is enlisted to attempt a division of the complex musical

signal into the separate pieces (usually highs, mids, and

lows) that each specific driver was designed to handle.

Unfortunately, due to the phase relationships that occur

within all crossover networks and during the acoustical

recombination process, nonlinearities and severe deg-

radation of the music signal take place in the ear’s most

critical zone (see figure 15).

The Summit’s electrostatic transducer can single-handedly

reproduce all frequencies above 270 Hz simultaneously.

You have in one transducer the ability to handle in elegant

simplicity the critical frequencies above 270 Hz.

The crossover phase aberrations that are associated with

traditional tweeter, midrange, and woofer systems are

eliminated. The result is a dramatic improvement in imag-

ing and staging performance due to the minutely accurate

phase relationship of the full-range panel wave launch.

Full Range Operation

Figure 15. This diagram illustrates how a conventional

speaker system must use multiple crossover networks

that have negative effects on the musical performance.

XStat™ Transducer

XStat™ transducers incorporate a myriad of technology and

design innovations including CLS™, MicroPerf, Generation

2 Diaphragms, ClearSpars™, and Vacuum Bonding.

CLS™ (Curvilinear Line Source)

Since the beginning of audio, achieving smooth dispersion

has been a problem for all designers. Large panel transduc-

ers present unique challenge because the larger the panel,

the more directional the dispersion pattern becomes.

Wide range electrostats have long been one of the most

problematic transducers because they attain their full

range capabilities via a large surface area. It looked as if

they were in direct conflict to smooth dispersion and

almost every attempt to correct this resulted in either poor

dispersion or a serious compromise in sound quality.

After extensive research, MartinLogan engineers discovered

an elegantly simple solution to achieve a smooth pattern of

dispersion without degrading sound quality. By curving the

horizontal plane of the electrostatic transducer, a controlled

horizontal dispersion pattern could be achieved, yet the

purity of the almost massless electrostatic diaphragm

remained uncompromised. After creating this technology,

MartinLogan developed the production capability to bring

it out of the laboratory and into the market place. You will

find this proprietary MartinLogan technology used in all

of our electrostatic products. It is one of the many reasons

behind our reputation for high quality sound with prac-

tical usability. This is also why you see the unique “see

through” cylindrical shape of MartinLogan products.

Generation 2 Diaphragm

Summit’s diaphragm employs an extremely sophisticated

conductive coating applied to the polymer surface at an

atomic level using a plasma bonding process. A proprietary

compound is driven into the surface of the polymer film

in an oxygen free argon chamber. This process allows

extremely uniform surface resistivity characteristics, an

optically transparent surface, and a nearly massless dia-

phragm. This uniform surface resistivity controls the

electrostatic charge on the diaphragm surface and regulates

its migration. As a result, no discharging or “arcing” can occur.

Sleek. Compact. MicroPerf stator technology, featured in

all XStat™ transducers, reveals more open playable area

in each panel, offering increased performance from even

more compact stat panels. It is significant to note that the

XStat™ transducer in the radical new Summit loudspeaker

supports the bandwidth and dynamics associated with tra-

ditional electrostatic panels nearly twice its size.

Vacuum Bonding

To achieve the power, precision, and strength of the

XStat™ transducer, two insulated high-purity carbon steel

stators along with a proprietary plasma bonded diaphragm

and ClearSpar™ spacers are fused into a curved geometry

with an aerospace adhesive whose strength exceeds that

of welding. Our proprietary Vacuum Bonding process

guarantees uniform diaphragm tensioning and extremely

precise construction tolerances, resulting in unequivocal

precision, linearity and efficiency.

AirFrame™ Technology

Ultra-rigid, billet and extruded aerospace grade alumi-

num alloy AirFrame™ technology rigidifies and secures

the XStat™ electrostatic panel to the PoweredForce™

woofer cabinet while at the same time providing sonic

and electrical isolation. Advanced AirFrame™ technology

maximizes the electrostatic panels playable surface area

and dipole dispersion pattern while minimizing poten-

tially acoustically destructive intermodulated distortion

caused by spurious vibrations and resonance. The result?

Ultimate imaging capability, low-level detail resolution,

improved efficiency and overall accuracy.

PoweredForce™ Woofers

Through integrated engineering of advanced amplifi-

cation and transducer designs, PoweredForce™ bass

technology results in usable bass extension down to 24Hz,

immense bass dynamics and precision beyond the reach

of traditional massive box systems—all from an enclo-

sure not much larger than a case of wine! Additionally,

low-frequency equalization capabilities, integrated into

PoweredForce™ technology, allow precision calibration

for optimal room integration.

