Sangean Electronics RCR-1 User manual

RCR-1

Operating instruction

Instruccions de manejo

GB

E

WARNING:

TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW-

HEAD WITHIN THE

TRIANGLE IS A WARN-

ING SIGN ALERTING

YOU OF “DANGEROUS

VOLTAGE” INSIDE THE

RADIO.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC

SHOCK, DO NOT REMOVE

THE BACK, NO USER SER-

VICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE PER-

SONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A WARN-

ING SIGN ALERTING

YOU OF IMPORTANT

INSTRUCTIONS

ACCOMPANYING THIS

RADIO.

!

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your

outlet. consult an electrician for replacement of the obsolete outlet.

1

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged. liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. To Reduce the Risk of Fire or Electric Shock, Do not Expose

This Appliance To Rain or Moisture.

16. The Shock Hazard Marking and Associated Graphical Symbol is

provided on the bottom panel of unit.

17. Apparatus shall not be exposed to dripping or splashing and no

objects filled with liquids, shall not be placed on the apparatus.

2

GB

Main features

(1) LW/MW/FM radio

With automatic station memory programming (ATS)

(2) Analog clock with radio controlled time device

(3) 21 station memories

(4) Digital radio controlled clock with date display

Date and time displays are checked and if necessary corrected daily

with an exact radio controlled time antenna signal

(5) Nap timer

Adjustable from 10-120 minutes

(6) Alarm with Humane Wake System ( HWS )

The alarm begins quietly and gradually becomes louder before

switched off

(7) Radio alarm

Woken up by the favorite station

(8) Two independent alarm functions

(9) Alarm week day selection

3

(10) Adjustable alarm level

(11) Display brightness adjustment

(12) Headphone jack

(13) Tone Control

(14) Time Zone adjustment (-1 , 0 , +1 , +2 )

4

GB

Page is loading ...

6

GB

Controls

Power on/off and Sleep timer

Headphones socket

Nap timer

Display backlight control

Volume Control

Analog clock

High/Low tone control

Display brightness adjustment

Alarm level adjustment ( radio and buzzer )

Time Zone adjustment

RESET

Date adjustment

Time adjustment

Alarm 2 button

Alarm 1 button

Time/Date/Alarm set and ATS function button

Display

Tuning Up/Down and SNOOZE button

Station memories and alarm week days selection

LW/MW/FM band and alarm mode selection also Daylight Saving

Time (D.S.T.) set

10

1

2

3

4

5

6

7

8

9

11

12

13

14

15

16

17

18

19

20

7

LCD display

Radio band and a.m./p.m. display

Time set

Daylight Saving Time (D.S.T.)

Alarm indicator

Sleep timer

Nap timer

Alarm a.m./p.m. indicator

Date

Week day

Month/Date/Year/alarm time

Radio controlled symbol

ATS ( Auto Tuning System ) status

Station memory number and second indicator

Minute ( for Nap and Sleep timer )

Frequency/Time display

A

C

B

D

E

F

G

H

I

J

K

L

M

N

O

8

GB

NOTES ON SAFETY

THIS PRODUCT OPERATES ON 110-120 VOLT/50-60 Hz power

source. If this product will not be used for any extended period of

time it is suggested that the power cord be removed from the AC

power supply.

Protect this product from excessive heat and moisture.

If this product should ever require servicing please return to an

authorized Sangean Service center. Do not open this product

yourself or allow it to be opened by an unauthorized service facility.

CLOCK RADIO OPERATION

Automatic Station Memory Programming (ATS)

Upon initial connection to an AC power source the ATS system will

automatically move the analog clock to 12:00 and automatically set

up all the 7 AM and 7 FM memory presets based upon the signal

strength of the incoming stations.

9

ATOMIC CLOCK OPERATION

The Sangean RCR1 consists of a crystal controlled clock movement

which includes a very special AM radio receiver that is tuned to

receive the 60kHz WWVB time signal broadcast from the U.S.

