Zanussi ZSLN1211 is a dishwasher designed for household use, offering efficient cleaning and drying performance. It features 5 programs tailored to different loads and soil levels, including an eco-friendly program for energy and water conservation. The dishwasher has a spacious interior with two baskets to accommodate various types of dishes, cutlery, and pots. It also includes a cutlery basket for safe and organized placement of utensils. Additionally, the Zanussi ZSLN1211 comes equipped with indicators for salt and rinse aid levels, ensuring optimal cleaning results.
Zanussi ZSLN1211 is a dishwasher designed for household use, offering efficient cleaning and drying performance. It features 5 programs tailored to different loads and soil levels, including an eco-friendly program for energy and water conservation. The dishwasher has a spacious interior with two baskets to accommodate various types of dishes, cutlery, and pots. It also includes a cutlery basket for safe and organized placement of utensils. Additionally, the Zanussi ZSLN1211 comes equipped with indicators for salt and rinse aid levels, ensuring optimal cleaning results.
GETTING
STARTED?
EASY.
User Manual
ZSLN1211
EN User Manual
Dishwasher
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
• Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
• Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
• Do not let children play with the appliance.
• Keep detergents away from children.
• Keep children and pets away from the appliance when the door
is open.
• Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
• This appliance is intended to be used in household and similar
applications such as:
– farm houses; staff kitchen areas in shops, offices and other
working environments;
– by clients in hotels, motels, bed & breakfast and other
residential type environments.
2
• Do not change the specification of this appliance.
• The operating water pressure (minimum and maximum) must be
between 0.5 (0.05) / 8 (0.8) bar (MPa)
• Follow the maximum number of 9 place settings.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
• Put the cutlery in the cutlery basket with the sharp ends
pointing down or put them in the cutlery drawer in a horizontal
position with the sharp edges down.
• Do not leave the appliance with the open door unattended to
avoid stepping accidentally onto it.
• Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to clean
the appliance.
• If the appliance has ventilation openings in the base, they must
not be covered e.g. by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
SAFETY INSTRUCTIONS
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not use the appliance before installing it in
the built-in structure due to safety manner.
• Follow the installation instructions supplied with
the appliance.
• Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
• Do not install or use the appliance where the
temperature is less than 0 °C.
• Install the appliance in a safe and suitable place
that meets installation requirements.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
• The appliance must be earthed.
• Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
3
• This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
• If the water inlet hose is damaged, immediately
close the water tap and disconnect the mains
plug from the mains socket. Contact the
Authorised Service Centre to replace the water
inlet hose.
USE
• Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
• Dishwasher detergents are dangerous. Follow
the safety instructions on the detergent
packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the appliance
until the programme is complete. Some
detergent may remain on the dishes.
• Do not store items or apply pressure on the
open door of the appliance.
• The appliance can release hot steam if you open
the door while a programme operates.
INTERNAL LIGHTING
WARNING! Risk of injury.
• Concerning the lamp(s) inside this product and
spare part lamps sold separately: These lamps
are intended to withstand extreme physical
conditions in household appliances, such as
temperature, vibration, humidity, or are intended
to signal information about the operational
status of the appliance. They are not intended to
be used in other applications and are not
suitable for household room illumination.
• To replace the internal lighting, contact the
Authorised Service Centre.
SERVICE
• To repair the appliance contact the Authorised
Service Centre. Use original spare parts only.
• Please note that self-repair or non-professional
repair can have safety consequences and might
void the guarantee.
• The following spare parts will be available for 7
years after the model has been discontinued:
motor, circulation and drain pump, heaters and
heating elements, including heat pumps, piping
and related equipment including hoses, valves,
filters and aquastops, structural and interior
parts related to door assemblies, printed circuit
boards, electronic displays, pressure switches,
thermostats and sensors, software and firmware
including reset software. Please note that some
of these spare parts are only available to
professional repairers, and that not all spare
parts are relevant for all models.
• The following spare parts will be available for 10
years after the model has been discontinued:
door hinge and seals, other seals, spray arms,
drain filters, interior racks and plastic peripherals
such as baskets and lids.
