2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. Ergotron
  6. 98-017
98-017

Ergotron 98-017 Owner's manual

  • Hello! I've reviewed the user guide for the Ergotron Grommet Kit, which is designed to mount Ergotron LX arms to WorkFit sit-stand workstations. This document provides mounting instructions, safety warnings, and details on compatible LX arm models, like LX Desk Mount LCD Monitor Arm, LX Desk Dual Direct Arm, and LX Dual Side-by-Side Arm. I'm ready to answer your questions about the mounting process, weight limits, or any other aspect covered in the guide.
  • What is this kit for?
    What LX arms are compatible with this kit?
    What is the weight limit for LX Desk Mount LCD Monitor Arm mounted on WorkFit-T workstations?
    Is drilling required?
of
---W-revE•/
Grommet Kit
Mounts Ergotron LX Arms to the WorkFit-T, TL & TLE
Sit-Stand Desktop Workstations
www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
-/-
LXDeskMountLCDMonitorArm
-
LXDeskDualDirectArm
-/-
LXDualSide-by-SideArm
User's Guide
English
For the latest User Installation Guide please visit: www.ergotron.com
CAUTION!ThisKitisonlyforthefollowingErgotronLXArms
Mountingproductsotherthantheoneslistedwillcreateanunstablesituationandmayresult
inequipmentdamageand/orpersonalinjury
of
---W-revE•/
828-100
DO NOT place hands on or near support bars. Pinch points are
created during lifting and lowering the worksurface. Failure to
follow these instructions may result in serious personal injury.
WARNING
PINCH POINT
Safety
WarningBecausemountingsurfacematerialscanvarywidelyitisimperativethatyoumakesuremountingsurfaceisstrongenoughto
handlemountedproductandequipment
WarningImpactHazard!WorksurfaceundertensionMovingPartscanCrushandCut
RaiseworksurfacetotopofverticaladjustmentBEFOREremovingequipment
Failuretoheedthiswarningmayresultinseriouspersonalinjuryandorpropertydamage!
WarningImpactHazard!MovingPartscanCrushandCut
Raisethisproducttoitsfulluppositionbeforeli ingoff thedesk
Twopeoplearerequiredtoli thisproductoff thedesk
DonottipthisproductonitssideorupsidedownThisproductmustremainuprightatalltimes
Failuretoheedthiswarningmaycauseunintendedmotionoftheli mechanismresultinginpossible
seriouspersonalinjuryandorpropertydamage!
CAUTION! TIPPING HAZARD
Rotating display past FRONT or REAR edge may create an unstable situation and could result in equipment damage and/or personal injury.
CAUTION!FollowtheseinstructionswhendrillinganewgrommetholeFailuretofollowtheseinstructionsmaycausedamagetoequipment
orcreateandunstablesituationresultinginatippinghazardcausingpersonalinjuryorequipmentdamage
of
---W-revE•/
WORKFIT-TLTLE
10 - 40 lbs*
(4.5 - 18.2kg)
WORKFIT-T
10 - 35 lbs*
(4.5 - 15.88kg)
< 5 lbs
(2.27 kg)
AA
B
WorkFit-T: A+B= 10 - 35 lbs (4.5 - 15.88 kg)
WorkFit-TL, TLE: A+B= 10 - 40 lbs (4.5 - 18.2 kg)
-/-
LXDeskMount
LCDMonitorArm
-/-
LXDeskMount
LCDMonitorArm
-/-
LXDualSide-by-SideArm
-/-
LXDualSide-by-SideArm
-
LXDeskDualDirectArm
7.8 lbs
(3.6 kg)
14 lbs
(6.35 kg)
4.8 lbs
(2.18 kg)
4.8 lbs
(2.18 kg)
13.9 lbs
(6.3 kg)
6 lbs
(2.72 kg)
6 lbs
(2.72 kg)
-
LXDeskDualDirectArm
11.1 lbs
(5.03 kg)
Safety
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!
* Include the weight of the Arm(s) and monitor(s) when calculating total mounted weight.
New Maximum Arm Weight Capacity when mounted on the WorkFit-T, TL, TLE
of
---W-revE•/
ABC
1
2
3
x x
x
/-
/-x"
x
x
x
x
11mm
4mm
Ø/”
mm
WorkFit-T WorkFit-T
Components
ToolsNeeded
of
---W-revE•/
7
6
WorkFit-T WorkFit-T
-/-
LXDeskMountLCD
MonitorArm
-/-
LXDualSide-by-SideArm
-
LXDeskDual
DirectArm
UsecenterexistinggrommetholeDrillanewgrommetholeusing
thetemplate
CAUTION!Drillinganewgrommetholeis
onlywhenmountingthe-
LXDeskMountLCDMonitorArmDrilling
anewgrommetholeforanyotherproduct
willcreateanunstablesituationandmay
resultinequipementdamageand/or
personalinjury
DONOTuseanyotherholes
Li tofullupposition
of
---W-revE•/
Ø/”
mm
WorkFit-T WorkFit-T
WorkFit-T WorkFit-T
WorkFit-T WorkFit-T
WorkFit-TL WorkFit-TL
WorkFit-TLE WorkFit-TLE
-
LXDeskMount
LCDMonitorArm
-
LXDual
Side-by-SideArm
-
LXDeskDual
DirectArm
Drillanewgrommetholeusingthetemplate
Makesureyouusethecorrectsideofthetemplateforyourworksurface
-OnesideofthetemplateisfortheWorkFit-Twhichhasa"wideworksurface
-TheothersideofthetemplateisfortheWorkFit-TLandTLEwhicharewiderandhavea
"kgwideworksurface
Aligntheholesintemplatewiththefronttwoplugsintheworksurface
Makesureyouusethecorrectsideofthetemplateforyourworksurface
Drillyourgrommetholeanywherewithinthewhiteareaofthetemplate
DONOTdrillintheshadedareasofthetemplates
CAUTION!FollowtheseinstructionswhendrillinganewgrommetholeFailuretofollowthese
instructionsmaycausedamagetoequipmentorcreateandunstablesituationresultingina
tippinghazardcausingpersonalinjuryorequipmentdamage
of
---W-revE•/
4mm 4mm
/-x" /-x"
4mm 4mm
-/-
LXDeskMountLCD
MonitorArm
-/-
LXDualSide-by-SideArm
-
LXDeskDualDirectArm
SavescrewsforStep
ScrewsfromStep
of
---W-revE•/
11mm 11mm
/- /-
-/-
LXDualSide-by-SideArm
-/-
LXDeskMountLCD
MonitorArm
-
LXDeskDualDirectArm
© 2016 Ergotron, Inc. All rights reserved. WorkFit™ is a registered trademark of Ergotron, Inc.
www.ergotron.com |
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
Japan: [email protected]
CAUTION: Bolt must be centered in hole.
CAUTIONForsecurearma achmentandtoavoidequipmentdamage
platemustmakecontactwithundersideofdeskonbothsidesofthehole
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
/