SIMPLIFIED MFG EXARC User manual

Category
Video splitters
Type
User manual
1
EXARC
HDMI 2.0b (18Gbps) 40m
HDMI Extender with ARC and
Optical audio return
VER 2.1
2
Thank you for purchasing this product
The Simplified MFG EXARC is designed to provide years of reliable service. At Simplified MFG,
we want the experience with this device to be the best possible and are committed to helping
achieve that experience.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical spikes,
surges, electric shock, lighting strikes, etc. Use of surge protection systems is highly
recommended to protect and extend the life of your equipment. A HDSURGE is highly
recommended on cable and satellite boxes.
Table of Contents
1. Introduction .................................................................................................... 2
2. Features ........................................................................................................... 3
3. Package Contents ............................................................................................ 3
4. Specifications .................................................................................................. 4
5. Operation Controls and Functions ................................................................... 5
5.1 Transmitter Panel .................................................................................... 5
5.2 Receiver Panel ......................................................................................... 6
5.3 IR Pin Definition ...................................................................................... 6
6. Application Example ........................................................................................ 7
7. Warranty Information..……….……...………………………………………………… 8
8. Contact Information.……….……………………………………………………………… 8
1. Introduction
The EXARC can extend an HDMI2.0b (18Gbps) high-definition audio and video signal and
two-way IR up to 40 meters (132 feet) over a single Cat5e/6/7 cable, while simultaneously
transmitting ARC or optical S/PDIF signals from the RX back to the TX. The EXARC
supports resolutions up to 4K2K@60Hz 4:4:4, up to 18Gbps, and HDCP 2.2/1.4. In
addition, the EXARC extender is equipped with two-way IR and RS232 which allows for
source and display control.
The EXARC extender is a great way to bring audio back from the display to the TX end
either through the HDMI (ARC) or via optical S/PDIF. This transmission is independent of
the AV and control features.
3
2. Features
HDMI 2.0b and HDCP 2.2 compliant
Supports input and output video resolution up to 4k2k@60Hz 4:4:4 up
to 18Gbps
Supports HDR/HDR+/DolbyVision
Distance up to 131ft/40m @ 4k - 230ft/70m @1080p
Brings ARC or optical S/PDIF from RX back to TX
Outputs ARC audio through optical S/PDIF and/or HDMI
Two-way 12V IR transmission and RS232 pass through
Single power supply can be powered from either the RX or TX
3. Package Contents
1× HDMI 18Gbps transmitter
1× HDMI 18Gbps receiver
1× IR Blaster (1.5m length)
1× 20~60KHz IR Receiver (1.5m length)
1× 24V/1A Locking Power supply
2 x 3 Conductor Phoenix connectors
4× Mounting Ears
1× User Manual
4
4. Specifications
Technical
HDMI Compliance
HDMI 2.0b
HDCP Compliance
HDCP 2.2 / HDCP 1.4
Video Bandwidth
18Gbps
HDR Formats
HDR/HDR10+/DolbyVision
Video Resolution
Up to 4K60Hz 4:4:4
Color Space
RGB / YCbCr 4:4:4, YCbCr 4:2:2/4:2:0, YUV 4:4:4
Color Depth
8/10/12-bit (1080P60Hz, 4K30Hz, 4K60Hz YCbCr
4:2:2/4:2:0) 8-bit (4K60Hz 4:4:4)
HDMI Audio Formats
LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby
TrueHD, Dolby Digital Plus (DD+), DTS-ES, DTS
HD Master, DTS HD-HRA, DTS-X
ARC Audio Formats
Dolby Digital 5.1 and down, DTS 5.1, PCM 2.0
S/PDIF Audio Formats
Dolby Digital 5.1 and down, DTS 5.1, PCM 2.0
ESD Protection
Human body model ±8kV (Air-gap discharge) &±4kV (Contact
discharge)
Connections
Transmitter
Inputs: 1x HDMI Type A [19-pin female]
1 x IR in [3.5mm Stereo mini jack]
1x SERVICE [Micro USB, update port]
Outputs: 1x IR out [3.5mm stereo mini jack]
1 x Optical (S/PDIF) audio port
1x HDBaseT out [RJ45, 8-pin female]
Control: 1x 3 Conductor Phoenix connector
Receiver
Inputs: 1x HDBaseT in [RJ45, 8-pin female]
1x IR in [3.5mm Stereo mini jack]
1 x Optical (S/PDIF) audio port
1x SERVICE [Micro USB, Update port]
Outputs: 1x HDMI Type A [19-pin female]
1 x IR out [3.5mm Stereo mini jack]
Control: 1x 3 Conductor Phoenix connector
Mechanical
Housing
Metal Enclosure
Color
Black
Dimensions
Transmitter / Receiver:
140mm/5.5” [W] x 65mm/2.56 [D] x 18mm/.70 [H]
Weight
Transmitter: 235g/8.3oz., Receiver: 239g/8.43oz.
Power Supply
Input: AC 100 - 240V 50/60Hz Output: DC 24V/1A
Power Consumption
9.6W (Max)
Op. Temperature
32 - 104°F / 0 - 40°C
Storage Temperature
-4 - 140°F / -20 - 60°C
Relative Humidity
20 - 90% RH (no condensation)
5
5. Operation Controls and Functions
5.1 Transmitter Panel
Number
Name
Function description
1
HDMI In
HDMI input port, connect to HDMI source device such as
Media server or other 4K source
2
S/PDIF Out
Optical output from ARC or S/PDIF at RX
3
HDBaseT Out
Connect to HDBaseT In port on the receiving end with a
CAT6 cable.
4
Power LED
(Green)
The LED will illuminate when the transmitter is powered on.
5
Data signal
LED (Orange)
The LED will illuminate when the transmitter and the
receiver have signal transmission (link)
6
IR In
Connect to IR receiver (included). The IR signal is then sent
to the IR Out to the IR Blaster at the receiver.
7
IR Out
Connect to wideband IR Blaster (included). The IR signal is
from the IR In port of the receiver.
8
RS232
(3-PIN Phoenix)
Connect to third-party control system for 2-way RS232
communication with the RS232 connection at the RX
9
DC 24V
Plug DC 24V/1A power supply into the unit and connect the
adapter to an AC outlet.
(Note: The EXARC can be powered from either the RX or
the TX by 24V/1A power adapter, only one supply is needed)
EDID Switch is set to copy the display’s EDID. STD is a 1080p setting designed to help in
troubleshooting
6
5.2 Receiver Panel
❸ ❺
Name
Function description
HDMI Out
HDMI output port, connect to HDMI display device such as
TV or Projector with an HDMI cable.
S/PDIF In
Connect to optical output of display, the signal will output
at the S/PDIF on the TX
HDBaseT In
Connects to the TX HDBaseT output via category cable
Power LED (Green)
The LED will illuminate when the receiver is powered on.
It also indicates the connection from TX to RX
Data signal
LED (Orange)
The LED will illuminate when the transmitter and the
receiver have signal transmission (link).
IR In
Connect to wideband IR Receiver. The IR signal will be
transmitted to the IR Out port of the transmitter.
IR Out
The IR from the TX IR In will be transmitted through the
IR blaster connected here.
RS232
(3-PIN Phoenix)
Connect to third-party control system for 2-way RS232
communication with the RS232 connection at the RX
DC 24V
Plug DC 24V/1A power supply into the unit and connect
the adapter to an AC outlet.
(Note: The EXARC can be powered from either the RX or
the TX by 24V/1A power adapter, only one supply is
needed)
The audio selection switch is set to HDMI ARC, in this position, the audio from the eARC/ARC input
on the display will be output via HDMI in or optical out on the TX. In SPDIF IN position, the ARC
is disabled and the optical from the RX is sent to the TX instead of ARC.
7
5.3 IR PIN Definition
IR Use Example:
8
6. Application Example
Note that the optical S/PDIF on the RX will output the ARC or the S/PDIF from the display.
ARC audio has a higher bandwidth than optical however, CEC issues may necessitate the
use of the optical instead of the ARC. Also, ARC is backwards compatible with eARC. On
some displays, CEC may cause issues and ARC will not operate without CEC. Put the
display in eARC mode and this should solve the issue and pass ARC without CEC.
7. Warranty
Should you feel that this product does not function adequately due to defects in
materials or workmanship, we (referred to as “the warrantor”) will, for the length of
the period indicated below (starting from the original date of the purchase) either a)
repair the product with new or refurbished parts. Or b) Replace the product with new
or refurbished product. All Simplified MFG products are covered by a 3-year warranty.
During this period there will be no charge for unit repair, replacement of unit
components or replacement of the product if deemed necessary. The decision to
repair or replace is made by the warrantor. The purchaser must mail in the product
during the warranty period. This limited warranty only covers the product purchased
as new and is extended to the original purchaser only. It is non-transferrable to
subsequent owners, even during the warranty period. A purchase receipt or other
proof of purchase date is required for the limited warranty service.
9
8. Contact Information
Sales and Tech Support
P. 833-HDMI-411 (833-436-4411)
Simplified MFG • 550 W Baseline Rd Ste 102-121 • Mesa AZ 85210
© Copyright Simplified MFG 2023
Simplified MFG • 550 W Baseline Road Ste 102-121 Mesa, AZ 85210 www.simplifiedmfg.com 833-HDMI-411 (436-4411)
IR
Cat6/6A/7/8
IR
HDMI
The EXARC is a 40m HDMI 2.0b (18Gbp)/
70m 1080p HDR Extender that supports ARC
and return audio via optical S/PDIF.
ARC is output via HDMI port or optical
S/PDIF port on the TX unit
IR and RS232 commands are sent to and
from both the TX and the RX allowing IR and
RS232 to be sent from source end to display
and/or from display end to source end
IR
IR
RS232
ARC
Audio
042042
HDMI
ARC
Audio
RS232
Third Party
Control
Local device
Controlled
With RS232
Device
at rack
etc.
Optical out
works with
ARC as well
Optical
EXARC Quick Start Guide
At the TX end:
Is everything connected (Cat, HDMI, Power etc)?
