ASSEMBLY AND OPERATION MANUAL
SHIPPING DAMAGE CLAIMS
When this equipment is shipped, title passes to the
purchaser upon receipt from the carrier. Consequently,
claims for the material damaged in shipment must be
made by the purchaser against the transportation
company at the time shipment is received.
BE SAFE
Your new Jack Stand was designed and built with
safety in mind. However, your overall safety can be
increased by proper training and thoughtful operation
on the part of the operator.
DO NOT operate or repair this equipment without
reading this manual and the important safety
instructions shown inside.
1645 Lemonwood Dr.
Santa Paula, CA. 93060, USA
Toll Free 1-800-253-2363
Tel: 1-805-933-9970
Fax: 1-805-933-9160
www.rangerproducts.com
PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO
INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT
YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF
THIS MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO
OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.
REV A 06-15-10
HEAVY DUTY JACK STANDS
MODELS:
RJS-3T
RJS-6T
Keep this operation manual near the
machine at all times. Make sure that
ALL USERS read this manual.
OPERATOR PROTECTIVE
EQUIPMENT
Personal protective equipment helps keep equipment use
safer. However, equipment does not take the place of safe
operating practices. Always wear durable work clothing.
Shop aprons or shop coats may also be worn, however
loose fitting clothing should be avoided. Tight fitting
leather gloves are recommended to protect operators.
Sturdy leather work shoes with steel toes and oil resistant
soles should be used by personnel to help prevent injury
in typical shop activities.
Eye protection is essential during installation and
operation. Safety glasses with side shields,
goggles, or face shields are acceptable.
Back belts provide support during lifting
activities and are also helpful in providing
operator protection. Consideration should
also be given to the use of hearing protection if activity
is performed in an enclosed area, or if noise levels are
high .
OWNER’S RESPONSIBILITY
To maintain machine and user safety, the responsibility of
the owner is to read and follow these instructions:
Follow all installation instructions.
Make sure installation conforms to all applicable
Local, State, and Federal Codes, Rules, and
Regulations; such as State and Federal OSHA
Regulations and Electrical Codes.
Carefully check the unit for correct initial function.
Read and follow the safety instructions. Keep them
readily available for machine operators.
Make certain all operators are properly trained, know
how to safely and correctly operate the unit, and are
properly supervised.
Allow unit operation only with all parts in place and
operating safely.
Carefully inspect the unit on a regular basis and
perform all maintenance as required.
Service and maintain the unit only with authorized or
approved replacement parts.
Keep all instructions permanently with the unit and
all decal’s on the unit clean and visible.
WARRANTY POLICY
Ranger Products™ are backed by over 35 years of manufacturing experience. Every Jack Stand bearing the Ranger™
name is sold with the following warranty.
Each Ranger Product™ is warranted to be free from defects in workmanship and material for a period of one •
year from the date of shipment provided that a written claim for such defect is made within that time.
This warranty does not cover damage or defects caused by carelessness of the operator, misuse, abuse or •
abnormal use which in any way impairs the proper functioning of the equipment or by the use or addition of
parts not manufactured by Ranger Products™ or its suppliers.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS OR A PARTICULAR PURPOSE.
If your Ranger Products™ machine is not functioning properly, call your Ranger Products™ dealer immediately. On
some occasions, an independent contractor may be hired to do the repairs. Within the warranty period, a customer
should not hire his own contractor unless it is authorized in writing by Ranger Products™.
If it is necessary to return equipment for repairs, your dealer will so advise you. When returning equipment for repairs,
see that machines are properly crated and protected, and prepay transportation.
Defective parts replaced at no charge must be returned to your dealer or Ranger Products™ within 60 days of the date
that the replacement parts are shipped; otherwise, you must pay for the replacement parts at the current selling price.
RJS-3T/ RJS-6T HEAVY DUTY JACK STANDS
2
ASSEMBLY INSTRUCTIONS
1. Remove both stands and ratcheting post from the box.
2. Insert post into the stands.
3. Bend in the tab on the side of collar using a punch and
hammer
4. Lift release lever and lift ratcheing bar to desired
height.
5. Check to make sure the dog engages each tooth
properly on the ratcheing post.
INSPECTIONS
Visual inspection should be made before each use
of the stand. Any stand which appears to be damaged in
any way is found to be badly worn, or operates abnormally
must be removed from service. If the stand is accidentally
subject to an abnormal load or shock, it must be inspected
by a manufacturer’s authorized repair facility immediately.
It is recommended that an annual inspection of the
stand be made by a manufacturer’s authorized repair
facility and any defective parts, decals, or warning labels
be replaced with manufacturer’s specifi ed parts. All repairs
must be made be a factory authorized service center.
A list of authorized repair facilities is available from the
manufacturer.
OPERATION
Begin by setting the parking brake on the vehicle and
blocking all wheels. Make sure the vehicle is raised to the
desired height and is stable. Extend the post to the height
close to the vehicles designated lift/ support member.
Check the load locking and release handle to ensure that
the dog portion has engaged a tooth on the post.
Make sure both jack stands are at equal height and
will support the load equally when the lifting device is
removed. Place jack stands carefully under the support
points specified by vehicle manufacturer.
DO NOT CRAWL UNDER AY VEHICLE
WHEN PLACING OR REMOVING STANDS.
SLOWLY lower the load onto the jack stands and
check to ensure the load is located on the center portion of
the post saddle. Check the load for stability. If the load is
NOT located on the center of the post saddle or if the load
is not stable, re-lift the load, reposition the jack stands to
ensure the proper loading before continuing with work or
repairs.
NOTE:
When using the jack stands for body shop work such as
frame straightening and/or body of vehicle, use caster
wheel type jack stand dollies to prevent load from being
pulled off jack stands.
WHEN REMOVING STANDS, carefully raise vehicle
enough to clear the stands, making sure the vehicle
remains stable. Remove stands, being careful not to crawl
under vehicle while doing so,. Carefully lower the vehicle
to the floor.
MAINTENANCE
Keep the jack stand clean and free of debris and dirt.
Oil release handle pivot points and ensure they
continue to work properly.
3
TECHNICAL SPECIFICATIONS
RJS-3T RJS-6T
Capacity 6,000 lbs / 2721 kg 12,000lbs. / 5,443 kg
Minimum Height 11” / 285mm 16” / 415mm
Maximum Height 16.85” / 428mm 24” / 610mm
Shipping Weight 14.5 lbs. / 6.6kg 25.4 lbs. /11.5kg
Shipping Dimensions 8.25” x 7.5” x 13.75”
210mm x 190mmx 350mm
11” x 9.8” x 16.9”
280mmx 250mm x 430mm
For Parts Or Service
Contact:
BendPak Inc. / Ranger Products
1645 Lemonwood Dr.
Santa Paula, CA. 93060
Tel: 1-805-933-9970
Toll Free: 1-800-253-2363
Fax: 1-805-933-9160
www.bendpak.com
www.rangerproducts.com
-
1
-
2
-
3
-
4
Ranger RJS-3T-RJS-6T Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ranger RFJ-10TL Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
BendPak RD-18G Owner's manual
-
-
Ranger Products RSC-2TF Operating instructions
-
-
-
-
-
-
-