2. Computers & electronics
  3. Audio & home theatre
  4. Portable DVD/Blu-Ray players
  5. jWIN
  6. JD-VD755
JD-VD755

jWIN JD-VD755 Quick Start

  • Hello! I am an AI chatbot trained to assist you with the jWIN JD-VD755 Quick Start. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
- 1 -
Getting to Know Your Portable DVD Player
RIGHT SIDE DIAGRAM
REMOTE CONTROL DIAGRAM
Service life of battery
1. The battery normally lasts for about one year although this
depends on how often and for what operations the remote
control is used.
2. If the remote control unit fails to work even when it is
operated near the player, replace the battery.
3. Use a 3V lithium battery, No. CR2025.
BATTERY INSTALLATION FOR THE
REMOTE CONTROL
Insert the battery and match the (+) and (-) on battery to the
marks inside the battery compartment.
First-time use:
Remember to remove the insulating
Mylon piece from the battery.
1. SETUP button
2. INFO. button
3. PAUSE/UP button
4. MENU button
5. F.REV/LEFT button
6. PLAY/SEL. button
7. PREVIOUS button
8. STOP/DOWN button
9. Number buttons
10. MODE button
Portable DVD Player
Quick Guide
Welcome
to the Portable DVD Player Quick Guide.
Please carefully follow the instructions to set up your
Portable DVD Player.
FRONT VIEW DIAGRAM
1
2
3
4
5
6
7
8
18
17
16
15
14
13
12
11
10
9
19
+
+
CR2025
OPEN
PUSH
REMOTE CONTROL OPERATION RANGE
Point the remote control unit no more than 6 meters from the
remote control sensor and within 60
0
of the front of the unit.
The operating distance may vary according to the brightness of
the room.
Note:
1. Do not point bright lights at the remote control signal
sensor.
2. Do not place objects between the remote control unit and
the remote control signal sensor.
3. Do not use this remote control unit while simultaneously
operating the remote control unit of any other equipment.
LCD screen
SPEAKERS
SPEAKERS
PLAY button
PAUSE button
STOP button
POWER indicator
OPEN button
Remote Sensor
1. Volume Control
2. Headphone jack
3. Coaxial output jack
4. Audio output jack
5. Video output jack
6. POWER Switch
7. S-Video/P-Scan output jack
8. DC IN jack
12
3
45 6 87
Before using the battery pack, make sure to charge it.
You could choose to charge the battery pack directly or charge
it while attached to the portable DVD player.
30
remote sensor
11. LCD button
12. SUBTITLE button
13. TITLE button
14. ANGLE button
15. F.FWD/RIGHT button
16. AUDIO button
17. NEXT button
18. REPEAT 1/ALL button
19. MUTE button
Charge Time(hr) DVD Playback Time(hr)
NiMH 3800mAh
(6S1P)
Battery Pack Information (Charge & Playback Time)
3.5 2.7
Using the Battery Pack
“The shape of the following battery pack is only for reference; the actual shape
may differ.”
Battery release
button
Battery charge
indicator
DC IN jack
Battery
connectors
- 2 -
STEP 2. Connect it with earphones, or connect it
to external equipment. (B)
This unit can be connected to a television or home sound system.
Note: Before connections, make sure to turn off the power of the
portable DVD player and the external equipment.
STEP 3. Open the display panel. (C)
STEP 4. Slide the POWER switch to the ON position to
turn on the DVD player. (D)
STEP 5. Press <OPEN> to open the disc cover. (E)
STEP 6. Gently hold the edge of the disc, then put
it in the center with the printed side up.
STEP 7. Close the disc cover.
STEP 8. Press
<PLAY/SEL.> to play the disc.
(C)
(D)
(E)
Quick Operation Guide
STEP 1. Connecting to Power. (A)
Please connect the supplied AC adaptor to the DC IN jack on the
right side of the portable DVD 100Player.
(A)
A. To charge the battery pack directly
STEP 1. Connect the AC adapter (12V, 1.25A) to the DC IN
jack on the left side of the battery pack and a
household power outlet as shown in figure (A).
STEP 2. The battery charge indicator will turn red and start
charging.
STEP 3. When the battery pack is fully charged, the battery
charge indicator will turn green.
B. To charge the battery pack while
attached to the portable DVD player
STEP 1. Please align the portable DVD player’s battery
connectors with the battery pack’s battery
connectors. Attach the battery pack to the portable
DVD player as shown in figure (B).
Note:
1. Please turn the power off when attaching or removing the
battery pack.
2. If you want to remove the battery pack, press the battery
release button, then slowly remove it from the portable
DVD player.
STEP 2. Connect the AC adapter (12V, 1.25A) to the DC IN
jack on the right side of the portable DVD player
and a household power outlet.
STEP 3. The battery charge indicator will turn red and start
charging.
STEP 4. When the battery pack is fully charged, the battery
charge indicator will turn green.
Note:
1. The battery pack will not be charged while the portable DVD
player is turned on.
2. Please use the specific power adapter (12V, 1.25A) to charge
the battery pack.
(B)
Note: Make sure the external equipment supports the audio/
video input feature.
1 2 3
4
(White)(Red) (Yellow) (Blue) (Red) (Green)
Back/front panel of external equipment
P-Scan TV
Pb
Pr
Y
(Blue)
(Red)
(Green)
Video input
4
Audio input
(White)
L
R
(Red)
1
TV
Video input
2
S-Video
TV S-Video input
3
(B)
(A)
DC IN jack
/