ECS A780GM-A ULTRA V1.0 User manual

Brand: ECS

Model: A780GM-A ULTRA V1.0

Category: Motherboards

Type: User manual

This manual is also suitable for

A780GM-A ULTRA

Preface

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any

particular purpose. The manufacturer reserves the right to revise this publication and

to make changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits govern-

ing this device. Changes or modifications not expressly approved by the system’s

manufacturer could void the user’s authority to operate the equipment.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

AMD, Phenom, Athlon, Sempron and Duron are registered trademarks of AMD

Corporation.

Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interfer-

ence that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur

le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

Describes features of the motherboard.

Go to

page 1

Describes installation of motherboard

components.

Go to

page 7

Provides information on using the BIOS

Setup Utility.

Go to

page 27

Describes the motherboard software

Go to

page 45

page 55

Chapter 5

Hybrid Graphics

Technology

Support

Describes the Hybrid Graphics

Technology

Go to

iii

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction............................................................................................1

Features...................................................................................................2

Motherboard Components...................................................................4

Chapter 2

7 7

Installing the Motherboard 7

Safety Precautions.............................................................................7

Choosing a Computer Case..............................................................7

Installing the Motherboard in a Case.............................................7

Checking Jumper Settings................................................................8

Setting Jumpers.........................................................................8

Checking Jumper Settings.........................................................9

Jumper Settings.........................................................................9

Installing Hardware..........................................................................10

Installing the Processor...........................................................10

Installing Memory Modules.....................................................11

Expansion Slots

.......................................................................15

Connecting Optional Devices..................................................17

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive......20

Installing a Floppy Diskette Drive...........................................21

Connecting I/O Devices..............................................................22

Connecting Case Components......................................................23

Front Panel Header..................................................................25

Chapter 3

27 27

Using BIOS 27

About the Setup Utility....................................................................27

The Standard Configuration..........................................................27

Entering the Setup Utility...............................................................27

Using BIOS.......................................................................................28

Standard CMOS Setup..................................................................29

Advanced Setup.............................................................................32

Advanced Chipset Setup................................................................34

Integrated Peripherals.................................................................35

Power Management Setup.............................................................36

PCI/PnP Setup..............................................................................37

PC Health Status...........................................................................38

M.I.B (MB Intelligent Bios)...........................................................40

Load Default Settings....................................................................42

Supervisor Password....................................................................42

User Password..............................................................................43

Save & Exit Setup .........................................................................43

Exit Without Saving.......................................................................43

Chapter 4

45 45

Using the Motherboard Software 45

About the Software CD-ROM.........................................................45

Auto-installing under Windows XP/Vista......................................45

Running Setup...............................................................................46

Manual Installation..........................................................................50

Utility Software Reference................................................................50

Chapter 5

55 55

Hybrid Graphics

Technology Support 55

Hybrid Graphics

Technology.........................................................55

Updating the BIOS.........................................................................44

Introducing the Motherboard

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the A780GM-A Ultra motherboard. This motherboard is a

high performance, enhanced function motherboard that supports socket for AMD

Phenom

processor (socket AM2+)/Athlon

64 X2 Dual-Core/Athlon

64/

Sempron

processors for high-end business or personal desktop markets.

There is an advanced full set of I/O ports in the rear panel, including PS/2 mouse and

keyboard connectors, one VGA port, one HDMI port, six USB ports, one ESATA

port, one optical SPDIFO port, one LAN port and audio jacks for microphone, line-

in and 6/8-channel High Definition Audio output.

The motherboard incorporates the AMD 780G Northbridge (NB) and SB750

Southbridge (SB) chipsets. The Northbridge supports the HyperTransport

3.0 in-

terface. The memory controller supports DDR2 memory DIMM frequencies of

1066*

(AM2+)/800/667/533/400. It supports four DDR2 slots with maximum

memory size of 32 GB*

. One PCI Express x16 slot, intended for Graphics Interface,

are fully compliant to the PCI Express Genaration 2.0 (version 2.0).

