Motorola LS1203 Quick Reference Manual

Symbol LS1203

Quick Reference Guide

2 Symbol LS1203

reserved.

Motorola reserves the right to make changes

to any product to improve reliability, function,

or design.

Motorola does not assume any product liability

arising out of, or in connection with, the

application or use of any product, circuit, or

application described herein.

No license is granted, either expressly or by

implication, estoppel, or otherwise under any

patent right or patent, covering or relating to

any combination, system, apparatus,

machine, material, method, or process in

which Motorola products might be used. An

implied license exists only for equipment,

circuits, and subsystems contained in Motorola

products.

MOTOROLA, the Stylized M Logo and Symbol

and the Symbol logo are registered

trademarks of Motorola, Inc. Other product

names mentioned in this manual may be

trademarks or registered trademarks of their

respective companies and are hereby

acknowledged.

Motorola, Inc.

One Motorola Plaza

Holtsville, N.Y. 11742-1300

http://www.motorola.com/enterprisemobility

Warranty

For the complete Motorola hardware product

warranty statement, go to:

http://www.motorola.com/enterprisemobility/warranty

Patents

This product is covered by one or more

patents. For patent information go to:

http://www.motorola.com/enterprisemobility/patents

3

Connect/Disconnect

Cable

Connect Host Interface

Keyboard Wedge Interface

RS-232 Interface

USB Interface

1

2

4 Symbol LS1203

Aim and Scan

3

012345

5

Triggered/Auto-scan Modes

NOTE See Scanning Modes

on page 6.

TRIGGERED MODE

1

2

AUTO-SCAN MODE

1

2

6 Symbol LS1203

Parts of the Scanner

Scanning Modes

The scanner can operate in two modes:

•

Triggered mode - trigger button must be

pressed to emit the laser in order to a

scan bar code.

or

•

Auto-scan mode - scanner laser is in

constant on state and no trigger button

press is required to scan a bar code.

To toggle between modes, scan

TRIGGERED/AUTO-SCAN bar codes on

page 5.

For example, if the scanner is in triggered

mode, scan AUTO-SCAN MODE to switch

to auto-scan mode. If the scanner is in

auto-scan mode, scan TRIGGERED

MODE to switch to triggered mode.

NOTE When the scanner is

not used for an extended

period of time in auto-scan

mode, it enters sleep mode.

To wake the scanner, press

the trigger button.

LED

Trigger

Button

Scan

Window

7

Troubleshooting

Problem Possible

Cause

Possible

Solutions

Nothing

happens

when the

scan button

is pulled.

No power to

the scanner.

Check system

power. Ensure

power supply is

connected.

Interface or

power

cables are

loose.

Ensure all cable

connections are

secure.

Laser

comes on,

but symbol

does not

decode.

Scanner not

programmed

for correct

bar code

type.

Ensure scanner

is programmed

to read the type

of bar code

scanned. Refer

to the Symbol

LS1203

Product

Reference

Guide, p/n

72E-73953-xx,

for more

information.

Bar code

symbol is

unreadable.

Check the

symbol to

ensure it is not

defaced. Try

scanning

another bar

code type.

Distance

between

scanner and

bar code is

incorrect.

Move scanner

closer to or

further from the

bar code.

Symbol is

decoded but

not

transmitted

to the host.

Scanner not

programmed

for the

correct host

type.

Scan the

appropriate

host type bar

code.

8 Symbol LS1203

Beeper Definitions

The scanner issues different beep

sequences and patterns to indicate status.

The table below defines beep sequences

that occur during both normal scanning and

while programming the scanner.

NOTE For detailed

troubleshooting, refer to the

Symbol LS1203 Product

Reference Guide, p/n

72E-73953-xx.

Beeper

Sequence

Indication

Standard Use

Low/medium/high

beep

Power up.

Short high beep A bar code symbol was

decoded (if decode beeper

is enabled).

4 long low beeps A transmission error was

detected in a scanned

symbol. The data is

ignored. This occurs if a

unit is not properly

configured. Check option

setting.

5 low beeps Conversion or format

error.

Low/high/low

beep

ADF transmit error.

