PRO-SERIES HTVANRK Owner's manual

Type
Owner's manual

This manual is also suitable for

READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
This manual provides important information on proper operation and maintenance. Every effort has been
made to ensure the accuracy of this manual. We reserve the right to change this product at any time without
prior notice.
STOP! DO NOT RETURN THIS PRODUCT TO THE RETAILER.
Questions? Problems? CONTACT CUSTOMER SERVICE
If you experience a problem or need parts for this product, visit our website http://www.buffalotools.com or
call our customer help line at 1-888-287-6981, Monday-Friday, 8 AM - 4 PM Central Time. A copy of the
sales receipt is required.
0912
HTVANRK
Multi-Use Van Rack
Assembly & Operating Instructions
Hardware Parts
A
C
D
E
Remarks
Hardware List
Description
A
Hex Bolt: 1/4" x 1 1/2"
Hex Bolt: 1/2" x 1 1/2"
B
SAE Flat Washer: 1/2"
C
Item No.
1
Hex Bolt
1/4" x 1 1/2"
B
Hex Bolt
1/2" x 1"
SAE Flat Washer
1/4"
SAE Flat Washer
1/2"
Allen Head
Set Screw
1/2" x 1/2"
SAE Flat Washer: 1/4"
D
Quantity
4
4
4
4
Allen Head Set Screw: 1/2" x 1/2"
E
Lock Washer: 1/2"
F
B
C
D
Lock Washer: 1/4"
G
2
4
4
Parts List
Description Quantity Remarks
1
Upright
4
2
Long Crossbrace
2
3
Short Crossbrace
2
Item No.
Note: A Wrench and an Allen Wrench (not included) are tools required for installation.
HTVANRK Multi-Use Van Rack
2
Multi-Use Van Rack HTVANRK Assembly and Operating Instructions
Verify that you have received the hardware and parts in the correct quantities as shown below.
F
Lock Washer
1/2"
G
Lock Washer
1/4"
2
3
HTVANRK Adjusts From 56” to 77” Wide, and adjusts From 6 1/4” to 8 1/2” High
Step 2
Place the completed crossbraces on top of the van and adjust for
proper width. Proceed to tighten the Set Screw (E). Adjust the
Gutter Clamp around the van’s rain gutter (FIG 4) and tighten
with Bolt (A), Lock Washers (G) and Flat Washers (D).
The Multi-Use Van Rack is now ready for use.
Note: Move the crossbrace to eliminate wind noise.
HTVANRK Multi-Use Van Rack
3
A
G
D
B
Mounting Holes
FIG 1
F
C
2
3
E
WARNING: DO NOT EXCEED 500 LB. LOAD CAPACITY.
FIG 3
FIG 2
Gutter Clamp
Rain Gutter
Gutter Clamp
FIG 4
Short & Long Crossbraces
Van Roof
Step 1
Select the Upright Mounting Hole that matches the roof top of the van. (FIG 1)
Insert Hex Bolt (B), Lock Washer (F), & SAE Flat Washer (C) into Mounting Hole and thread through
the Short Crossbrace (FIG 2). Insert the Short Crossbrace into the Long Crossbrace (FIG 3). Insert
the Set Screw (E) but don’t tighten. Add the remaining Upright to complete the first crossbrace.
Repeat Step 1 to complete the second and final crossbrace.
  • Page 1 1
  • Page 2 2
  • Page 3 3

PRO-SERIES HTVANRK Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI