ekwb EK-Scalar Quad 2-slot, EK-Scalar Dual 3-slot Installation guide

  • Hello! I've reviewed the instructions for the EK-Scalar terminals. This document details how to install the terminal, choose the correct inlet/outlet ports for your setup and provides compatibility information with EK-Vector GPU blocks. I can answer any questions you have about the installation process and features based on this document.
  • What is the purpose of the EK-Scalar terminal?
    What tools are needed to install the terminal?
    Do I need washers when installing the terminal?
    What size are the gaskets?
    What are the thread sizes for the ports?
INSTRUCTIONS
EK-Scalar
TERMINAL
Compatible with EK-Vector GPU blocks.
- 2 -
TABLE OF CONTENT
ATTACHING THE EK-SCALAR TERMINAL 3
CHOOSING INLET AND OUTLET PORTS 4
SUPPORT AND SERVICE 6
SOCIAL MEDIA 6
- 3 -
ATTACHING THE EK-SCALAR TERMINAL
Please take the following steps for installing any EK-Scalar terminal
to your graphics cards water blocks:
1. Remove the cover from your water block terminal, be careful not to
pull on any LED wiring as this may damage soldered joints.
2. Remove the pre-installed Terminal from each water block.
Unfasten the three (3) M4 screws using the supplied 2.5 mm Allen
(hex) key.
3. Install the gaskets (OR 15 x 1mm) in grooved slots on your new EK-
Scalar terminal. Make sure the gaskets are installed correctly! Each
water block or blank link requires two (2) gaskets!
4. Secure the new EK-Scalar Terminal to each water block using the
enclosed M4 x 20 DIN7984 screws with the suppliedd 2.5 mm
Allen (hex) key.
5. Plug all the remaining unused G1/4 threaded ports, if any, using
the 6mm Allen (hex) key and install your tubes fittings for both inlet
and outlet.
IMPORTANT: In case of using any of the Water Blocks from the list, make sure to use the M4 Washers under every M4 x 20 DIN7984 Screw
to secure the terminal.
EK-Quantum Vector XC3 RTX 3080/3090 D-RGB - Nickel + Plexi: https://www.ekwb.com/shop/ek-quantum-vector-xc3-rtx-3080-3090-d-rgb-nickel-plexi
EK-Quantum Vector XC3 RTX 3080/3090 D-RGB - Nickel + Acetal: https://www.ekwb.com/shop/ek-quantum-vector-xc3-rtx-3080-3090-d-rgb-nickel-acetal
EK-Quantum Vector Trinity RTX 3080/3090 D-RGB - Nickel + Plexi: https://www.ekwb.com/shop/ek-quantum-vector-trinity-rtx-3080-3090-d-rgb-nickel-plexi
EK-Quantum Vector Trinity RTX 3080/3090 D-RGB - Nickel + Acetal: https://www.ekwb.com/shop/ek-quantum-vector-trinity-rtx-3080-3090-d-rgb-nickel-acetal
EK-Quantum Vector RE RTX 3080/3090 D-RGB - Nickel + Plexi: https://www.ekwb.com/shop/ek-quantum-vector-re-rtx-3080-3090-d-rgb-nickel-plexi
EK-Quantum Vector RE RTX 3080/3090 D-RGB - Nickel + Acetal: https://www.ekwb.com/shop/ek-quantum-vector-re-rtx-3080-3090-d-rgb-nickel-acetal
EK-Quantum Vector RE RTX 3080/3090 - Full Nickel: https://www.ekwb.com/shop/ek-quantum-vector-re-rtx-3080-3090-full-nickel
EK-Scalar
Terminal
Screw M4 x 20 DIN 7984
OR 15 x 1 mm
- 4 -
CHOOSING INLET AND OUTLET PORTS
EK-Scalar terminals are intended to provide several different flow
configurations depending on the layout of your loop.
Although it may not be optimal for thermal performance it is also
possible to configure your EK-Scalar terminal in parallel with an
additional water block, such as a CPU block or monoblock. Ensure
that the flow rate of the loop is sufcient and each block has similar
restriction in order that each individual block receives adequate flow.
EK-Scalar Dual and Triple (parallel terminals)
- 5 -
No inlet
or outlet
possible
No inlet
or outlet
possible
No inlet
or outlet
possible
No inlet
or outlet
possible
EK-Scalar Quad (semi-parallel terminals)
For assistance please contact:
http://support.ekwb.com/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA
/