High/high/high/

low beep

RS-232 receive error.

Parameter Menu Scanning

Short high beep Correct entry scanned or

correct menu sequence

performed.

9

Low/high beep Input error, incorrect bar

code or Cancel scanned,

wrong entry, incorrect bar

code programming

sequence; remain in

program mode.

High/low beep Keyboard parameter

selected. Enter value

using bar code keypad.

High/low/high/

low beep

Successful program exit

with change in the

parameter setting.

Low/high/low/

high beep

Out of host parameter

storage space. Scan SET

DEFAULTS on page 86.

Code 39 Buffering

High/low beep New Code 39 data was

entered into the buffer.

3 beeps - long

high beep

Code 39 buffer is full.

Low/high/low

beep

The Code 39 buffer was

erased or there was an

attempt to clear or transmit

an empty buffer.

Low/high beep A successful transmission

of buffered data.

Host Specific

USB only

4 short high

beeps

Scanner has not

completed initialization.

Wait several seconds and

scan again.

Scanner gives a

power-up beep

after scanning a

USB Device

Type.

Communication with the

bus must be established

before the scanner can

operate at the highest

power level.

Beeper

Sequence

Indication

10 Symbol LS1203

LED Definitions

In addition to beeper sequences, the

scanner communicates with the user using

a two-color LED display. The table below

defines LED colors that display during

scanning.

Programming Bar Codes

Descriptions

This guide includes the programming bar

codes required to set up the scanner to

work with various host interfaces. Some

frequently used programming bar codes

are also included.

For all programming bar codes and detailed

information about the scanner, go to:

http://www.symbol.com/services/manuals

The power-up

beep occurs

more than once.

The USB bus may put the

scanner in a state where

power to the scanner is

cycled on and off more

than once. This is normal

and usually happens when

the host PC cold boots.

RS-232 only

1 short high beep A <BEL> character is

received and Beep on

<BEL> is enabled.

LED Indication

Off No power is applied to the scanner,

or the scanner is on and ready to

scan.

Green A bar code was successfully

decoded.

Red A data transmission error or

scanner malfunction occurred.

Beeper

Sequence

Indication

11

and download the latest version of the

Symbol LS1203 Product Reference Guide.

The definitions that follow briefly explain the

programming bar codes that begin on page

86.

Set Defaults

Scan Set Defaults on page 86 to set all

parameters to their default values.

Host Interfaces

NOTE Cables may vary depending on

configuration.

Keyboard Wedge Interface

To use a Keyboard Wedge interface, scan

IBM PC COMPATIBLES page 86. Then

scan the appropriate Country Keyboard

Type (country code).

RS-232 Interface

To use an RS-232 interface, scan an

RS-232 host type beginning on page 88.

USB Interface

The scanner attaches directly to a USB

host, or a powered USB hub, and is

powered by it. No additional power supply

is required. When using a USB interface,

the scanner auto detects the USB and

defaults to the HID keyboard interface. For

additional USB hosts, see page 88.

Page is loading ...

86 Symbol LS1203

Programming Bar Codes

Keyboard Wedge

Interface

Country Keyboard Types

(Country Codes)

SET DEFAULTS

IBM PC/AT and IBM PC

COMPATIBLES

IBM PS/2 (MODEL 30)

2

5001

5002

5003

5004

5005

5006

5007

5008

5009

5010

7009

7008

7013

7012

7004

7011

7003

7002

7014

NORTH AMERICAN (Default)

FRANÇAIS/FRENCH Windows

FRANÇAIS CANADIAN/

FRENCH CANADIAN Windows 95/98

1

Page is loading ...

88 Symbol LS1203

RS-232 Interface

USB Interface

STANDARD RS-232

ICL RS-232

NIXDORF RS-232 MODE A

NIXDORF RS-232 MODE B

FUJITSU RS-232

OPOS

HID KEYBOARD EMULATION

IBM HAND-HELD USB

89

Carriage Return/Line Feed

Set Scan Data Transmission Format

Cancel

SCAN OPTIONS

ENTER

CANCEL

90 Symbol LS1203

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential

risk of ergonomic injury follow the

recommendations below. Consult with your local

Health & Safety Manager to ensure that you are

adhering to your company’s safety programs to

prevent employee injury.

