Aiphone LE-SSV User manual

Category
Security cameras
Type
User manual
- INSTRUCTIONS -
The LE-SSV is a 2-gang stainless steel vandal proof and weather resistant sub station designed for use with the
systems listed above. It is constructed of 12 gauge stainless steel and has a stand alone color camera built in. The
unit either flush mounts into a 2-gang box, or surface mounts using the SBX-2G. Each unit includes a 12V DC power
transformer for the camera, tamper proof screws, and a tool for installation.
Vandal Resistant Sub Station with built in Color Pinhole Camera for use with
AP-M, LAF-C, LDF-C, LEF, LEM, MP-S Systems
Page 1
Transparent corner shadowing
on the picture is normal.
Front View Back View
The view achieved if the subject is 20" from the
camera is: 18" Vertically and 26½” Horizontally
Speaker
Camera
Call button
45cm
18”
67cm
26½”
50cm / 20”
50cm
20”
INSTALLATION:
1. For flush mounting, install sub station in standard 2-gang electrical box with minimum 2-1/2" depth.
2. For surface mounting, use the SBX-2G surface mount enclosure (sold separately).
3. Only the 12V DC power supply included should be used to power the LE-SSV camera.
4. IMPORTANT! These units are designed for use in normal weather conditions, and to allow drainage and
evaporation of moisture that naturally gets into the unit. Do not apply caulking or silicone sealant around the
unit when installing, and do not use weather stripping around the perimeter of the box when mounting. If
sealing the unit is required, the bottom must remain unsealed. Sealing the unit will prevent or inhibit moisture from
dissipating from inside the unit, which may cause corrosion or deterioration of the internal components over time.
1011
Page 2
WIRING DIAGRAMS:
1
E
2
E
~
10
E
AP-M Master
Red
Blk
Blu
Red
Blk
Blu
LE-SSV
1
(2)
(3)
E
+
-
MP-S Master
+
-
PS-1225UL
MP-S SYSTEM:
AP-M SYSTEM:
LE-SSV
Red
Blk
Blu
LE-SSV
Jumper Blue & Black
wires together
+
-
1
2
~
10
E
+
-
Red
Blk*
Blu
Red
Blk*
Blu
LEF, LAF/LDF
Master Station*
LE-SSV
PS-1225UL
* In a single master LEF system
only, 2 conductors homerun can
be used with the BLK and BLU
wires tied together and "E" and
"-" jumpered at the master.
LEF SYSTEM:
LE-SSV
+
-
1
E
+
-
Red
Blk
Blu
LEM Master LE-SSV
*LEM-1 or LEM-3: Use SKK-620 (6V DC)
LEM-1DL: Use PT-1210N
(or any source providing 12-16V AC or 12-24V DC)
Jumper Blue & Black
wires together
Power
Source*
LEM SYSTEM:
12V DC power input for camera
(Red - Must use supplied transformer)
Video output to monitor
or CCTV system (Yellow)
12V DC power input for camera
(Red - Must use supplied transformer)
Video output to monitor
or CCTV system (Yellow)
12V DC power input for camera
(Red - must use supplied transformer)
Video output to monitor
or CCTV system (Yellow)
12V DC power input for camera
(Red - must use supplied transformer)
Video output to monitor
or CCTV system (Yellow)
12V DC power input for camera
(Red - must use supplied transformer)
Video output to monitor
or CCTV system (Yellow)
12V DC power input for camera
(Red - Must use supplied transformer)
Video output to monitor
or CCTV system (Yellow)
Toll Free Technical Support:
1-800-692-0200
LE-SSV Instr.
1011JD
SPECIFICATIONS:
Audio Power Source: Supplied by master station
Speaker: 20 ohms, 4W, 2" diameter, water proof and puncture resistant, 2.4 oz. magnet
Call Button: SPST call button, momentary activation. Limited stop button
Call Annunciation: Call tone rings at master as long as button is held down. LED will remain lit for approx.
20 seconds (LEF, LEM-3, MP-3S, AP-5/10M only). Call tone only on LEM-1DL, LEM-1, and MP-1S.
Communication: Hands free at sub. Master is push-to-talk, release-to-listen.
CCTV Camera Output: 75 Ohm, 1Vp-p, NTSC, DC-coupled
Iris Control: Auto
Minimum Illumination: 1.0 lux
Camera image sensor: 1/3" CCD
Focal Length: 4.3mm Cone Pinhole Lens (78°)
Effective Pixels: 510(H) x 492(V) NTSC
Camera Power Source: 12V DC, 100mA (via included power supply)
MTBF: (Mean Time Before Failure) 80,000 Hours
Faceplate: 12 gauge stainless steel
Mounting: Flush mount into a 2-gang box (minimum 2-½” depth) or surface mount into SBX-2G (sold separately)
Tamper proof screws included (6x32 for use with flush 2-gang box) with T-10 TORX bit
When using SBX-2G, use the hardware included with that unit.
Terminations: Color-coded prewired pigtails. Red wire = “1"; Black wire = “E”; Blue wire = negative;
Red connector = 12VDC power; Yellow connector = 75 Ohm / 1Vp-p video output (BNC).
Operating Temperature: 14
F ~ 140°F (-10°C ~ 60°C)
Audio Wiring: 2 conductors in a 1-master LEF, MP-S, or AP-M system. 3 conductors in a multi-master LEF system.
Shielded cable is recommended. Use Aiphone #822202 for LEM or MP-S. Use #822202 or
#822203 for LEF. Use #832202 for AP-M systems.
Audio Wiring Distance: See system that unit is being used with for distance specifications.
Video Wiring: Independent BNC connection from substation pigtail to destination video device.
Dimensions (H x W x D): LE-SSV alone: 4-11/16" x 4-11/16" x 2"
With SBX-2G: 4-3/4" x 4-7/8" x 3-5/8" (Top) 2-3/8" (Bottom)
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
Color Camera
Call Button
Yellow BNC connector for
video output
Red: # terminal of Master
Black: E of Master
Blue: - (Neg.) of Master
Speaker
LE-SSV BACK VIEW:
Red connector for 12V DC camera
power input (from included power supply)
Power supply dimensions:
1-" W x 2-¼” H x 1-” D
6' DC cord.
NOTE: If using fiber optic interface, the video input on
the IFS VIC-5211 is not compatible with the LE-SSV
camera. The VIC-5211 can be used for audio only,
with a separate fiber module required for video.
Intercom wiring must be run at least 20" away from any AC wiring, fluorescent lighting, dimmer switches, or any
other electronic device that may cause interference.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Aiphone LE-SSV User manual

Category
Security cameras
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI