Marantec EM 112 Owner's manual

Brand: Marantec

Model: EM 112

Type: Owner's manual

Marantec EM 112 expands the Control x.plus control unit, allowing you to connect signaling devices, control elements, and further modules. It offers various programmable functions such as relay outputs, door position monitoring, lighting control, and potential-free radio contact. The EM 112 enhances the functionality of your door system, enabling you to customize its operation and improve safety and convenience.

Expansion module EM 112

Manual for installation and operation

2 Manual for installation and operation, Expansion module EM 112 GB (#90253)

2. Table of contents

Caution!

Danger of personal injury!

The following safety advice must be

observed at all times so as to avoid

personal injury!

Attention!

Danger of material damage!

The following safety advice must be

observed at all times so as to avoid

material damage!

Advice / Tip

Check

Reference

Advice

1. Meaning of symbols . . . . . . . . . .2

2. Table of contents . . . . . . . . . . . .2

3. General safety advice . . . . . . . . .3

4. Product overview . . . . . . . . . . . .5

5. Installation . . . . . . . . . . . . . . . . .5

5.1 Install expansion module . . . . .5

5.2 Wiring of the expansion

module . . . . . . . . . . . . . . . . . .6

6. Programming . . . . . . . . . . . . . . .9

1. Meaning of symbols

Manual for installation and operation, Expansion module EM 112 GB (#90253) 3

3. General safety advice

Target group

This product may only be installed, connected and put into operation by qualified and trained professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working with electricity,

- with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction manual has to be observed.

Disregarding these warnings may lead to personal injury or material damage. If this advice is disregarded,

the manufacturer will not be liable for damages that might occur.

To avoid installation errors and damage to the device, it is imperative that the installation instructions are

followed. The product may only be operated after reading these installation and operating instructions.

The installation and operating instructions are to be given to the door system user, who must keep them

safe. They contain important advice for operation, checks and maintenance.

This item is produced according to the directives and standards mentioned in the Manufacturer's

Declaration and in the Declaration of Conformity. The product has left the factory in perfect condition with

regard to safety.

Power-operated windows, doors and gates must be checked by an expert (and this must be documented)

before they are put into operation and thereafter as required, but at least once a year.

Correct use

The expansion module expands the Control x.plus control unit.

Beside the advice in these instructions, please observe the general safety and accident

prevention regulations!

Our sales and supply terms and conditions are effective.

Please read carefully!

3. General safety advice

Installation tips

• Ensure that the devices to be connected (doors etc.) are in a mechanically faultless state.

• Before commencing cabling works it is very important to disconnect the system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout the cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be laid separately.

The operating voltage is 24 V.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

Please read carefully !

4 Manual for installation and operation, Expansion module EM 112 GB (#90253)

Manual for installation and operation, Expansion module EM 112 GB (#90253)) 5

5. Installation

Supply package

Dimensions

1 Expansion module

2 Cable harness for module connection

4. Product overview

4 / 1

4 / 2

126

5.1 Install expansion module

• Fit the expansion module (B) in the type 4 /

type 5 (A) expansion housing type.

5.1 / 1

6 Manual for installation and operation, Expansion module EM 112 GB (#90253)

Designation

Type / function

A Operating indicator

B Display for output XH19B

C Display for output XH19A

Display for control element

activated

XB59 Control element connections

XB41A

Connection of Control x.plus

control unit

XB41B Connection of further module

XH19A Connection of signalling device

XH19B Connection of signalling device

5.2 Wiring of the expansion

module

5. Installation

5.2.1 Overview of the module connections 5.2.2 Connection of the modules

XB41A

• Connect the Control x.plus control unit to the

connecting socket XB41A.

• Connect another module to socket XB41B as

required.

5.2.2 / 1

5.2.1 / 1

XB59

XB41A

XH19A

XH19B

XB41B

Connection of the control unit and a further

module

Manual for installation and operation, Expansion module EM 112 GB (#90253) 7

5. Installation

Reference:

The activated menus are described in

section 6.2.

-XB59

-SB8

13 14

-SB4

13 14

-SB47

13 14

-SB6

13 14

B5 8 4 47 6

5.2.2 / 2

Designation

Type / function

SB8 Operating button for IMPULSE*

SB4

Operating button

intermediate CLOSE position*

SB47 Master button CLOSE

SB6 Operating button for OPEN**

Connection of control element (XB59)

M08E002

* The function sequence is programmable in

level 8 / menu 6 of the Control x.plus control

unit.

** The function “active without stop” is not

modifiable through level 8 / menu 5.

-XH19A

-HH94

H1 92 94

Connection for signal light (XH19A)

Designation

Type / function

HH94 Signal light supplied by customer

XH19A Connection of signalling device

5.2.2 / 3

M08E002

Attention!

To avoid damage being caused to the

circuit board, the contact loading

(max. 230 V / 0.5 A) must be

observed.

Connection for signal light (XH19B)

-XH19B

-HH94

H1 92 94

5.2.2 / 4

M08E002

Designation

Type / function

HH94 Signal light supplied by customer

XH19B Connection of signalling device

5. Installation

8 Manual for installation and operation, Expansion module EM 112 GB (#90253)

6. Programming

An activated module results in the menus which follow in the Control x.plus control unit being activated.

Level 1 - Basic functions

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menü 5: Relay output (XH19A)

A5 B5 C5 D5 E5 F5 G5 H5 I5 J5 K5 L5 M5 N5 - -

Menü 6: Relay output (XH19B)

A6 B6 C6 D6 E6 F6 G6 H6 I6 J6 K6 L6 M6 N6 - -

Manual for installation and operation, Expansion module EM 112 GB (#90253) 9

6. Programming

Menu 5 + 6: Relay output (XH19A + XH19B)

Setting Function Explanation / Advice

A5/A6 Set with MDS - -

B5/B6 Signal light -

Level 3 /

Menu 7

C5/C6 Door position: OPEN - -

D5/D6 Door position: CLOSED - -

E5/E6 Intermediate OPEN position - -

F5/F6 Intermediate CLOSE position - -

G5/G6 Motor starts Wiping impulse 1 second -

H5/H6 Faults - -

I5/I6 Lighting Lighting duration

Level 5 /

Menu 4

J5/J6 Door in motion - -

K5/K6 Maintenance indicator - -

L5/L6 Door moves to OPEN - -

M5/M6 Door moves to CLOSED - -

N5/N6 Potential-free radio contact Wiping impulse 1 second

Level 4 /

Menu 8

Advice:

Further adjustment settings can be realised with the MDS diagnostic system.

10 Manual for installation and operation, Expansion module EM 112 GB (#90253)

6. Programming

Level 5 – Special function

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Menu 4: Lighting duration (in seconds)

OFF 5 10 15 20 25 30 35 40 50 80 100 120 150 180 255

Level 4 – Remote programming

Menu 8: Potential-free contact

LED 7 flashes slowly -> press the hand transmitter button -> LED 7 flashes quickly

Manual for installation and operation, Expansion module EM 112 GB (#90253) 11

English Copyright.

No part of this manual may be reproduced without our prior consent.

Subject to changes which are in the interest of technical improvements.

Version: 01.2011

#90253

1 - GB/KD 36-0308 - M - 0.5 - 0909

90253

Marantec EM 112 Owner's manual

Marantec EM 112 Owner's manual

Marantec EM 112 Owner's manual

Related papers

Other documents