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within

easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures.

Regulatory Information

All Symbol devices are designed to be compliant

with rules and regulations in locations they are sold

and will be labeled as required.

Any changes or modifications to Symbol

Technologies equipment, not expressly approved

by Symbol Technologies, could void the user's

authority to operate the equipment.

Power Supply

Note: Use only a Symbol-approved power supply

(p/n KT-14001-001R, 50-14000-009 or

50-14000-010) output rated 5 VDVC and minimum

650mA. The power supply is certified to EN60950

with SELV outputs. Use of alternative power supply

will invalidate any approval given to this device and

may be dangerous.

Hinweis: Benutzen Sie nur eine von Symbol

Technologies genehmigte Stromversorgung

(Teilenr. KT-14001-001R, 50-14000-009,

50-14000-010) mit einer Ausgangsleistung von 5

VDC (Gleichstrom) und mindestens 650mA. Die

Stromversorgung ist nach EN60950 für die

Verwendung in SELV-Stromkreisen zertifiziert. Bei

Verwendung eines anderen Netzteils werden alle

für das Gerät gewährten Genehmigungen außer

Kraft gesetzt, und der Betrieb kann gefährlich sein.

91

Radio Frequency Interference

Requirements

Note: This equipment has

been tested and found to

comply with the limits for a

Class B digital device,

pursuant to Part 15 of the FCC

rules. These limits are designed to provide

reasonable protection against harmful interference

in a residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance

with the instruction manual, may cause harmful

interference to radio communications. However

there is no guarantee that interference will not

occur in a particular installation. If the equipment

does cause harmful interference to radio or

television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Radio Frequency Interference

Requirements - Canada

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

Marking and European

Economic Area (EEA)

Statement of Compliance

Symbol Technologies, Inc., hereby

declares that this device is in

compliance with all the applicable

Directives, 89/336/EEC, 73/23/EEC. A

Declaration of Conformity may be

obtained from

http://www2.symbol.com/doc/.

Tested to comply

with FCC Standards

FOR HOME OR OFFICE USE

92 Symbol LS1203

Japan (VCCI) - Voluntary Control

Council for Interference

This is a Class B product based on the standard of

the Voluntary Control Council for Interference from

Information Technology Equipment (VCCI). If this

is used near a radio or television receiver in a

domestic environment, it may cause radio

interference. Install and use the equipment

according to the instruction manual.

Laser Devices

Symbol devices using lasers comply

with 21CFR1040.10 and 1040.11

except for deviations pursuant to Laser

Notice No. 50, dated July 26, 2001 and

EN60825-1:1994+ A1:2002 +A2:2001,

IEC60825-1:1993+A1:1997+A2:2001.

The laser classification is marked on one of the

labels on the device.

Class 1 Laser devices are not considered to be

hazardous when used for their intended purpose.

The following statement is required to comply with

US and international regulations:

Caution: Use of controls, adjustments or

performance of procedures other than those

specified herein may result in hazardous laser light

exposure.

Class 2 laser scanners use a low power, visible

light diode. As with any very bright light source,

such as the sun, the user should avoid staring

directly into the light beam. Momentary exposure to

a Class 2 laser is not known to be harmful.

Recommandations

ergonomiques

Attention : pour éviter ou minimiser le risque

potentiel d'une blessure ergonomique, respectez

les recommandations suivantes. Consultez votre

responsable local de l'hygiène, de la santé et de la

sécurité, pour vous assurer que vous respectez les

consignes de sécurité de votre entreprise, qui ont

pour but d'éviter toute blessure d'employé.