MartinLogan Exclusives 19

MARTINLOGAN EXCLUSIVES

MicroPerf Stator

20 Electrostatic History

In the late 1800’s, any loudspeaker was considered exotic.

Today, most of us take the wonders of sound reproduction

for granted.

It was 1880 before Thomas Edison had invented the

first phonograph. This was a horn-loaded diaphragm

that was excited by a playback stylus. In 1898, Sir Oliver

Lodge invented a cone loudspeaker, which he referred to

as a “bellowing telephone”, that was very similar to the

conventional cone loudspeaker drivers that we know today.

However, Lodge had no intention for his device to repro-

duce music because in 1898 there was no way to amplify

an electrical signal! As a result, his speaker had nothing to

offer over the acoustical gramophones

of the period. It was not until 1906

that Dr. Lee DeForrest invented the

triode vacuum tube. Before this, an

electrical signal could not be ampli-

fied. The loudspeaker, as we know it

today, should have ensued then, but

it did not. Amazingly, it was almost

twenty years before this would occur.

In 1921, the electrically cut phonograph record became

a reality. This method of recording was far superior to the

mechanically cut record and possessed almost 30 dB of

dynamic range. The acoustical gramophone couldn’t begin

to reproduce all of the information on this new disc. As a

result, further developments in loudspeakers were needed

to cope with this amazing new recording medium.

By 1923, Bell Telephone Laboratories made the decision

to develop a complete musical playback system consisting

of an electronic phonograph and a loudspeaker to take

advantage of the new recording medium. Bell Labs

assigned the project to two young engineers, C. W. Rice

and E. W. Kellogg.

Rice and Kellogg had a well equipped laboratory at their

disposal. This lab possessed a vacuum tube amplifier

with

an unheard of 200 watts, a large selection of the

new

electrically cut phonograph records and a variety of

loudspeaker prototypes that Bell Labs had been collecting

over

the past decade. Among these were Lodge’s cone, a

speaker

that used compressed air, a corona discharge (plas-

ma) speaker, and an electrostatic speaker.

After a short time, Rice and Kellogg had narrowed the field

of “contestants” down to the cone and the electrostat. The

outcome would dictate the way that future generations

would refer to loudspeakers as being either “conventional”

or “exotic”.

Bell Laboratory’s electrostat was something to behold. This

enormous bipolar speaker was as big as a door. The dia-

phragm, which was beginning to rot, was made of a pig

intestine that was covered with fine gold leaf to conduct

the audio signal.

When Rice and Kellogg began playing the new electrically

cut records through the electrostat,

they were stunned and impressed. The

electrostat performed splendidly. They

had never heard instrumental timbres

reproduced with such realism. This sys-

tem sounded like real music rather than

the honking, squawking rendition of the

acoustic gramophone. Immediately, they

knew they were on to something big.

The acoustic gramophone was destined to become obsolete.

Due to Rice and Kellogg’s enthusiasm, they devoted a

considerable amount of time researching the electrostatic

design. However, they soon encountered the same dif-

ficulties that even present designers face; planar speakers

require a very large surface area to reproduce the lower fre-

quencies of the audio spectrum. Because the management

at Bell Labs considered large speakers

unacceptable, Rice

and Kellogg’s

work on electrostatics would never be put to

use for a commercial product. Reluctantly, they advised the

Bell

management to go with the cone. For the next 30 years,

the electrostatic design lay dormant.

During the Great Depression of the 1930’s, consumer audio

almost died. The new electrically amplified loudspeaker

never gained acceptance, as most people continued to

use their old Victrola-style acoustic gramophones. Prior to

the end of World War II, consumer audio saw little, if any,

progress. However, during the late 1940’s, audio expe-

rienced a great rebirth. Suddenly there was tremendous

interest in audio products, and with that, a great demand

for improved audio components. No sooner had the cone

become established than it was challenged by products

developed during this new rebirth.

ELECTROSTATIC HISTORY

Rice and Kellogg had

narrowed the field of

“contestants down” to the

cone and the electrostat.

Page is loading ...

MartinLogan Summit User manual

Brand: MartinLogan

Model: Summit

Category: Soundbar speakers

Type: User manual

Download PDF

report

MartinLogan Summit User manual

MartinLogan Summit User manual

Related papers

Other documents