Government’s Atomic Clock in Boulder, Colorado. The signal is an

AM radio signal and as such is susceptible to weather conditions,

electrical interferences, solar conditions and the position of the

clock’s antenna all of which effects the receiver’s reception. As a

general rule, best reception is at night and just before or after sunrise

or sunset. Although the clock can work in most locations the number

of times that it adjusts itself to the U.S. Atomic Clock’s time signal

may depend on its location. Under certain weather conditions or in

areas of poor reception it may take 48 hours or more to receive a

signal for the correct time. In some cases it may be necessary to

seek another location in order to receive a useable time signal.

Set time Zone Switch [10] located on bottom of clock to your correct

zone as illustrated.

After the ATS program completes the AM/FM frequency set up the

following display — : — will appear and the symbol will blink

indicating the radio is searching for the radio controlled signal.

Once the radio receives the radio controlled signal the correct time

and date will be set automatically. Once the correct time and date

have been set, the symbol will stop blinking but the symbol will

remain on the display indicating that the time and date have been

set utilizing the radio controlled signal. The analog clock will follow

the radio controlled signal.

10

GB

MANUAL TIME ADJUSTMENT

Press Time [13] button and display will flash and previous time

will be displayed.

Press Set [16] button, the hour digits on the display will begin to

flash.

Set the hour using the + or – key [18]

Press the Set [16] button once again and the minutes digits will start

to blink on the display. Set minutes as you set hour.

Press Time [13] button to confirm time setting with a beep.

The analog clock will now adjust to the digital time displayed and the

seconds start to count. The symbol will appear indicating that this

time has not been set by the Atomic Clock but is a manual setting.

Note: If your area is on Daylight Saving Time press the Mode

[20] button once to advance the time seting 1 hour. Display will

show indicating D.S.T. time.

DATE ADJUSTMENT

Press Date button [12], date display will blink.

Press Set button [16], display will blink with the current year setting,

a beep and a small y at the end of the blinking year.

Set the year with + or – key [18]

Press Set button once again for month and date setting.

Set month and date as you set year.

Press Date button again to confirm setting.

The display should now show the correct time, date, week day,

second and the symbol should again appear showing that you

have set the clock manually.

11

RADIO OPERATION

Turn on the radio by pressing the Power on/off key [1]

Tuning Desired Stations

Manual Station Selection… ..

Using + or - Tuning Button [18] tune to the desired station.

Automatic Station Selection… ..

Press and hold + or – Tuning Button [18] for more then ½ second and

release. The radio will search for the next active station.

Automatic Station Memory Programming (ATS)

When the radio is first activated the ATS feature will automatically

select, based upon signal strength, 7 AM and 7 FM stations and

automatically position them into the associated presets.

If you wish to repeat this process, select the desired band by

pressing band selection button [20] and then pressing and holding

the ATS button [16] for more then 4 seconds.

Manual Station Memory Programming

Select desired frequency using Manual Station Selection

Press and hold desired preset button for more then 2 seconds until

a beep is heard and M stops blinking

The selected station is now stored in the desired preset position.

When you store a new station in a preset memory slot, the station

previously in that slot is automatically erased.

12

GB

Recalling Memory Presets

Select band by pressing Band selector button [20]

Select memory preset buttons 1-7 for desired station

Volume

Volume can be adjusted using Volume control [5]

Tone Control

Adjust desired tone using Tone Control [7]

ALARM CLOCK OPERATION

Alarm settings can be made with clock/radio on or off.

The Alarm Clock/Radio is equipped with two independent alarm

systems each of which can activate the Human Wake System Buzzer

or turn on a preselected radio station.

13

Using Alarm with a Preselected Radio Station

Select desired station using + or – Tuning Button [18] or select one

of the 1-7 presets.

Set the desired volume level using Alarm Level Adjustment [9]

Select alarm system 1 or 2 by pressing the alarm button [14] or [15].

Display will blink with selected alarm

Press alarm set button [16]

Display will blink showing selected alarm hour and alarm mode

and beep

Press alarm Mode button [20] to select alarm mode

Use + or – button [18] to set alarm time hours.

Press set button [16] to set minutes using + or – button to

set minutes.

Press alarm days selections 1-7 (Sunday-Saturday) to select

alarm days.

Display will show the days on which you wish to be awoken by the

radio alarm.