Ǩȃ㺙㕂Ȅǃᚙฅ޺⧚㺙㕂ㄝ䳏⊶䱰ᆇ㞾Џ㽣ࠊन䅄Ӯ˄˲˟˟˥˅

ȃ෎⑪Ȁ෎ǺǤȷɱɁ

Bᚙฅᡔ㸧㺙㕂ǼǮǄǨȃ㺙㕂Ȅǃ

ᆊᒁ⪄๗ǼՓ⫼ǮȠǨǽȧⳂⱘǽǬǻǙȓǮǡǃǨȃ㺙㕂ǡɱ

ɀȲșɎɴɛɀɯɻফֵ″Ȁ䖥᥹ǬǻՓ⫼ǪȡȠǽǃ

ফֵ䱰ᆇȧᓩǢ䍋ǨǮǨǽǡǗȟȓǮǄ

পᡅ䂀ᯢ᳌ȀᕧǸǻℷǬǙপȟᡅǙȧǬǻϟǪǙǄ

Page is loading ...

95

Marquage et zone économique

européenne (ZEE)

Déclaration de conformité

Symbol Technologies, Inc., déclare par

la présente que cet appareil est

conforme à toutes les Directives

89/336/CEE et 73/23/CEE. Vous

pouvez obtenir une déclaration de

conformité en vous adressant à

http://www2.symbol.com/doc/.

Japan (VCCI) - Voluntary Control

Council for Interference

This is a Class B product based on the standard of

the Voluntary Control Council for Interference from

Information Technology Equipment (VCCI). If this

is used near a radio or television receiver in a

domestic environment, it may cause radio

interference. Install and use the equipment

according to the instruction manual.

Appareils lasers

Les appareils Symbol à rayons laser

sont conformes aux normes

américaines 21CFR1040.10 et 1040.11

à l'exception des déviations

conformément à l'avertissement laser No.50, du 26

juillet 2001 et des normes européennes

EN60825-1:1994+ A1:2002 +A2:2001,

IEC60825-1:1993+A1:1997+A2:200 .

La classification des rayons lasers figure sur l'une

des étiquettes de l'appareil.

Les appareils à rayons laser de classe 1 ne sont

pas considérés comme dangereux, à condition de

les utiliser pour les activités prévues. La

déclaration suivante est nécessaire pour respecter

les réglementations américaines et

internationales:

Attention : L'utilisation de commandes, réglages

ou procédures autres que ceux qui sont spécifiés

dans ce document risque d'entraîner une

exposition dangereuse à des rayons laser.

Ǩȃ㺙㕂Ȅǃᚙฅ޺⧚㺙㕂ㄝ䳏⊶䱰ᆇ㞾Џ㽣ࠊन䅄Ӯ˄˲˟˟˥˅

ȃ෎⑪Ȁ෎ǺǤȷɱɁ

Bᚙฅᡔ㸧㺙㕂ǼǮǄǨȃ㺙㕂Ȅǃ

ᆊᒁ⪄๗ǼՓ⫼ǮȠǨǽȧⳂⱘǽǬǻǙȓǮǡǃǨȃ㺙㕂ǡɱ

ɀȲșɎɴɛɀɯɻফֵ″Ȁ䖥᥹ǬǻՓ⫼ǪȡȠǽǃ

ফֵ䱰ᆇȧᓩǢ䍋ǨǮǨǽǡǗȟȓǮǄ

পᡅ䂀ᯢ᳌ȀᕧǸǻℷǬǙপȟᡅǙȧǬǻϟǪǙǄ

Page is loading ...

98 Symbol LS1203

Funkfrequenzen auswirken. Eine Gewährleistung,

dass bei einer bestimmten Installation keine

Störungen auftreten, kann nicht gegeben werden.

Sollte das Gerät Störungen beim Radio- oder

TV-Empfang verursachen, die durch Aus- und

Einschalten des Geräts erkannt werden können,

sollten die Störungen durch eine oder mehrere der

folgenden Maßnahmen behoben werden:

• Neuausrichtung oder Umstellung der

Empfangsantenne

• Vergrößerung des Abstands zwischen Gerät

und Empfänger

• Anschluss des Geräts an eine andere

Steckdose als die, an der der Empfänger

angeschlossen ist

• Beratung durch den Händler oder einen

Radio-/Fernsehtechniker

Radio Frequency Interference

Requirements – Canada

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

Zeichen und der europäische

Wirtschaftsraum (EWR)

Konformitätserklärung

Symbol Technologies, Inc. erklärt

hiermit, dass dieses Gerät allen

anwendbaren Richtlinien, 89/336/EEC,

73/23/EEC, entspricht. Eine

Konformitätserklärung kann unter

http://www2.symbol.com/doc/

heruntergeladen werden.