The SB750 Southbridge supports three PCI slots which are PCI 2.3 compliant. In

addition, two PCI Express x1 slots are supported, fully compliant to the PCI Express

Generation 2.0 (version 2.0). It integrates USB 2.0 interface, supporting up to

twelve functional ports (six USB ports and three USB 2.0 headers support additional

six USB ports). One onboard IDE connector supports two IDE devices in Ultra ATA

133/100/66/33 modes. The Southbridge integrates a Serial ATA host controller,

supporting six SATA ports with maximum transfer rate up to 3.0 Gb/s each.

1. Whether 1066 MHz memory speed is supported depends on the CPU

being used.

2. Currently, the memory maximum size we have tested is 8 GB (2 GB per

dimm).

Introducing the Motherboard

Feature

Processor

HyperTransport

Technology is a point-to-point link between two devices, it

enables integrated circuits to exchange information at much higher speeds than

currently available interconnect technologies.

• Accommodates AMD Phenom

processor (socket AM2+)

AMD Athlon

64 X2 Dual-Core/Athlon

64/Sempron™ processors

• Supports HyperTransport

(HT) 3.0 interface speeds

This motherboard uses a socket AM2+/AM2 that carries the following features:

AMD 780G

• One x4 A-Link Express II interface (PCI Express 1.1

compliant) for connection to an AMD Southbridge

• Supports one PCI Express x16 for Graphics Interface,

fully compliant to the PCI Generation 2.0 (version 2.0).

• Proven Radeon

graphics powering DirectX

• Enhanced Digital Display integration

• Fully ACPI 2.0, OnNow, and IAPC (Instantly Available

PC) power management

• Single chip solution in 55nm, 1.1 V CMOS technology

• Integrated ATI Hybrid Graphics, ATI Avivo

, ATI

PowerPlay

, Low Power Design, AMD Cool’nQuiet

2.0, ATI SurroundView

AMD OverDrive and AMD

RAIDXpert

The AMD 780G Northbridge (NB) and SB750 Southbridge (SB) chipsets are

based on an innovative and scalable architecture with proven reliability and

performance.

Chipset

SB750

• Compliant with PCI 2.3 specification at 33 MHz

• Supports six Serial ATA devices which speeds up to 3.0

Gb/s

• Complies with SATA 2.5 specification

• Supports both SATA 1.5 and SATA3.0 compliance de-

vices

• Supports AHCI hardware assist to support advanced

features such as NCQ ( Native Command Queuing), Hot

Plug, and Device or Host initiated power Management

(DIIPM/HIPM)

• Integrated USB 2.0 Host Controller supporting up to

twelve USB 2.0 ports

• Integrated IDE controller supports Ultra ATA 133/100/66/

33 modes

This board supports CPU up to 140W TDP only.

(SB)

(NB)

Memory

• Supports DDR2 1066 (AM2+)/800/667 DDR SDRAM with Dual-

channel architecture

• Accommodates four unbuffered DIMMs

• Up to 8 GB per DIMM with maximum memory size up to 32 GB*

Introducing the Motherboard

Onboard LAN

This motherboard supports Ultra DMA bus mastering with transfer rates of

133/100/66/33 MB/s.

Expansion Options

The motherboard comes with the following expansion options:

• One PCI Express x16 for Graphics Interface

• Two PCI Express x1 slots

• Three 32-bit PCI v2.3 compliant slots

• One IDE connector supporting up to two IDE devices

• One floppy disk drive interface

• Six 7-pin SATA connectors

• Supports PCI Express

1.1

• Integrated 10/100/1000 transceiver

• Wake-on-LAN and remote wake-up support

Integrated I/O

The motherboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• One VGA port

• One HDMI port

• One ESATA port

• Six USB ports

• One LAN port

• One optical SPDIFO port

• Audio jacks for microphone, line-in and 6/8-channel High Definition

Audio output.

BIOS Firmware

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

The firmware can also be used to set parameters for different processor clock

speeds.

The motherboard uses AMI BIOS that enables users to configure many system

features including the following:

Audio

• All DACs support 192K/96K/48K/44.1KHz DAC sample rate

• High-quality analog differential CD input

• Software selectable 2.5V/3.75V VREFOUT

• Meets Microsoft WLP 3.08 audio requirements

• Direct Sound 3D

compatible

1. Some hardware specifications and software items are subject to change

without prior notice.

2. Due to chipset limitation, we recommend that motherboard be operated in

the ambiance between 0 and 50°C.

Introducing the Motherboard

Motherboard Components

Introducing the Motherboard

Table of Motherboard Components

LABEL COMPONENTS

Socket for AMD Phenom

rocessor

(

socket AM2+

Athlon

64 X2 Dual-Core/Athlon

64/Sempron

processors

2. CPU_FAN CPU cooling fan connector

3. PWR_FAN2 Power cooling fan connector

4. DDR2_1~4 240-pin DDR2 SDRAM slots

5. ATX_POWE

Standard 24-

in ATX

ower connector

6. IDE Primary IDE connector

7. SPK Speaker header

8. PWR_FAN1 Power cooling fan connector

9. SATA1~6 Serial ATA connectors

10. CLR_CMOS Clear CMOS jumper

11. PWR_BTN Power on button

12. RST_BTN Reset button

13. F_PANEL Front panel switch/LED header

14. SPI_DEBUG SPI DEBUG header

15. F_USB1~3 Front Panel USB headers

16. FDD Floppy disk drive connector

17. SPDIFO SPDIF out header

18. F_AUDIO Front panel audio header

19. PCI1~3 32-bit add-on card slots

20. PCIEX16 PCI Express x16 slot for graphics interface

21. PCIE1~2 PCI Express x1 slots

22. SYS_FAN System cooling fan connector

23. ATX12V 8-pin +12V power connector

1. CPU Socket

This concludes Chapter 1. The next chapter explains how to install the motherboard.

Introducing the Motherboard

Memo

Installing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid dam-

age from static electricity

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies

with the specifications for the ATX system case. Firstly, some features on the

motherboard are implemented by cabling connectors on the motherboard to indica-

tors and switches on the system case. Make sure that your case supports all the

features required. Secondly, this motherboard supports one floppy diskette drive and

two enhanced IDE drives. Make sure that your case has sufficient power and space for

all drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O

template in the case matches the I/O ports installed on the rear edge of the

motherboard.

This motherboard carries an ATX form factor of 305 X 244 mm. Choose a case that

accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in

a case.

Most system cases have mounting brackets installed in the case, which correspond

the holes in the motherboard. Place the motherboard over the mounting brackets

and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion

slots on your motherboard.

Installing the Motherboard

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the jumper

caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When

the jumper cap is placed on both pins, the

jumper is SHORT. If you remove the jumper

cap, or place the jumper cap on just one pin,

the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins

1 and 2 are SHORT.

SHORT OPEN

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is

labeled.

Jumper Settings

To avoid the system unstability after clearing CMOS, we recommend

users to enter the main BIOS setting page to “Load Default Settings” and

then “Save Changes and Exit”.

Jumper Type Description

Setting (default)

CLR_CMOS

3-pin

Clear CMOS

1-2: NORMAL

2-3: CLEAR

Before clearing the

CMOS, make sure to

turn off the system.

CLR_CMOS

Installing the Motherboard

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure

that you DO NOT scratch the motherboard or any of the surface-

mount resistors with the clip of the cooling fan. If the clip of the

cooling fan scrapes across the motherboard, you may cause serious

damage to the motherboard or its components.

This motherboard has a socket AM2+/AM2 processor socket. When choosing a

processor, consider the performance requirements of the system. Performance is

based on the processor design, the clock speed and system bus frequency of the

processor, and the quantity of internal cache memory and external cache memory.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system

bus frequency for the processor. You may be able to change the settings in the system

Setup Utility. We strongly recommend that you do not over-clock processors or

other components to run faster than their rated speed.