Pressing alarm button 1 or 2 will confirm settings and a beep and

display indicates radio alarm is set.

Note:

If alarm days or alarm mode are not selected display will blink

all the days for a few seconds indicating the alarm is not set

and the alarm will not be activated.

If you would like to be awoken to the station you are presently

listening to press alarm button 1 or 2 for more then 2 seconds.

This allows the station you are listening to be stored into

memory. Then follow above procedures

14

GB

Using Alarm with HWS Alarm Beep

Select alarm system 1 or 2 by pressing the alarm button [14] or [15].

Display will blink with selected alarm Press alarm set button [16]

Display will blink showing selected alarm hour and alarm mode

and beep

Press alarm Mode button [20] to select alarm mode

Use + or – button [18] to set alarm time hours.

Press set button [16] to set minutes using + or – button to

set minutes

Press alarm days selections 1-7 (Sunday-Saturday) to select

alarm days.

Display will show the days on which you wish to be awoken by the

buzzer humane alarm

Pressing alarm button 1 or 2 will confirm settings and a beep and

display indicates buzzer humane alarm is set.

Note:

If alarm days or alarm mode are not selected display will blink

all the days for a few seconds indicating the alarm is not set

and the alarm will not be activated.

15

Cancelling Alarm Setting

Alarm functions can be cancelled:

Select alarm system 1 or 2 by pressing the alarm button [14] or [15].

Display will blink with selected alarm

Press alarm set button [16]

Display will blink showing selected alarm hour and alarm mode

and beep

Press alarm Mode button [20] one or two times (depending if you

were in the alarm radio or alarm buzzer mode) till display blinks.

Press alarm 1 or 2 button again to confirm alarm cancellation.

The symbol will stay on the display for about 2 seconds

and disappear.

You may also select days you wish to be or not to be woken after

pressing the Set button while display is blinking. Press 1-7

(Sunday-Saturday) of button [19] to make a selection.

SNOOZE CONTROL

Pressing the Snooze button [19] interrupts the radio or beep tone/

HWS alarm for 5 minutes. The alarm will start up after 5 minutes and

will continue unless interrupted again. The alarm will continue for 1

hour if not interrupted.

CANCELLING THE ALARM SIGNAL

To cancel an alarm totally it is only necessary to press power button

[1]

16

GB

NAP TIMER

The Nap timer button [3] allows you to adjust the interval from 10-120

minutes in 10 minute steps before the alarm signal starts. If you wish

to turn off the Nap timer before the time is up simply adjust the

number of remaining minutes by pressing NAP key to off and

release. NAP will disappear from the display. The NAP timer may be

turned off by pressing Power key [1]

SLEEP AUTO SHUT OFF

Pressing and holding the power button [1] will activate the sleep

function. This function steps in 15 minute increments. This Sleep

function will turn off the radio at the pre-selected time. Pressing the

power button [1] will turn off function.

HEADPHONES

A jack is provided to allow headphone usage. When headphones are

used the internal speaker is disconnected.

ALARM LEVEL ADJUSTMENT

An alarm level control [9] is provided on the bottom of the radio.

DISPLAY BACKLIGHT CONTROL

Button [4] allows two step adjustment of display brightness

DISPLAY BRIGHTNESS ADJUSTMENT

With display backlight control in dark position, Display Brightness

Adjustment [8] may be used to fine tune display brightness.

17

TIME ZONE SWITCH

Time Zone Switch [10] should be set to zone where clock/radio is to

be used.

TROUBLESHOOTING/RESET

If the radio fails to operate correctly or some of the digits on the

display are missing or incomplete the following may correct the

problem:

Using a suitable implement (the end of a paper clip), press the

RESET button [11] for a few seconds. This will reset the

microprocessor, clock time and clear all the stations stored in preset

memory.

TECHNICAL DATA

Power Supply 110-120 Volt/50-60 Hz, 800mW max

Frequency Coverage FM 87.50 - 108.0 MHz

AM 520 - 1710 kHz

Page is loading ...

Sangean Electronics RCR-1 User manual

Sangean Electronics RCR-1 User manual

in other languages

Related papers

Other documents