Japan (VCCI) - Voluntary Control

Council for Interference

This is a Class B product based on the standard of

the Voluntary Control Council for Interference from

Information Technology Equipment (VCCI). If this

Ǩȃ㺙㕂Ȅǃᚙฅ޺⧚㺙㕂ㄝ䳏⊶䱰ᆇ㞾Џ㽣ࠊन䅄Ӯ˄˲˟˟˥˅

ȃ෎⑪Ȁ෎ǺǤȷɱɁ

Bᚙฅᡔ㸧㺙㕂ǼǮǄǨȃ㺙㕂Ȅǃ

ᆊᒁ⪄๗ǼՓ⫼ǮȠǨǽȧⳂⱘǽǬǻǙȓǮǡǃǨȃ㺙㕂ǡɱ

ɀȲșɎɴɛɀɯɻফֵ″Ȁ䖥᥹ǬǻՓ⫼ǪȡȠǽǃ

ফֵ䱰ᆇȧᓩǢ䍋ǨǮǨǽǡǗȟȓǮǄ

পᡅ䂀ᯢ᳌ȀᕧǸǻℷǬǙপȟᡅǙȧǬǻϟǪǙǄ

Page is loading ...

101

obstante, no se garantiza que la interferencia no se

produzca en una instalación determinada. Si el

equipo provoca interferencias en la recepción de

señales de radio o televisión (lo que se puede

averiguar encendiendo y apagando el equipo), se

aconseja al usuario que intente corregir la

interferencia a través de una o varias de las

siguientes medidas:

• Cambie la orientación o la ubicación de la

antena receptora.

• Aumente la separación entre el equipo y el

receptor.

• Conecte el equipo a una toma de un circuito

distinto del utilizado actualmente para la

conexión del receptor.

• Consulte al distribuidor o a un técnico

cualificado de radio / TV para obtener ayuda.

Requisitos sobre interferencias

de radiofrecuencia: Canadá

Este aparato digital de Clase B cumple con la

normativa canadiense ICES-003.

Cet appareil numérique de la classe B est

conforme à la norme NMB-003 du Canada.

Marcas del Espacio Económico

Europeo (EEE)

Declaración de conformidad

Symbol Technologies, Inc. declara que

este dispositivo cumple las

especificaciones de las directivas

pertinentes, 89/336/CEE, 73/23/CEE.

La declaración de conformidad se

puede obtener en

http://www2.symbol.com/doc/.

Japan (VCCI) - Voluntary Control

Council for Interference

This is a Class B product based on the standard of

the Voluntary Control Council for Interference from

Information Technology Equipment (VCCI). If this

is used near a radio or television receiver in a

Ǩȃ㺙㕂Ȅǃᚙฅ޺⧚㺙㕂ㄝ䳏⊶䱰ᆇ㞾Џ㽣ࠊन䅄Ӯ˄˲˟˟˥˅

ȃ෎⑪Ȁ෎ǺǤȷɱɁ

Bᚙฅᡔ㸧㺙㕂ǼǮǄǨȃ㺙㕂Ȅǃ

ᆊᒁ⪄๗ǼՓ⫼ǮȠǨǽȧⳂⱘǽǬǻǙȓǮǡǃǨȃ㺙㕂ǡɱ

ɀȲșɎɴɛɀɯɻফֵ″Ȁ䖥᥹ǬǻՓ⫼ǪȡȠǽǃ

ফֵ䱰ᆇȧᓩǢ䍋ǨǮǨǽǡǗȟȓǮǄ

পᡅ䂀ᯢ᳌ȀᕧǸǻℷǬǙপȟᡅǙȧǬǻϟǪǙǄ

Page is loading ...

Motorola LS1203 Quick Reference Manual

This manual is also suitable for

Motorola LS1203 Quick Reference Manual

in other languages

Related papers

Other documents