On most motherboards, there are small surface-mount resistors near

the processor socket, which may be damaged if the cooling fan is

carelessly installed.

Avoid using cooling fans with sharp edges on the fan casing and the

clips. Also, install the cooling fan in a well-lit work area so that you

can clearly see the motherboard and processor socket.

1. Over-clocking components can adversely affect the reliability of the

system and introduce errors into your system. Over-clocking can per-

manently damage the motherboard by generating excess heat in com-

ponents that are run beyond the rated limits.

2. Always remove the AC power by unplugging the power cord from the

power outlet before installing or removing the motherboard or other

hardware components.

Warning:

Installing the Motherboard

1 Install your CPU. Pull up the lever away from

the socket and lift up to 90-degree angle.

2 Locate the CPU cut edge (the corner with

the pin hold noticeably missing). Align and

insert the CPU correctly.

3 Press the lever down and apply thermal

grease on top of the CPU.

4 Put the CPU Fan down on the retention mod-

ule and snap the four retention legs of the

cooling fan into place.

5 Flip the levers over to lock the heat sink in

place and connect the CPU cooling Fan power

cable to the CPUFAN connector. This com-

pletes the installation.

CPU Installation Procedure

The following illustration shows CPU installation components.

To achieve better airflow rates and heat dissipation, we suggest that you

use a high quality fan with 4800 rpm at least. CPU fan and heatsink

installation procedures may vary with the type of CPU fan/heatsink sup-

plied. The form and size of fan/heatsink may also vary.

Installing Memory Modules

This motherboard accommodates four memory modules. It can support four 240-pin

DDR2 1066 (AM2+)/800/667. The total memory capacity is 32 GB*.

DDR2 SDRAM memory module table

Do not remove any memory module from its antistatic packaging until you

are ready to install it on the motherboard. Handle the modules only by

their edges. Do not touch the components or metal parts. Always wear a

grounding strap when you handle the modules.

You must install at least one module in any of the four slots. Each module can be

installed with 8 GB of memory.

Memory module Memory Bus

DDR2 800 400 MHz

DDR2 1066 533 MHz

DDR2 667 333 MHz

The four DDR2 memory sockets (DDR2_1, DDR2_2, DDR2_3, DDR2_4) are di-

vided into two channels and each channel has two memory sockets as following:

Channel 0: DDR2_1, DDR2_2

Channel 1: DDR2_3, DDR2_4

Installing the Motherboard

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR2 SDRAM only.

2 Push the latches on each side of the DIMM slot down.

3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be

installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the

notches in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it

seats correctly. The slot latches are levered upwards and latch on to

the edges of the DIMM.

6 Install any remaining DIMM modules.

For best performance and compatibility, we recommend that users

install DIMMs in the sequence of DIMM3, DIMM4, DIMM1 and

DIMM2.

Recommend configuration for best performance and compatibility

* When Unganged Mode is disabled

Number of DIMMs DIMM 1 DIMM 2 DIMM 3 DIMM 4 AM2 AM2+ *

Single Channel

Unganged Mode

Dual Channel

Ganged Mode

Single Channel

Unganged Mode

Dual Channel

Ganged Mode

: operation with normal performance

: operation with the best performance

Installing the Motherboard

Table A: DDR2 (memory module) QVL (Qualified Vendor List)

The following DDR2 1066 (AM2+)/800/667 memory modules have been tested and

qualified for use with this motherboard.

Type Size Vendor Module Name

Apacer 78.91G92.9K5

Micron MT4HTF6464AY-667E1

PSC AL6E8E63J-6E1

Ramxel RML1520M38D6F-667

512 MB

Samsung K4T51083QC

78.01G9O.9K5

Elpida 1GB AM4B5708GEWS7E-0637F

Apacer

AU01GE667C5KBGC/Apacer/AM4B5708CPJS7E0810

Corsair VS1GB667D2/Corsair/64M8CFEG QIB0900721

Hexon HYNT7AUDR-30M48

Kingston KVR667D2N5/RAmos/RC12T083CA6-53EC

Micron MT8HTF12864AY-667E1

AL7E8E63B-6E1T

AL7E8F63J-6E1

PSC

AL7E8F73C-6E1

1 GB

Samsung

Gold bar M378T2863DZS 0742/SEC/ZCE6

K4T1G084QD

Aeneon AET860UD00-30DB08X

Apacer 78.A1G9O.9K4

Hexon HYNT8AUDR-30M88

Hynix HYMP125U64AP8-Y5-AB-A

Kingston KVR667D2N5

LeadMax LD 5PS1G831

PSC AL8E8F73C-6E1

DDR2 667

2 GB

Qimonda HYS64T256020EU-3S-C2

Installing the Motherboard

1.Due to the Phenom CPU and memory module limitation, the DRAM

may need to adjust the voltage for supporting DDR2 1066. The memory

modules which can be used stably are listed in the above QVL table for

reference.

Infineon HYS64T64020HU-2.5-A/Infineon/HYB18T256 800AF25

Kingston KVR800D2N5/512

Micron MT8HTF6464AY-80ED4

512 MB

Qimonda

HYS72T64000HU-2.5-

B/Qimonda/HYB18T512800BF25

A-DATA

M2GVD6G3I41P0U1E5E/A-DATA/VD29608A8D-

25EG-E0722

AET760UD00-25DC08X

Aeneon

AET760UD00-30DB97X/Aeneon/AET93R250B 0725

AU01GE800C5KBGC/Apacer/AM4B5708JQJS8E0749

Apacer

78.01GA0.9K5

Geil Geil Millenary/Geil/GL2L64M088BA18H

Hexon ELPT7AUDR-25M48

KHX6400D2ULK2/2G

Kingston

KVR800D2N5/1G

Ramaxel

RML1320EH38D7F-800/Elpida/E5108AHSE-8E-E

0705098L1

Samsung

Gold bar M378T2953EZ3-CE7 0726/SEC/ZCE7

K4T510830E

Silicon

Power

SP001GBLRU800S01

Smart DM080818-HY1/Hynix/HY5PS1G831CFP-S5 C822A

1 GB

Transcend Transcend/DIMM 5-5-5/Transcend/TQ123PGF8T0709

A-DATA Red A-DATA M2OMI6H3J4720L1C5Z/A-DATA/Boxed

Aeneon AET860UD00-25DC08X

Apacer 78.A1GA0.9K4

CORSAIR CORSAIR/CM2X2048-6400C5/CORSAIR/Boxed

Geil Platinum Edition/Geil/Boxed/2GB/DS

Hexon ELPT8AUDR-25M88

Kingston KVR800D2N5

Micron MT16HTF25664AY-800E1

PSC AL8E8F73C-8E1

Qimonda HYS64T256020EU-25F-C2

Samsung M378T5663QZ3-CF7/SEC/HCF7 K4T1G084QQ/DS

DDR2 800

2 GB

Silicon

Power

SP002GBLRU800S01

Type Size Vendor Module Name

512 MB

Kingston KVR1066D2N7/512

Kingston KVR1066D2N7/1G

Qimonda HYB18T512800CF19F

1 GB

Micron MT8HTF12864AY-1GAE1

DDR2 1066

2 GB

Micron DMT16HTF25664AY-1GAE1

2.DDR2 1066 is supported when using socket AM2+ CPU.

Page is loading ...

ECS A780GM-A ULTRA V1.0 User manual

Brand: ECS

Model: A780GM-A ULTRA V1.0

Category: Motherboards

Type: User manual

This manual is also suitable for

A780GM-A ULTRA

Download PDF

report

ECS A780GM-A ULTRA V1.0 User manual

This manual is also suitable for

ECS A780GM-A ULTRA V1.0 User manual

Related papers

Other documents