Chief WBM4E Installation guide

Brand: Chief

Model: WBM4E

Category: Flat panel accessories

Type: Installation guide

INSTALLATION INSTRUCTIONS

Interactive Flat Panel Over Whiteboard Mount

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

WBM4E

WBM4E Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

DEFINITIONS

MOUNTING SYSTEM: A MOUNTING SYSTEM is the

primary Chief product to which an accessory and/or component

is attached.

ACCESSORY: AN ACCESSORY is the secondary Chief

product which is attached to a primary Chief product, and may

have a component attached or setting on it.

COMPONENT: A COMPONENT is an audiovisual item

designed to be attached or resting on an accessory or mounting

system such as a video camera, CPU, screen, display,

projector, etc.

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all mounting systems

are properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this mounting system can result in serious personal injury

or damage to equipment! It is the installer’s responsibility to

make sure the structure to which this mounting system is

attached can support five times the combined weight of all

equipment. Reinforce the structure as required before

installing the mounting system. The wall to which the

mounting system is being attached may have a maximum

drywall thickness of 5/8” (1.6cm) on wood studs only.

Concrete walls may not have any drywall covering.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to mounting system does not

exceed 310 lbs (140.6 kg).

WARNING: Use this mounting system only for its intended

use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is

damaged. Return the mounting system to a service center for

examination and repair.

WARNING: Do not use this mounting system outdoors.

IMPORTANT ! :

The WBM4E is designed to be mounted to a:

•bare 8" thick solid concrete or 8" x 8" x 16" concrete

block wall; or

•2" x 4" wood stud (16" on center) wall covered with

drywall having a maximum thickness of 5/8".

--SAVE THESE INSTRUCTIONS--

Installation Instructions WBM4E

DIMENSIONS

DIMENSIONS: INCHES

[MILLIMETERS]

WBM4E Installation Instructions

TOOLS REQUIRED FOR INSTALLATION

PARTS

1/8" - wood stud

5/16" - concrete, brick

7/16"

1/2"

5/32"

(included)

7/16"

1/2"

A (4)

1/4”

B (4)

C (4)

1/4-20 x 2-1/2”

U (2)

[Upright W (3)

[Wall bracket cover]

Y (3)

[Sliding cover]

S (2)

1/16”

V (2)

[Adjustable leg]

G (4)

H (4)

J (4) FF (8)

#8 x 1/2"

CC (2)

1/4”

EE (2)

[AF6 Toggler]

BB (2)

1/4-20 x 2-1/2”

DD (2)

[Drywall anchor]

AA (2)

1/4-20 x 1 3/4”

Lag Bolt and Washer Kit WBM Hardware Kit

E (1)

5/32"

F (2)

1/4-20 x 3/8"

Hardware Kit with Tapping Screws

XL Display

Hardware

Kit A1 (4)

M6x12mm B1 (4)

M6x20mm C1 (4)

M6x25mm D1 (4)

M8x12mm

E1 (4)

M8x20mm F1 (4)

M8x30mm

G1 (8) H1 (4)

[Universal

washer]

K (2)

1/4-20 x 1/2" L (8)

1/4-20 x 5/8" M (2)

1/4-20"

N (10)

1/4" P (4)

[3" knob]

Q (4)

[Bumper]

R (8) T (6)

1-1/8"

AA (2)

1/4-20 x 1 3/4” BB (4)

1/4-20 x 2-1/2”

CC (2)

1/4”

DD (2)

[Drywall

anchor]

X (4)

[Bumper plate

retainer]

YY (2)

[Touch panel

cross bracket]

Z (2)

[Lower wall

bracket] ZZ (1)

[Wall assembly]

assembly]

[Not

used]

[Not

used]

[Not used]

[Optional]

[Spacer]

[Not used]

EE (10)

UX8 x 50R

[Not used]

[40mm knob]

[Not used]

Installation Instructions WBM4E

ASSEMBLY AND INSTALLATION

The WBM4E will allow an interactive flat panel display to be

installed over an existing chalkboard/whiteboard. The WBM4E

has telescoping legs which allows it to be anchored above and

below the existing chalkboard/whiteboard.

Assembling WBM4E Legs

1. Slide adjustable leg (V) up over bottom of upright assembly

(U). (See Figure 1)

2. Adjust leg (V) as necessary to set the correct length of entire

leg assembly. (See Figure 1)

IMPORTANT ! : Both adjustable legs MUST be fastened

through at least one hole in the upright assembly, not

only through mounting slots.

3. Fasten adjustable leg (V) in place using three knobs (R) and

three 1-1/8” spacers (T). (See Figure 1)

NOTE: Three knobs and spacers should be used on each leg

assembly.

4. Repeat Steps 1 through 3 on the other upright assembly (U).

Figure 1

Locate Mounting Site

WARNING: IMPROPER INSTALLATION CAN LEAD TO

MOUNT FALLING CAUSING SEVERE PERSONAL INJURY

OR DAMAGE TO EQUIPMENT! It is the installers

responsibility to make certain the structure to which the

mount is being attached is capable of supporting five times

the weight of the WBM4E and all attached equipment not to

exceed 310 lbs (140.6 kg).

WARNING: ELECTRICAL SHOCK, EXPLOSION AND

FIRE HAZARD! CUTTING OR DRILLING INTO

ELECTRICAL CORDS, CABLES OR GAS PLUMBING CAN

CAUSE DEATH OR SERIOUS PERSONAL INJURY!

ALWAYS make certain area behind mounting surface is free

of electrical wires, cables, gas, water, waste, or any other

plumbing before drilling or installing fasteners.

Adjusting Wall Brackets for Installation

NOTE: The two outside wall brackets on the wall assembly

may be adjusted to suit installation needs, but each

must be spaced a minimum of 16" from the center wall

bracket, AND the two outside wall brackets may only

be a maximum of 42" apart (outside bracket to outside

bracket).

NOTE: The center wall bracket must remain in the center of the

wall assembly (ZZ).

1. Slide outside wall brackets along wall assembly (ZZ), as

required, for the wall substrate. (See Figure 2)

2. Tighten button head cap screw on each wall bracket to

secure wall brackets to wall assembly. (See Figure 2)

Figure 2

NOTE: Proceed to the Installing to a Wood Stud Wall

section, or the Installing to a Concrete or Concrete

Block Wall section, as appropriate.

(U)

(V)

(U)

(V)

(R) x 3

(T) x 3

Fastened

through at

least one

hole in

upright

assembly

x 3

(side view)

(ZZ)

Wall brackets

WBM4E Installation Instructions

Installing to a Wood Stud Wall

1. Determine the center of the chalkboard/whiteboard.

2. Locate the closest 2" x 4" wood stud to the left and right of

the selected location.

NOTE: The two outside WBM4E wall brackets on the wall

assembly (ZZ) may be mounted a maximum of 42"

apart.

NOTE: The center wall bracket must remain in the center of the

wall assembly (ZZ) AND a minimum of 16" from both

outside wall brackets.

3. Using a level, mark the wall on each stud above existing

chalkboard/whiteboard through mounting holes in each

bracket on the wall assembly (ZZ). (See Figure 3)

4. Drill one 1/8” pilot hole at each mark. (See Figure 3)

5. Use six 1/4-20 x 2-1/2” lag bolts (BB or C) and six 1/4” flat

washers (A or CC) to attach wall assembly (ZZ) to wall. (See

Figure 3)

6. Proceed to Assembling Cross Brackets/Lower Brackets

section.

Figure 3

Installing to a Concrete or Concrete Block Wall

NOTE: The WBM4E may be attached to an 8" concrete wall or

an 8" x 8" x 16" concrete block wall.

1. Determine the center of the chalkboard/whiteboard.

NOTE: The two outside WBM4E wall brackets on the wall

assembly (ZZ) must be mounted a maximum of 42"

apart.

NOTE: The center wall bracket must remain in the center of the

wall assembly (ZZ) AND a minimum of 16" from both

outside wall brackets.

Using a level, mark the wall above existing chalkboard/

whiteboard through

mounting holes in each bracket on the

wall assembly (ZZ). (See Figure 4)

3. Drill one 5/16" x 2-3/4” pilot hole at each marking. (See

Figure 4)

Figure 4

4. Install an anchor (EE) into each pilot hole using a hammer.

(See Figure 4)

5. Use six 1/4-20 x 2-1/2” lag bolts (BB or C) and six 1/4” flat

washers (A or CC) to attach wall assembly (ZZ) to anchors

in wall. (See Figure 4)

Assembling Cross Brackets/Lower Brackets

1. Loosely assemble the cross brackets (YY) to the upright

legs using eight 1/4-20 x 5/8" button head cap screws (L)

and 1/4" washers (N) through the uprights and into either

the inner or outer set of mounting holes in the cross

brackets. (See Figure 5)

IMPORTANT ! : At least one cross bracket connection

point MUST be located through one hole in the upright

assembly, not only through mounting slots.

Figure 5

(A or CC) x 6

(ZZ)

(BB or C) x 6

(EE) x 6

(BB or C) x 6

(A or CC) x 6

(ZZ)

(L) x 8

(YY) x 2

(N) x 8

inner

hole

outer hole

Installation Instructions WBM4E

2. Attach one lower wall bracket (Z) to each of the leg

assemblies using one 1/4-20 x 1/2" flat head cap screw (K)

and one 1/4-20" hex nut (M) on each lower wall bracket.

(See Figure 6)

Figure 6

3. Hang uprights/cross brackets assembly on the wall

assembly (ZZ). (See Figure 7)

4. The mounting system may be laterally shifted by loosening

the button head cap screw on each wall bracket and moving

wall assembly within wall brackets, or by shifting the uprights

assembly laterally along the wall assembly (ZZ) to the desired

location. (See Figure 7)

5. Tighten any loosened button head cap screws on the wall

brackets to fasten the wall assembly in place.

NOTE: Additional lateral shift is available when using the inner

holes on cross brackets. (See Figure 5)

Figure 7

Attaching Interactive Flat Panel

1. Carefully place interactive flat panel face down on a soft,

non-abrasive surface.

2. Remove uprights/cross brackets assembly from wall

assembly and align mounting holes in upper cross bracket

with upper mounting holes in flat panel.

NOTE: If necessary, adjust the upper cross bracket so that

interactive flat panel will be at the desired height.

3. If necessary, loosen or remove hardware to slide the lower

cross bracket to align with the lower mounting holes in flat

panel.

WARNING: IMPROPER INSTALLATION CAN LEAD TO

DISPLAY FALLING CAUSING SERIOUS PERSONAL

INJURY OR DAMAGE TO EQUIPMENT! Using screws of

improper size may damage your display. Properly sized

screws will easily and completely thread into display

mounting holes. If spacers are required, be sure to use longer

screws of the same diameter.

4. Select correct screws, spacers (optional) and universal

washers (if required) from the XL display hardware kit (A1-

H1).

Figure 8

IMPORTANT ! : The M8 screws do NOT require a

washer. Use the universal washer (H1) only with M6

screws.

5. Attach flat panel to the uprights/cross brackets assembly

through the cross brackets using selected hardware. (See

Figure 8)

6. OPTIONAL: Loosen hardware and reposition the uprights

on the cross brackets if adjustment of the display height is

necessary.

(Z) x 2

(K) x 2(M) x 2

(ZZ)

NOTE: Use universal

x 4

(H1) x 4

NOTE: Example of

optional spacer (G1)

installation using the

(G1)

(H1)

washer (H1) ONLY with

M6 screws.

WBM4E Installation Instructions

Attaching Uprights Assembly to Wall Assembly

1. Move the slide nut to the outer most position on the wall

assembly (ZZ). (See Figure 9)

IMPORTANT ! : USE TWO PEOPLE FOR LIFTING! The

uprights/cross brackets assembly is heavy.

2. Hook flat panel with attached uprights assembly onto the

wall assembly (ZZ). (See Figure 9)

3. Move the slide nut behind the upright (U). (See Figure 9)

4. Fasten upright in place using one 1/4-20 x 3/8” button head

cap screw (F) and one 1/16” nylon spacer (S) [from WBM

Hardware kit] into slide nut. (See Figure 9)

5. Repeat for other side of wall assembly.

Figure 9

6. Attach two bumper plate retainers (X), 3" knobs (P), and

bumpers (Q) through each leg assembly, one just below top

of flat panel and one just above bottom of flat panel. (See

Figure 10)

7. Adjust 3" knobs (P) so that flat panel is supported evenly by

each of the four bumpers. (See Figure 10) Figure 10

(U)

(F)

(ZZ)

(S)

Slide nut

(Flat panel not shown)

(P) x 4

(X) x 4

(Q) x 4

Example of

an installed

bumper,

knob and

bumper

plate

retainer

Installation Instructions WBM4E

Adjustments

Micro Height Adjust and Leveling

1. The wall assembly (ZZ) can be adjusted or leveled by turning

the hex head bolt in the wall brackets. (See Figure 11)

•Turn clockwise to raise wall assembly

•Turn counterclockwise to lower wall assembly.

IMPORTANT ! : Height-adjust each side equally and in

small increments to prevent the wall assembly from

binding at the center wall bracket.

Figure 11

Completing Attachment to Wall

IMPORTANT ! : See Adjustments section to make any

necessary adjustments BEFORE completing attachment

to wall.

NOTE: The lower part of the WBM4E must be attached to the

wall using the correct hardware for the wall type. It may

be attached to a wood stud wall or to a concrete or

concrete block wall. Proceed to appropriate section for

instruction.

NOTE: If installing to a wood stud wall, drywall anchors (DD)

are required if the lower wall brackets do not align with

the wood studs.

Wood Stud Wall (if lower wall brackets are aligned with

studs)

1. Mark the wall over wood stud through the lower wall bracket

(Z) on each upright assembly. (See Figure 12)

2. Drill one 1/8” pilot hole at each mark. (See Figure 12)

3. Use two 1/4-20 x 2-1/2” lag bolts (BB or C) and two 1/4” flat

washer (A or CC) to attach each lower wall bracket (Z) to wall.

(See Figure 12)

Figure 12

Wood Stud Wall (if lower wall brackets are NOT aligned

with studs)

1. Mark the wall through the lower wall bracket (Z) on each

upright assembly. (See Figure 13)

2. Loosen and rotate the lower wall bracket to allow drilling of

the pilot hole.

3. Drill a 1/2” pilot hole at each marked location. (See Figure 13)

Figure 13

4. Rotate the lower wall bracket back into place.

5. Hold metal channel on drywall anchor (DD) flat alongside

plastic straps and slide channel through hole. (See Figure 14)

Figure 14

(ZZ)

LOWER

RAISE

(Flat panel not shown)

(BB or C) x 2

(V)

x 2

wood stud

(A or CC) x 2

wood studs

(Z)

(DD) x 2

Drywall

Plastic Straps

WBM4E Installation Instructions

6. Holding plastic straps on drywall anchor (DD), pull anchor

away from wall until channel rests flush behind wall. (See

Figure 15)

7. Slide plastic cap on anchor (DD) towards wall until flange of

cap is flush with wall. (See Figure 15)

Figure 15

8. Snap off plastic straps on anchor at wall by pushing side to

side, snapping off straps level with flange of plastic cap.

(See Figure 16)

9. Repeat Steps 5 through 8 for remaining mounting holes.

Figure 16

10. Use two 1/4-20 x 1 3/4” Phillips pan machine screws (AA)

and two 1/4” flat washers (A or CC) to attach

each lower wall

bracket (Z)

to anchors in wall. (See Figure 17)

Figure 17

Concrete or Concrete Block Wall

1. Mark the wall through the lower wall bracket (Z) on each

upright assembly (U). (See Figure 18)

Figure 18

2. Drill one 5/16” x 2-3/4” pilot hole at each marking. (See

Figure 18)

3. Loosen and rotate the lower wall bracket to allow installation

of the UX8 x 50R anchors (EE). (See Figure 18)

4. Install one anchor (EE) into each pilot hole using a hammer.

(See Figure 18)

5. Rotate the lower wall bracket back into place.

6. Use two 1/4-20 x 2-1/2” lag bolts (BB or C) and two 1/4” flat

washers (A or CC) to attach each lower wall bracket (Z) to

anchors in wall. (See Figure 18)

Plastic Cap

Drywall

Anchor Metal Channel

(Side View)

(DD) x 2

Plastic Straps

Drywall

Anchor Metal Channel

Plastic Cap

(Side View)

(AA) x 2

(A or CC) x 2

(Z)

(DD) x 2

(EE) x 2

(BB or C) x 2

(A or CC) x 2

(Z)

Installation Instructions WBM4E

Adding Covers

1. Open the lower flaps of the wall bracket cover (W) outward.

(See Figure 19)

2. Slide the cover downward, hooking the top of the wall

bracket covers (W) onto the tabs on top of wall assembly

brackets. (See Figure 19)

3. Slide the lower flaps of the wall bracket cover (L) under the

bottom of the wall assembly brackets (K). (See Figure 19)

Figure 19

4. Slide the sliding cover (Y) down over the wall bracket cover

(W) on both wall assembly brackets. (See Figure 20)

Figure 20

Wall

bracket

tab

(W)

(ZZ)

(Y)

(W)

(Y)

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344

P800.582.6480 / 952.225.6000

F877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, Netherlands

P+31 (0) 495 580 852

F+31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P852 2145 4099

F852 2145 4477

WBM4E Installation Instructions

Chief, a products division of

Milestone AV Technologies

8800-002860 Rev01

2016 Milestone AV Technologies

www.milestone.com

12/16

Chief WBM4E Installation guide

Brand: Chief

Model: WBM4E

Category: Flat panel accessories

Type: Installation guide

Download PDF

report

Chief WBM4E Installation guide

Chief WBM4E Installation guide

Related papers

Other documents