DISPOSAL
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and
pets to get closed in the appliance.
PRODUCT DESCRIPTION
The graphics below is just a general
product overview. For more detailed
information, refer to other chapters
and/or documents provided with the
appliance.
4
4
3
7
8
10 9
56
11
1
2
1
Upper spray arms
2
Lower spray arm
3
Filters
4
Rating plate
5
Salt container
6
Air vent
7
Rinse aid dispenser
8
Detergent dispenser
9
Cutlery basket
10
Lower basket
11
Upper basket
CONTROL PANEL
21
3
45
1
On/off button / Reset button
2
Programme indicators
3
Indicators
4
Programme button
5
Delay button
5
INDICATORS
Indicator Description
Drying phase indicator. It is on when you select a programme with the drying phase.
It flashes when the drying phase operates.
Salt indicator. It is on when the salt container needs refilling. It is always off while
the programme operates.
Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. It is always
off while the programme operates.
PROGRAMMES
The order of the programmes in the table may not
reflect their sequence on the control panel.
Programme Type of load Degree of soil Programme phases
1)
• Crockery
• Cutlery
• Pots
• Pans
• Normal
• Lightly dried-on
• Prewash
• Wash 50 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
• Crockery
• Cutlery
• Pots
• Pans
• Normal to heavy
• Dried-on
• Prewash
• Wash 60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AirDry
• Crockery
• Cutlery
• Pots
• Pans
• Normal
• Lightly dried-on
• Wash 60 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AirDry
• Crockery
• Cutlery
• Fresh • Wash 50 °C
• Intermediate rinse
• Final rinse 50 °C
• AirDry
2)
• All types of loads • All degrees of
soil
• Prewash
1) This is the longest programme offering the most efficient use of energy and water consumption for
crockery and cutlery with normal soil. This is the standard programme for test institutes. This programme is
used to assess compliance with the Ecodesign Comission Regulation (EU) 2019/2022.
2) This is a programme for rinsing off food remains from the dishes. It prevents odours forming in the appli-
ance. Do not use detergent with this programme.
6
CONSUMPTION VALUES
Programme
1)
2)
Water
(l)
Energy
(kWh)
Duration
(min)
9.9
3)
/ 9.9
4)
0.778
3)
/ 0.779
4)
240
3)
/ 240
4)
10.5 - 12.8 0.888 - 1.086 160
9.5 - 11.7 0.713 - 0.871 90
8.7 -10.6 0.542 - 0.663 30
2.9 - 3.6 0.012 - 0.015 15
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the
quantity of dishes can change the values.
2) The values for programmes other than ECO are indicative only.
3) In accordance with the 1016/2010 regulation.
4) In accordance with the 2019/2022 regulation.
Information for test institutes
To receive the necessary information for conducting
performance tests (e.g. according to EN60436),
send an email to:
In your request please include the product number
code (PNC) found on the rating plate.
For any other questions regarding your dishwasher
please refer to the service book provided with your
appliance.
SETTINGS
PROGRAMME SELECTION MODE AND
USER MODE
When the appliance is in programme selection
mode it is possible to set a programme and to enter
user mode.
Settings available in the user mode:
• The level of water softener according to the
water hardness.
• Activation or deactivation of the rinse aid empty
notification.
• The level of rinse aid according to the required
dosage.
• Activation or deactivation of the acoustic signal
for the end of a programme.
• Activation or deactivation of the AirDry.
As the appliance stores the saved settings,
there is no need to configure it before every
cycle.
How to set the programme selection mode
The appliance is in programme selection mode
when the programme indicator flashes.
After activation, the appliance is in programme
selection mode by default. If not, set the
programme selection mode the following way:
Press and hold the on/off button until the appliance
is in programme selection mode.
How to enter user mode
Make sure the appliance is in programme selection
mode.
To enter the user mode, press and hold the
programme button until the indicator
flashes and the indicators , , and are
on.
THE WATER SOFTENER
The water softener removes minerals from the water
supply, which would have a negative effect on the
washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in
equivalent scales.
7
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of
the water in your area. It is important to set the right
level of the water softener to assure good washing
results.
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol/l
Clarke de-
grees
Water softener level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
5
1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1
2)
1) Factory setting.
2) Do not use salt at this level.
Regardless of the type of detergent used, set
the proper water hardness level to keep the
salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard water.
Regeneration process
For the correct water softener operation, the resin
of the softener device needs to be regenerated
regularly. This process is automatic and is the part
of the normal dishwasher operation.
When the prescribed quantity of water (see values
in the table) has been used since the previous
regeneration process, a new regeneration process
will be initiated between the final rinse and the
programme end.
Water softener level Amount of water (l)
1 250
2 100
Water softener level Amount of water (l)
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
In case of the high water softener setting, it may
occur also in the middle of the programme, before
the rinse (twice during a programme). Regeneration
initiation has no impact on the cycle duration,
unless it occurs in the middle of a programme or at
the end of a programme with a short drying phase.
8
In that cases, the regeneration prolongs the total
duration of a programme by additional 5 minutes.
Subsequently, the rinsing of the water softener that
lasts 5 minutes may begin in the same cycle or at
the beginning of the next programme. This activity
increases the total water consumption of a
programme by additional 4 litres and the total
energy consumption of a programme by additional
2 Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible more than
one in the same cycle) may prolong the programme
duration by another 5 minutes when it occurs at any
point at the beginning or in the middle of a
programme.
All the consumption values mentioned
in this section are determined in
accordance with the currently
applicable standard in laboratory
conditions with water hardness
2.5mmol/L according to the
2019/2022 regulation (water softener:
level 3).
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
How to set the water softener level
Make sure the appliance is in user mode.
1. Wait until the indicator starts to flash, the
indicator continues to flash and the
remaining indicators are off.
The intermittent flashing of the indicator shows
the current setting: e.g. 5 flashes + pause + 5
flashes = level 5.
2. Press the programme button repeatedly to
change the setting. Each pressing of the
programme button increases the level number.
After reaching the level 10, the count starts
again from the level 1.
3. Press the on/off button to confirm the setting.
THE RINSE AID EMPTY NOTIFICATION
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically released
during the hot rinse phase.
When the rinse aid chamber is empty, the rinse aid
indicator is turned on notifying to refill rinse aid. If
the drying results are satisfactory while using multi-
tablets only, it is possible to deactivate the
notification for refilling rinse aid. However, for best
drying performance, always use rinse aid.
If standard detergent or multi-tablets without rinse
aid are used, activate the notification to keep the
rinse aid refill indicator active.
How to deactivate the rinse aid empty
notification
Make sure the appliance is in user mode.
1. Press the programme button immediately.
The indicator starts to flash.
2. Wait until the indicator continues to flash
and the remaining programme indicators are
off.
The indicator shows the current setting:
• is on = Rinse aid empty notification is
on.
• is off = Rinse aid empty notification is
off.
3. Press the programme button to change the
setting.
4. Press the on/off button to confirm the setting.
THE RINSE AID LEVEL
It is possible to set the released quantity of rinse
aid between level 1 (minimum quantity) and level 8
(maximum quantity). Level 0 deactivates the rinse
aid dispenser and no rinse aid is released. Factory
setting: level 5.
How to set the rinse aid level
Make sure the appliance is in user mode.
1. Press the programme button twice.
The indicator
starts to flash.
2. Wait until the indicator continues to flash
and the remaining programme indicators are
off.
The intermittent flashing of the indicator shows
the current setting: e.g. 5 flashes + pause + 5
flashes = level 5.
3. Press the programme button repeatedly to
change the setting. Each pressing of the
programme button increases the level number.
After reaching the level 8, the count starts
again from the level 0. The level 0 means that
the rinse aid dispensing is disabled.
4. Press the on/off button to confirm the setting.
ACOUSTIC SIGNALS
Acoustic signals sound when a malfunction of the
appliance occurs. It is not possible to deactivate
these acoustic signals.
There is also an acoustic signal that sounds when
the programme is completed. By default this
9
acoustic signal is deactivated but it is possible to
activate it.