Is the HDMI cable in the HDMI input of the TX? We often
use a loop out, make sure the input is not in this port.
What are the lights where the Cat cable plugs into doing?
Is the Green Lit Solid?
Yes, good! Flashing or off
the category cable is poor.
This can be the termination
(check the manual for wiring
termination), poor wire, or
interference from being run
poorly
Is the Amber Lit Solid?
Yes good! Flashing slowly
means no HDCP, off means
no signal at HDMI port(s)
How to use and trouble shoot
Simplified MFG Extenders
Typical Extender use
At the RX end:
Is the Green Lit Solid?
Yes, good! Flashing or off
the category cable is poor.
This can be the termination
(check the manual for wiring
termination), poor wire, or
interference from being run
poorly
Is the Amber Lit Solid?
Yes good! Flashing slowly
means no HDCP, off means
no signal at HDMI port(s)
Other Techniques:
Make the circuit simpler. Move the source near the
display or the display near the source and see if it
works with a short HDMI cable. You can use this to
verify the HDMI cables work as well. Add components
until the system fails.
Use a known working run of category cable across the
floor and see if behavior changes.
It is often the case that the displays setting can cause
odd/poor behavior. Consult the displays tech
resources. Also, it is possible we have seen the issue
and may have a tech paper on this.
Not a bad idea to keep the following on your service
vehicle:
Test source like an AppleTV or signal generator
Known working HDMI cables
Known working terminated Category cable
SP12S splitter for clocking issues, etc.
Simplified MFG • 550 W Baseline Road Ste 102-121 Mesa, AZ 85210 www.simplifiedmfg.com 833-HDMI-411 (436-4411)
EXARC
HDMI 2.0b (18Gbps) Extender
over Category cable with ARC
833-HDMI–411 (436-4411) • www.simplifiedmfg.com • 550 W Baseline Rd., Ste #102-121 Mesa, AZ 85210
Specifications:
The EXARC is a HDMI over category
cable extender that supports ARC
through the HDMI port or through the
optical S/PDIF port on the TX. It can
also be used as optical to optical.
The optical content is independent of
the AV going to the display. The
EXARC supports all versions of HDR,
WCG, and the entire HDMI 2.0b
(18Gbps) format. Other features in-
clude single ended power (either
end), Bi-Directional 12V IR, & RS232.
Distance at 4K is 50m (164ft.).
Features:
HDMI 2.0b (18Gbps)
HDR 8/10/10+ & Dolby Vision
Support
ARC through HDMI or S/PDIF
Single power supply (either end)
RS232
2-Way 12V IR (kit included)
50m (164ft) Transmission distance
Supports HBR (High Bit Rate
Audio)
3-Year Warranty
Technical
HDMI Compliance HDMI 2.0b
HDCP Compliance HDCP 2.2 and HDCP 1.4
Video Bandwidth 18 Gbps
Video Resolutions up to 4K2K@50/60Hz
(YUV4:4:4),4K2K@30Hz,1080P@120Hz, and 1080P
3D@60Hz
Color Space RGB, YCbCr 4:4:4, YCbCr 4:2:2
Color Depth 10-bit, 12-bit
HDMI Audio
Formats
LPCM 2/5.1/7.1CH, Dolby Digital, DTS 5.1, Dolby Digital+,
Dolby TrueHD, DTS-HD Master Audio, Dolby Atmos, DTS:X
ARC Audio
Formats Dolby Digital 5.1 and down, DTS 5.1, and PCM 2.0
S/PDIF Audio
Formats Dolby Digital 5.1 and down, DTS 5.1, and PCM 2.0
ESD Protection Human body model — ±8kV (air-gap discharge) & ±4kV
(contact discharge)
Connections
TX
Inputs: 1x HDMI Type A [19-pin female]
1x IR INPUT [3.5mm Stereo Mini-jack]
1x MICRO USB Service port
Outputs: 1x IR Out [3.5mm mini jack]
1x Optical (S/PDIF) audio port
1x HDBaseT out [RJ-45, 8-Pin Female]
Control: 1x 3-PIN Phoenix connector
RX
Inputs: 1x HDBaseT In [RJ-45, 8-Pin Female]
1x IR INPUT [3.5mm Stereo Mini-jack]
1x Optical (S/PDIF) audio port
1x MICRO USB Service port
Outputs: 1x HDMI Type A [19-pin female]
1x IR Out [3.5mm mini jack]
Control: 1x 3-PIN Phoenix connector
Mechanical
Housing Metal Enclosure
Color Black
Dimensions 140mm [5.5”] x 65mm [2.56”] x 18mm [0/7”]
Weight TX: 235g/8.3oz., RX: 239g/8.43oz.
Power Supply
Input: AC100 - 240V 50/60Hz
Output: DC 24V/1A (US/EU standards, CE/FCC/UL
certified)
Power
Consumption 18W (Max)
Operation
Temperature 32 - 104°F / 0 - 40°C
Storage
Temperature -4 - 140°F / -20 - 60°C
Relative
Humidity 20 - 90% RH (no condensation)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

SIMPLIFIED MFG EXARC User manual

Category
Video splitters
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI