H3C S3610 Series Operating instructions

Brand: H3C

Model: S3610 Series

Type: Operating instructions

This manual is also suitable for

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Table of Contents

Table of Contents

Chapter 1 SSL Configuration.......................................................................................................1-1

1.1 SSL Overview....................................................................................................................1-1

1.2 SSL Configuration Task List..............................................................................................1-2

1.3 Configuring an SSL Server Policy .....................................................................................1-2

1.3.1 Configuration Prerequisites.....................................................................................1-2

1.3.2 Configuration Procedure.........................................................................................1-2

1.3.3 SSL Server Policy Configuration Example..............................................................1-3

1.4 Configuring an SSL Client Policy.......................................................................................1-5

1.4.1 Configuration Prerequisites.....................................................................................1-5

1.4.2 Configuration Procedure.........................................................................................1-6

1.5 Displaying and Maintaining SSL........................................................................................1-6

1.6 Troubleshooting SSL .........................................................................................................1-6

1.6.1 SSL Handshake Failure..........................................................................................1-6

Chapter 2 HTTPS Configuration ..................................................................................................2-1

2.1 HTTPS Overview...............................................................................................................2-1

2.2 HTTPS Configuration Task List.........................................................................................2-1

2.3 Associating the HTTPS Service with an SSL Server Policy..............................................2-2

2.4 Enabling the HTTPS Service.............................................................................................2-2

2.5 Associating the HTTPS Service with a Certificate Attribute Access Control Policy..........2-3

2.6 Associating the HTTPS Service with an ACL....................................................................2-4

2.7 Displaying and Maintaining HTTPS...................................................................................2-4

2.8 HTTPS Configuration Example..........................................................................................2-5

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 1 SSL Configuration

1-1

Chapter 1 SSL Configuration

When configuring SSL, go to these sections for information you are interested in:

z SSL Overview

z SSL Configuration Task List

z Displaying and Maintaining SSL

z Troubleshooting SSL

1.1 SSL Overview

Secure Sockets Layer (SSL) is a security protocol providing secure connection service

for TCP-based application layer protocols, for example, HTTP protocol. It is widely

used in E-business and online bank fields to provide secure data transmission over the

Internet.

SSL provides these security services:

z Confidentiality: SSL encrypts data using a symmetric encryption algorithm and the

key generated during the handshake phase.

z Authentication: SSL supports authenticating both the server and the client through

certificates, with the authentication of the client being optional.

z Reliability: SSL uses key-based message authentication code (MAC) to verify

message integrity.

As shown in

Figure 1-1, the SSL protocol consists of two layers of protocols: the SSL

record protocol at the lower layer and the SSL handshake protocol, change cipher spec

protocol, and alert protocol at the upper layer.

Figure 1-1 SSL protocol stack

z SSL handshake protocol: Responsible for establishing a session between a client

and the server. A session consists of a set of parameters such as the session ID,

peer certificate, cipher suite (including key exchange algorithm, data encryption

algorithm and MAC algorithm), compression algorithm, and master key. An SSL

session can be used to establish multiple connections, reducing session

negotiation cost.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 1 SSL Configuration

1-2

z SSL change cipher spec protocol: Used for notification between a client and the

server that the subsequent packets are to be protected and transmitted based on

the newly negotiated cipher suite and key.

z SSL alert protocol: Allowing a client and the server to send alert messages to each

other. An alert message contains the alert severity level and a description.

z SSL record protocol: Fragmenting and compressing data to be transmitted,

calculating and adding MAC to the data, and encrypting the data before

transmitting it to the peer end.

1.2 SSL Configuration Task List

Different parameters are required on the SSL server and the SSL client.

Complete the following tasks to configure SSL:

Task Remarks

Configuring an SSL Server Policy Required

Configuring an SSL Client Policy Optional

1.3 Configuring an SSL Server Policy

An SSL server policy is a set of SSL parameters for a server to use when booting up. An

SSL server policy takes effect only after it is associated with an application layer

protocol, HTTP protocol, for example.

1.3.1 Configuration Prerequisites

Before configuring an SSL server policy, you must configure a PKI (public key

infrastructure) domain.

1.3.2 Configuration Procedure

Follow these steps to configure an SSL server policy:

To do... Use the command... Remarks

Enter system view

system-view

—

Create an SSL server

policy and enter its view

ssl server-policy

policy-name

Required

Specify a PKI domain for

the SSL server policy

pki-domain

domain-name

Required

By default, no PKI domain

is specified for an SSL

server policy.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 1 SSL Configuration

1-3

To do... Use the command... Remarks

Specify the cipher suite(s)

for the SSL server policy

to support

ciphersuite

[ rsa_aes_128_cbc_sha |

rsa_des_cbc_sha |

rsa_rc4_128_md5 |

rsa_rc4_128_sha ] *

Optional

By default, an SSL server

policy supports all cipher

suites.