How to activate the acoustic signal for the
end of the programme
Make sure the appliance is in user mode.
1. Press the programme button three times.
The indicator starts to flash.
2. Wait until the indicator continues to flash
and the remaining programme indicators are
off.
The indicator shows the current setting:
• is off = The acoustic signal is off.
• is on = The acoustic signal is on.
3. Press the programme button to change the
setting.
4. Press the on/off button to confirm the setting.
AIRDRY
AirDry improves the drying results with less energy
consumption.
During the drying phase, the door
opens automatically and remains ajar.
CAUTION! Do not try to close the
appliance door within 2 minutes after
automatic opening. This can cause
damage to the appliance.
AirDry is automatically activated with all
programmes excluding (if applicable).
CAUTION! If children have access to
the appliance, it is advised to
deactivate AirDry as opening the door
may pose a danger.
How to deactivate the AirDry
Make sure the appliance is in user mode.
1. Press the programme button four times.
The indicator starts to flash.
2. Wait until the indicator continues to flash
and the remaining programme indicators are
off.
The indicator shows the current setting:
• is off = AirDry is off.
• is on = AirDry is on.
3. Press the programme button to change the
setting.
4. Press the on/off button to confirm the setting.
BEFORE FIRST USE
1. Make sure that the current level of the
water softener agrees with the hardness
of the water supply. If not, adjust the level
of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any processing
residuals that can still be inside the appliance.
Do not use detergent and do not put dishes in
the baskets.
After starting the programme, the appliance
recharges the resin in the water softener for up to 5
minutes. The washing phase starts only after this
procedure is complete. The procedure is repeated
periodically.
THE SALT CONTAINER
CAUTION! Use rough salt designed
for dishwashers only. Fine salt
increases the risk of corrosion.
The salt is used to recharge the resin in the water
softener and to assure good washing results in
daily use.
HOW TO FILL THE SALT CONTAINER
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container (only for
the first time).
10
3. Fill the salt container with 1 kg of salt (until it is
full).
4. Carefully shake the funnel by its handle to get
the last granules inside.
5. Remove the salt around the opening of the salt
container.
6. Turn the cap of the salt container clockwise to
close the salt container.
CAUTION! Water and salt can come
out of the salt container when you fill
it. After you fill the salt container,
immediately start a programme to
prevent corrosion.
HOW TO FILL THE RINSE AID DISPENSER
B
C
A
CAUTION! Only use rinse aid
designed specifically for dishwashers.
1. Press the release element (A) to open the lid
(B).
2. Pour the rinse aid in the dispenser (C) until the
liquid reaches the marking "FILL".
3. Remove the spilled rinse aid with an absorbent
cloth to prevent excessive foam formation.
4. Close the lid. Make sure that the lid locks into
position.
DAILY USE
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
Make sure that the appliance is in programme
selection mode.
• If the salt indicator is on, fill the salt
container.
• If the rinse aid indicator is on, fill the rinse
aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for the
type of load and the degree of soil.
USING THE DETERGENT
B
C
A
11
CAUTION! Only use detergent
designed specifically for dishwashers.
1. Press the release button (B) to open the lid (C).
2. Put the detergent in the compartment (A). You
can use detergent in tablets, powder or gel.
3. If the programme has a prewash phase, put a
small quantity of detergent on the inner part of
the appliance door.
4. Close the lid. Make sure that the lid locks into
position.
SETTING AND STARTING A PROGRAMME
Starting a programme
1. Keep the appliance door ajar.
2. Press the on/off button to activate the
appliance. Make sure that the appliance is in
programme selection mode.
3. Press the programme button repeatedly until
the indicator of the programme you want to
select starts flashing.
4. Close the appliance door to start the
programme.
Starting a programme with delay start
1. Set a programme.
2. Press the delay button to delay the start of the
programme by 3 hours.
The indicator
is on.
3. Close the appliance door to start the
countdown.
During the countdown, it is not possible to change
the programme.
When the countdown is complete, the programme
starts.
Opening the door while the appliance
operates
Opening the door while a programme is running
stops the appliance. It may affect the energy
consumption and the programme duration. After
closing the door, the appliance continues from the
point of interruption.
If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by AirDry
function.
Do not try to close the appliance door
within 2 minutes after AirDry
automatically opens it as this may
cause damage to the appliance.
If, afterwards, the door is closed for at
least 3 minutes, the running
programme ends.
Cancelling the delay start
Press the on/off button for 3 seconds until the
appliance is in programme selection mode.
When you cancel the delay start, you have to set
the programme again.
Cancelling the programme
Press the on/off button for 3 seconds until the
appliance is in programme selection mode.
Make sure that there is detergent in the detergent
dispenser before you start a new programme.
The Auto Off function
This function decreases energy consumption by
deactivating automatically the appliance when it is
not operating.
The function comes into operation:
• When the programme is complete.
• After 5 minutes if a programme was not started.
End of the programme
When the programme is complete, the Auto Off
function switches the appliance off.
Close the water tap.
HINTS AND TIPS
GENERAL
Follow the hints below to ensure optimal cleaning
and drying results in daily use and to protect the
environment.
• Washing dishes in the dishwasher as instructed
in the user manual usually consumes less water
and energy than washing dishes by hand.
• Load the dishwasher to its full capacity to save
water and energy. For best cleaning results,
arrange items in the baskets as instructed in the
user manual and do not overload the baskets.
• Do not pre-rinse dishes by hand. It increases
the water and energy consumption. When
needed, select a programme with a prewash
phase.
• Remove larger residues of food from the dishes
and empty cups and glasses before putting
them inside the appliance.
12
• Soak or slightly scour cookware with firmly
cooked-on or baked-on food before washing it
in the appliance.
• Make sure that items in the baskets do not
touch or cover each other. Only then can the
water completely reach and wash the dishes.
• You can use dishwasher detergent, rinse aid
and salt separately or you can use the multi-
tablets (e.g. ''All in 1''). Follow the instructions
on the packaging.
• Select a programme according to the type of
load and the degree of soil. offers the
most efficient use of water and energy
consumption.
• To prevent limescale buildup inside the
appliance:
– Refill the salt container whenever
necessary.
– Use the recommended dosage of the
detergent and rinse aid.
– Make sure that the current level of the water
softener agrees with the hardness of the
water supply.
– Follow the instructions in the chapter "Care
and cleaning".
USING SALT, RINSE AID AND DETERGENT
• Only use salt, rinse aid and detergent designed
for dishwasher. Other products can cause
damage to the appliance.
• In areas with hard and very hard water, we
recommend to use basic dishwasher detergent
(powder, gel, tablets containing no additional
agents), rinse aid and salt separately for optimal
cleaning and drying results.
• Detergent tablets do not fully dissolve with short
programmes. To prevent detergent residues on
the tableware, we recommend that you use
tablets with long programmes.
• Always use the correct quantity of detergent.
Insufficient dosage of detergent can result in
poor cleaning results and hard-water filming or
spotting on the items. Using too much detergent
with soft or softened water results in detergent
residues on the dishes. Adjust the amount of
detergent based on the water hardness. Refer
to the instructions on the detergent packaging.
• Always use the correct quantity of rinse aid.
Insufficient dosage of rinse aid decreases the
drying results. Using too much rinse aid results
in bluish layers on the items.
• Make sure that the water softener level is
correct. If the level is too high, the increased
quantity of salt in the water might result in rust
on cutlery.
WHAT TO DO IF YOU WANT TO STOP USING
MULTI-TABLETS
Before you start to use separately detergent, salt
and rinse aid, complete the following steps:
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers
are full.
3. Start the shortest programme with a rinsing
phase. Do not add detergent and do put dishes
in the baskets.
4. When the programme is complete, adjust the
water softener according to the water hardness
in your area.
5. Adjust the released quantity of rinse aid.
6. Activate the rinse aid empty notification.
LOADING THE BASKETS
• Always use the whole space of the baskets.
• Use the appliance to wash dishwasher-safe
items only.
• Do not wash in the appliance items made of
wood, horn, aluminium, pewter and copper as
they could crack, warp, get discoloured or
pitted.
• Do not wash in the appliance items that can
absorb water (sponges, household cloths).
• Put hollow items (cups, glasses and pans) with
the opening facing downwards.
• Make sure that glasses do not touch each other.
• Put light items in the upper basket. Make sure
that the items do not move freely.
• Put cutlery and small items in the cutlery basket.
• Make sure that the spray arms can move freely
before you start a programme.
BEFORE STARTING A PROGRAMME
Before you start the selected programme, make
sure that:
• The filters are clean and correctly installed.
• The cap of the salt container is tight.
• The spray arms are not clogged.
• There is enough salt and rinse aid (unless you
use multi-tablets).
• The arrangement of the items in the baskets is
correct.
• The programme is suitable to the type of load
and the degree of soil.
• The correct quantity of detergent is used.
UNLOADING THE BASKETS
1. Let the tableware cool down before you
remove it from the appliance. Hot items can be
easily damaged.
2. First remove items from the lower basket, then
from the upper basket.
13
After the programme is completed,
water can still remain on the inside
surfaces of the appliance.
CARE AND CLEANING
WARNING! Before maintenance,
deactivate the appliance and
disconnect the mains plug from the
main socket.
Dirty filters and clogged spray arms
decrease the washing results. Make a
check regularly and, if necessary, clean
them.
CLEANING THE FILTERS
The filter system is made of 3 parts.
C
B
A
1. Turn the filter (B) counterclockwise and remove
it.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters.
5. Make sure that there are no residues of food or
soil in or around the edge of the sump.
6. Put back in place the flat filter (A). Make sure
that it is correctly positioned under the 2
guides.
14
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter (A). Turn it
clockwise until it locks.
CAUTION! An incorrect position of
the filters can cause bad washing
results and damage to the appliance.
CLEANING THE LOWER SPRAY ARM
We recommend to clean the lower spray arm
regularly to prevent soil from clogging the holes.
Clogged holes can cause unsatisfactory washing
results.
1. To remove the lower spray arm, pull it upwards.
2. Wash the spray arm under running water. Use
a thin pointed tool, e.g. a toothpick, to remove
particles of soil from the holes.
3. To install the spray arm back, press it
downwards.
CLEANING THE UPPER SPRAY ARMS
We recommend to clean the upper spray arms
regularly to prevent soil from clogging the holes.
Clogged holes can cause unsatisfactory washing
results.
The upper spray arms are placed under the upper
basket. The spray arms (B) are installed in the duct
(A) with the mounting elements (C).
A
B
C
1. Pull out the upper basket.
2. To detach the spray arm, turn the mounting
element clockwise.
15
3. Wash the spray arm under running water. Use
a thin pointed tool, e.g. a toothpick, to remove
particles of soil from the holes.
4. To install the spray arm back, insert the
mounting element in the spray arm and fix it in
the duct by turning it counterclockwise. Make
sure that the mounting element locks into
place.
EXTERNAL CLEANING
• Clean the appliance with a moist soft cloth.
• Only use neutral detergents.
• Do not use abrasive products, abrasive cleaning
pads or solvents.
INTERNAL CLEANING
• Carefully clean the appliance, including the
rubber gasket of the door, with a soft damp
cloth.
• To maintain the performance of your appliance,
use a cleaning product designed specifically for
dishwashers at least once a month. Carefully
follow the instructions on the packaging of the
product.
• Do not use abrasive products, abrasive cleaning
pads, sharp tools, strong chemicals, scourer or
solvents.
• Using short-duration programmes regularly can
cause grease and limescale buildup inside the
appliance. Run long-duration programmes at
least twice a month to prevent the buildup.
REMOVAL OF FOREIGN OBJECTS
Check the filters and the sump after each use of the
dishwasher. Foreign objects (e.g. pieces of glass,
plastic, bones or toothpicks, etc) decrease the
cleaning performance and can cause damage to
the drain pump.
1. Disassemble the filters system as instructed in
this chapter.
2. Remove any foreign objects by hand.
CAUTION! If unable to remove the
objects, contact an Authorised
Service Centre.
3. Reassemble the filters as instructed in this
chapter.
TROUBLESHOOTING
WARNING! Improper repair of the
appliance may pose a danger to the
safety of the user. Any repairs must be
performed by qualified personnel.
The majority of problems that can occur can
be solved without the need to contact an
Authorised Service Centre.
Refer to the below table for information on possible
problems.
16
With some problems, the dedicated indicator
flashes intermittently to indicate a malfunction and
the alarm code.
Problem and alarm code Possible cause and solution
You cannot activate the appliance. • Make sure that the mains plug is connected to the
mains socket.
• Make sure that there is no damaged fuse in the fuse
box.
The programme does not start. • Make sure that the appliance door is closed.
• If the delay start is set, cancel the setting or wait for
the end of the countdown.
• The appliance recharges the resin inside the water
softener. The duration of the procedure is approxi-
mately 5 minutes.
The appliance does not fill with water.
• The indicator flashes 1 time inter-
mittently.
• Acoustic signal sounds 1 time intermit-
tently.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is
not too low. For this information, contact your local
water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clog-
ged.
• Make sure that the inlet hose has no kinks or bends.
The appliance does not drain the water.
• The indicator flashes 2 times in-
termittently.
• Acoustic signal sounds 2 times inter-
mittently.
• Make sure that the sink spigot is not clogged.
• Make sure that the interior filter system is not clog-
ged.
• Make sure that the drain hose has no kinks or
bends.
The anti-flood device is on.
• The indicator flashes 3 times in-
termittently.
• Acoustic signal sounds 3 times inter-
mittently.
• Close the water tap.
• Make sure that the appliance is correctly installed.
• Make sure the baskets are loaded as instructed in
the user manual.
Malfunction of the water level detection
sensor.
• The indicator flashes 4 times in-
termittently.
• Acoustic signal sounds 4 times inter-
mittently.
• Make sure that the filters are clean.
• Switch the appliance off and on.
Malfunction of the wash pump or the drain
pump.
• The indicator flashes 5 times in-
termittently.
• Acoustic signal sounds 5 times inter-
mittently.
• Switch the appliance off and on.
17
Problem and alarm code Possible cause and solution
The temperature of the water inside the
appliance is too high or malfunction of the
temperature sensor occurred.
• The indicator flashes 6 times in-
termittently.
• Acoustic signal sounds 6 times inter-
mittently.
• Make sure that the temperature of the inlet water
does not exceed 60°C.
• Switch the appliance off and on.
Technical malfunction of the appliance.
• The indicator flashes 12 times in-
termittently.
• Acoustic signal sounds 12 times inter-
mittently.
• Switch the appliance off and on.
The level of water inside the appliance is
too high.
• The indicator flashes 15 times in-
termittently.
• Acoustic signal sounds 15 times inter-
mittently.
• Switch the appliance off and on.
• Make sure that the filters are clean.
• Make sure that the outlet hose is installed at the
right height above the floor. Refer to the installation
instructions.
The appliance stops and starts more
times during operation.
• It is normal. It provides optimal cleaning results and
energy savings.
The programme lasts too long. • If the delayed start option is set, cancel the delay
setting or wait for the end of the countdown.
Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the
adjustable feet (if applicable).
• The appliance door is not centred on the tub. Adjust
the rear foot (if applicable).
The appliance door is difficult to close. • The appliance is not levelled. Loosen or tighten the
adjustable feet (if applicable).
• Parts of the tableware are protruding from the bas-
kets.
Rattling/knocking sounds from inside the
appliance.
• The tableware is not properly arranged in the bas-
kets. Refer to basket loading leaflet.
• Make sure that the spray arms can rotate freely.
The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneous-
ly all the appliances in use. Check the socket am-
perage and the capacity of the meter or turn off one
of the appliances in use.
• Internal electrical fault of the appliance. Contact an
Authorised Service Centre.
Refer to "Before first use", "Daily
use", or "Hints and tips" for other
possible causes.
Once you have checked the appliance, deactivate
and activate the appliance. If the problem occurs
again, contact an Authorised Service Centre.
For alarm codes not described in the table, contact
an Authorised Service Centre.
18
WARNING! We do not recommend
using the appliance until the problem
has been completely fixed. Unplug the
appliance and do not plug it in again
until you are certain that it operates
correctly.
THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY
Problem Possible cause and solution
Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading
leaflet.
• Use more intensive washing programmes.
• Clean spray arm jets and filter. Refer to "Care and Clean-
ing".
Poor drying results. • Tableware has been left for too long inside a closed appli-
ance.
• There is no rinse aid or the dosage of rinse aid is not enough.
Set the rinse aid dispenser to a higher level.
• Plastic items may need to be towel dried.
• For the best drying performance activate AirDry.
• We recommend to always use rinse aid, even in combination
with multi-tablets.
There are whitish streaks or blu-
ish layers on glasses and dishes.
• The release quantity of rinse aid is too much. Adjust the rinse
aid level to a lower level.
• The quantity of detergent is too much.
There are stains and dry water
drops on glasses and dishes.
• The released quantity of rinse aid is not sufficient. Adjust the
rinse aid level to a higher level.
• The quality of the rinse aid can be the cause.
The dishes are wet. • For the best drying performance activate AirDry.
• The programme does not have a drying phase or has a drying
phase with low temperature.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the cause.
• The quality of the multi-tablets can be the cause. Try a differ-
ent brand or activate the rinse aid dispenser and use rinse
aid and multi-tablets together.
The interior of the appliance is
wet.
• This is not a defect of the appliance. it is caused by the hu-
midity in the air that condenses on the walls.
Unusual foam during washing. • Use the detergent for dishwashers only.
• There is a leak in the rinse aid dispenser. Contact an Author-
ised Service Centre.
Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to
"The water softener".
• Silver and stainless steel cutlery were placed together. Avoid
to put silver and stainless steel items close together.
19
Problem Possible cause and solution
There are residues of detergent
in the dispenser at the end of the
programme.
• The detergent tablet got stuck in the dispenser and therefore
was not completely washed away by water.
• Water cannot wash away the detergent from the dispenser.
Make sure that the spray arm is not blocked or clogged.
• Make sure that items in the baskets do not impede the lid of
the detergent dispenser from opening.
Odours inside the appliance. • Refer to "Internal cleaning".
Limescale deposits on the table-
ware, on the tub and on the in-
side of the door.
• The level of salt is low, check the refill indicator.
• The cap of the salt container is loose.
• Your tap water is hard. Refer to "The water softener".
• Even using multi-functional tabs use salt and set regeneration
of the water softener. Refer to "The water softener".
• If lime scale deposits still remain, clean the appliance with
appliance cleaners which are particularly suitable for this pur-
pose.
• Try different detergent.
• Contact the detergent manufacturer.
Dull, discoloured or chipped ta-
bleware.
• Make sure that only dishwasher-safe items are washed in the
appliance.
• Load and unload the basket carefully. Refer to basket loading
leaflet.
• Place delicate items in the upper basket.
Refer to "Before first use", "Daily
use" or "Hints and tips" for other
possible causes.
TECHNICAL INFORMATION
Dimensions Width / height / depth (mm) 446 / 818 - 898 / 550
Electrical connection
1) Voltage (V) 220 - 240
Frequency (Hz) 50
Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)
Water supply
Cold water or hot water
2) max 60 °C
Capacity Place settings 9
Power consumption Left-on mode (W) 5.0
Off-mode (W) 0.50
1) Refer to the rating plate for other values.
2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to
decrease energy consumption.
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Zanussi ZSLN1211 is a dishwasher designed for household use, offering efficient cleaning and drying performance. It features 5 programs tailored to different loads and soil levels, including an eco-friendly program for energy and water conservation. The dishwasher has a spacious interior with two baskets to accommodate various types of dishes, cutlery, and pots. It also includes a cutlery basket for safe and organized placement of utensils. Additionally, the Zanussi ZSLN1211 comes equipped with indicators for salt and rinse aid levels, ensuring optimal cleaning results.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