Set the handshake

timeout time for the SSL

server

handshake timeout time

Optional

3,600 seconds by default

Configure the SSL

connection close mode

close-mode wait

Optional

Not wait by default

Set the maximum number

of cached sessions and

the caching timeout time

session { cachesize size

| timeout time } *

Optional

The defaults are as

follows:

500 for the maximum

number of cached

sessions,

3600 seconds for the

caching timeout time.

Enable certificate-based

SSL client authentication

client-verify enable

Optional

Not enabled by default

 Note:

If you enable client authentication here, you must request a local certificate for the

client.

1.3.3 SSL Server Policy Configuration Example

I. Network requirements

z A switch works as the HTTPS server.

z A host works as the client and accesses the HTTPS server through HTTP secured

with SSL.

z A certificate authentication (CA) issues a certificate to the switch.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 1 SSL Configuration

1-4

Caution:

In this instance, Windows Server works as the CA and the Simple Certificate

Enrollment Protocol (SCEP) plug-in is installed on the CA.

II. Network diagram

Figure 1-2 Network diagram for SSL server policy configuration

III. Configuration procedure

1) Request a certificate for the switch

# Create a PKI entity named en and configure it.

<Sysname> system-view

[Sysname] pki entity en

[Sysname-pki-entity-en] common-name http-server1

[Sysname-pki-entity-en] fqdn ssl.security.com

[Sysname-pki-entity-en] quit

# Create a PKI domain and configure it.

[Sysname] pki domain 1

[Sysname-pki-domain-1] ca identifier ca1

[Sysname-pki-domain-1] certificate request url

http://10.1.2.2/certsrv/mscep/mscep.dll

[Sysname-pki-domain-1] certificate request from ra

[Sysname-pki-domain-1] certificate request entity en

[Sysname-pki-domain-1] quit

# Create a local key pair through RSA.

[Sysname] public-key local create rsa

# Retrieve the CA certificate.

[Sysname] pki retrieval-certificate ca domain 1

# Request a local certificate.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 1 SSL Configuration

1-5

[Sysname] pki request-certificate domain 1

2) Configure an SSL server policy

# Create an SSL server policy named myssl.

[Sysname] ssl server-policy myssl

# Specify the PKI domain for the SSL server policy as 1.

[Sysname-ssl-server-policy-myssl] pki-domain 1

# Enable client authentication.

[Sysname-ssl-server-policy-myssl] client-verify enable

[Sysname-ssl-server-policy-myssl] quit

3) Associate HTTPS service with the SSL server policy and enable HTTPS service

# Configure HTTPS service to use SSL server policy myssl.

[Sysname] ip https ssl-server-policy myssl

# Enable HTTPS service.

[Sysname] ip https enable

4) Verify your configuration

Launch IE on the host and enter https://10.1.1.1 in the address bar. You should be able

to log in to the switch and manage it.

 Note:

z For details about PKI configuration commands, refer to PKI Commands.

z For details about the public-key local create rsa command, refer to SSH

Commands.

1.4 Configuring an SSL Client Policy

An SSL client policy is a set of SSL parameters for a client to use when connecting to

the server. An SSL client policy takes effect only after it is associated with an application

layer protocol.

1.4.1 Configuration Prerequisites

Before configuring an SSL client policy, you must configure a PKI domain. For details

about PKI domain configuration, refer to PKI Configuration.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 1 SSL Configuration

1-6

1.4.2 Configuration Procedure

Follow these steps to configure an SSL client policy:

To do... Use the command... Remarks

Enter system view

system-view

—

Create an SSL client

policy and enter its view

ssl client-policy

policy-name

Required

Specify a PKI domain for

the SSL client policy

pki-domain

domain-name

Required

No PKI domain is

configured by default.

Specify the preferred

cipher suite for the SSL

client policy

prefer-cipher

{ rsa_aes_128_cbc_sha

| rsa_des_cbc_sha |

rsa_rc4_128_md5 |

rsa_rc4_128_sha }

Optional

rsa_rc4_128_md5 by

default

Specify the SSL protocol

version for the SSL client

policy

version { ssl3.0 | tls1.0 }

Optional

TLS 1.0 by default

 Note:

If you enable client authentication on the server, you must request a local certificate for

the client.

1.5 Displaying and Maintaining SSL

To do... Use the command... Remarks

Display SSL server policy

information

display ssl server-policy

{ policy-name | all }

Display SSL client policy

information

display ssl client-policy

{ policy-name | all }

Available in any

view

1.6 Troubleshooting SSL

1.6.1 SSL Handshake Failure

I. Symptom

As the SSL server, the device fails to handshake with the SSL client.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 1 SSL Configuration

1-7

II. Analysis

SSL handshake failure may result from the following causes:

z No SSL server certificate exists, or the certificate is not trusted.

z The server is expected to authenticate the client, but the SSL client has no

certificate or the certificate is not trusted.

z The cipher suites used by the server and the client do not match.

III. Solution

1) You can issue the debugging ssl command and view the debugging information

to locate the problem:

z If the SSL server has no certificate, request one for it.

z If the server certificate cannot be trusted, install on the SSL client the root

certificate of the CA that issues the local certificate to the SSL server, or let the

server requests a certificate from the CA that the SSL client trusts.

z If the SSL server is configured to authenticate the client, but the certificate of the

SSL client does not exist or cannot be trusted, request and install a certificate for

the client.

2) You can use the display ssl server-policy command to view the cipher suite

used by the SSL server policy. If the cipher suite used by the SSL server does not

match that used by the client, use the ciphersuite command to modify the cipher

suite of the SSL server.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 2 HTTPS Configuration

2-1

Chapter 2 HTTPS Configuration

When configuring HTTPS, go to these sections for information you are interested in:

z HTTPS Overview

z HTTPS Configuration Task List

z Associating the HTTPS Service with an SSL Server Policy

z Enabling the HTTPS Service

z Associating the HTTPS Service with a Certificate Attribute Access Control Policy

z Associating the HTTPS Service with an ACL

z Displaying and Maintaining HTTPS

z HTTPS Configuration Example

2.1 HTTPS Overview

The HTTP Security (HTTPS) refers to the HTTP protocol that supports the Security

Socket Layer (SSL) protocol.

The SSL protocol of HTTPS enhances the security of the device in the following ways:

z Uses the SSL protocol to ensure the legal clients to access the device securely

and prohibit the illegal clients;

z Encrypts the data exchanged between the HTTPS client and the device to ensure

the data security and integrity, thus realizing the security management of the

device;

z Defines certificate attribute-based access control policy for the device to control

the access right of the client, in order to further avoid attacks from illegal clients.

 Note:

The total number of HTTP connections and HTTPS connections on a device cannot

exceed ten.

2.2 HTTPS Configuration Task List

Complete these tasks to configure HTTPS:

Configuration task Remarks

Associating the HTTPS Service with an SSL Server Policy Required

Enabling the HTTPS Service Required

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 2 HTTPS Configuration

2-2

Configuration task Remarks

Associating the HTTPS Service with a Certificate Attribute

Access Control Policy

Optional

Associating the HTTPS Service with an ACL Optional

2.3 Associating the HTTPS Service with an SSL Server Policy

You need to associate the HTTPS service with a created SSL server policy before

enabling the HTTPS service.

Follow these steps to associate the HTTPS service with an SSL server policy:

To do… Use the command… Remarks

Enter system view

system-view

—

Associate the HTTPS

service with an SSL

server policy

ip https

ssl-server-policy

policy-name

Required

Not associated by default

 Note:

z If the ip https ssl-server-policy command is executed repeatedly, the HTTPS

service is only associated with the last specified SSL server policy.

z When the HTTPS service is disabled, the association between the HTTPS service

and the SSL server is automatically removed. To enable it again, you need to

re-associate the HTTPS service with an SSL server policy.

z When the HTTPS service is enabled, no modification of its associated SSL server

policy takes effect.

2.4 Enabling the HTTPS Service

Before configuring the HTTPS, make sure that the HTTPS server is enabled.

Otherwise, other related configurations cannot take effect.

Follow these steps to enable the HTTPS service:

To do… Use the command… Remarks

Enter system view

system-view

—

Enable the HTTPS

service

ip https enable

Required

Disabled by default.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 2 HTTPS Configuration

2-3

 Note:

z After the HTTPS service is enabled, you can use the display ip https command to

view the state of the HTTPS service and verify the configuration.

z Enabling of the HTTPS service will trigger an SSL handshake negotiation process.

During the process, if the local certificate of the device already exists, the SSL

negotiation is successfully performed, and the HTTPS service can be started

normally. If no local certificate exists, a certificate application process will be

triggered by the SSL negotiation. Since the application process takes much time,

the SSL negotiation may fail and the HTTPS service cannot be started normally.

Therefore, the ip https enable command must be executed for multiple times to

ensure normal startup of the HTTPS service.

2.5 Associating the HTTPS Service with a Certificate

Attribute Access Control Policy

Associating the HTTPS service with a configured certificate access control policy helps

control the access right of the client, thus providing the device with enhanced security.

Follow these steps to associate the HTTPS service with a certificate attribute access

control policy:

To do… Use the command… Remarks

Enter system view

system-view

—

Associate the HTTPS

service with a certificate

attribute access control

policy

ip https certificate

access-control-policy

policy-name

Required

Not associated by default.

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 2 HTTPS Configuration

2-4

 Note:

z If the ip https certificate access-control-policy command is executed repeatedly,

the HTTPS server is only associated with the last specified certificate attribute

access control policy.

z If the HTTPS service is associated with a certificate attribute access control policy,

the client-verify enable command must be configured in the SSL server policy.

Otherwise, the client cannot log onto the device.

z If the HTTPS service is associated with a certificate attribute access control policy,

the latter must contain at least one permit rule. Otherwise, no HTTPS client can log

onto the device.

z For the configuration of an SSL server policy, refer to PKI Configuration.

2.6 Associating the HTTPS Service with an ACL

Associating the HTTPS service with an ACL can filter out requests from some clients to

let pass only clients that pass the ACL filtering.

Follow these steps to associate the HTTPS service with an ACL:

To do… Use the command… Remarks

Enter system view

system-view

—

Associate the HTTPS

service with an ACL

ip https acl acl-number

Required

Not associated by default.

 Note:

If the ip https acl command is executed repeatedly, the HTTPS service is only

associated with the last specified ACL.

2.7 Displaying and Maintaining HTTPS

To do… Use the command… Remarks

Display information about

HTTPS

display ip https

Available in any view

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 2 HTTPS Configuration

2-5

2.8 HTTPS Configuration Example

I. Network requirements

z Host acts as the HTTPS client and Switch acts as the HTTPS server.

z Host accesses Switch through Web to control Switch.

z CA (Certificate Authority) issues certificate to Switch. The common name of CA is

new-ca.

Caution:

In this configuration example, Windows Server serves as CA and you need to install

Simple Certificate Enrollment Protocol (SCEP) component.

II. Network diagram

Figure 2-1 Network diagram for HTTPS configuration

III. Configuration procedure

Perform the following configurations on Switch:

1) Apply for a certificate for Switch

# Configure a PKI entity.

<Switch> system-view

[Switch] pki entity en

[Switch-pki-entity-en] common-name http-server1

[Switch-pki-entity-en] fqdn ssl.security.com

[Switch-pki-entity-en] quit

# Configure a PKI domain.

[Switch] pki domain 1

[Switch-pki-domain-1] ca identifier ca1

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 2 HTTPS Configuration

2-6

[Switch-pki-domain-1] certificate request url

http://10.1.2.2:8080/certsrv/mscep/mscep.dll

[Switch-pki-domain-1] certificate request from ra

[Switch-pki-domain-1] certificate request entity en

[Switch-pki-domain-1] quit

# Generate a key pair locally by using the RSA algorithm.

[Switch] public-key local create rsa

# Obtain a server certificate from CA.

[Switch] pki retrieval-certificate ca domain 1

# Apply for a local certificate.

[Switch] pki request-certificate domain 1

2) Configure an SSL server policy associated with the HTTPS service

# Configure SSL server policy.

[Switch] ssl server-policy myssl

[Switch-ssl-server-policy-myssl] pki-domain 1

[Switch-ssl-server-policy-myssl] client-verify enable

[Switch-ssl-server-policy-myssl] quit

3) Configure certificate access control policy

# Configure certificate attribute group.

[Switch] pki certificate attribute-group mygroup1

[Switch-pki-cert-attribute-group-mygroup1] attribute 1 issuer-name dn ctn

new-ca

[Switch-pki-cert-attribute-group-mygroup1] quit

# Configure certificate access control policy myacp and create a control rule.

[Switch] pki certificate access-control-policy myacp

[Switch-pki-cert-acp-myacp] rule 1 permit mygroup1

[Switch-pki-cert-acp-myacp] quit

4) Reference an SSL server policy

# Associate the HTTPS service with the SSL server policy myssl.

[Switch] ip https ssl-server-policy myssl

5) Associate the HTTPS service with a certificate attribute access control policy

# Associate the HTTPS service with a certificate attribute access control policy myacp.

[Switch] ip https certificate access-control-policy myacp

6) Enable the HTTPS service

# Enable the HTTPS service.

[Switch] ip https enable

7) Verify the configuration

Operation Manual – SSL-HTTPS

H3C S3610&S5510 Series Ethernet Switches Chapter 2 HTTPS Configuration

2-7

Launch the IE explorer on Host, and enter https://10.1.1.1. You can log onto Switch and

control it.

 Note:

z For details of PKI commands, refer to PKI Commands.

z For details of the public-key local create rsa command, refer to SSH Commands.

H3C S3610 Series Operating instructions

Brand: H3C

Model: S3610 Series

Type: Operating instructions

This manual is also suitable for

Download PDF

report

H3C S3610 Series Operating instructions

This manual is also suitable for

H3C S3610 Series Operating instructions

Related papers

Other documents