Candy CDPM 77883X User manual

Page is loading ...

Congratulations!

Thank you for choosing a Candy

appliance; quality dishwashers which

guarantee high performance and

reliability.

Candy manufacture a vast range

of domestic appliances: washing

machines, washer/dryers, cookers,

microwave ovens, ovens and hobs,

refrigerators and freezers.

Ask your dealer for the catalogue with

the complete range of Candy products.

Please read this booklet carefully as

it provides important information

regarding the safe installation, use,

and maintenance of the machine,

together with some useful advice on

how to achieve the best results from

your dishwasher.

For future reference please keep this

instruction booklet in a safe place.

CUSTOMER SERVICE AND

GUARANTEE

Your new appliance is fully guaranteed

by the manufacturer for 12 months

against electrical/mechanical break-

down excluding:

A. Any faults which occur due to bad

installation or misuse of the machine.

B. Any faults which occur due to repair

of, or interference with, the machine

by any person not authorised by the

manufacturer to carry out service.

C. Any faults which occur due to

any parts which are fitted to the

machine which are not the original

manufacturers parts.

D. Any faults arising from non-domestic

use or unusual or abnormal use of

the machine.

E. Any faults arising from operation at

incorrect voltage.

F. Any faults arising from incorrect

operation of the machine.

The guarantee applies to Gt Britain

and Northern Ireland only, and is an

addition to your statutory rights.

AFTER SALES SERVICE

For service and repairs call your local engineer on our national telephone number:

GIAS Service Tel: 08444 995599

Support Service (Eire 0818 200021)

12

13

DESCRIPTION OF THE CONTROL PANEL

A "ON/OFF" button

B "PROGRAMME SELECTION" button

C "DELAY START" button

D "EXPRESS" option button

E "ALL IN 1" option button

F "START"/"RESET" button

(start/cancelling programme)

G "OPTION SELECTION" lights

H DIGITAL DISPLAY

I

Programme guide

DIMENSIONS

TECHNICAL DATA

CONSUMPTION (main programmes)*

Programme Energy (kWh) Water (L)

HYGIENIC

UNIVERSAL

ECO

ULTRA RAPID 24'

Width x Height x Depth (cm) 60 x 85 x 60

Depth with door open (cm) 120

EN 50242 place load

Capacity with pans and dishes

Water supply pressure (MPa)

Fuse / Power input / Supply voltage

16

9 persons

Min. 0,08 - Max. 0,8

See rating plate

Power consumption of the off-mode and of the left-on mode: 0,30 W / 0,45 W

*Values are measured in a laboratory according to European Standard EN 50242 (consumption may

vary according to conditions of usage).

59,8 x 82 x 57,3

117

With working top Without working top

2,07

1,46

0,95

0,59

21

15

10

9

14

PROGRAMME SELECTION

AND SPECIAL FUNCTIONS

(Use in conjunction with programme guide)

Programme settings

■ Open the door and place the dirty dishes

inside the appliance.

■ Press the "ON/OFF" button for about 2

seconds. The display will show two lines.

■ Choose a programme by pressing the

"PROGRAMME SELECTION" button.

■ If you wish to select an option, press the

corresponding button (the indicator light

will turn on).

The option buttons can be selected or

deselected WHITIN one minute of the

programme commencing.

■ Press the "START" button.

The length of the program will be shown on

the display alternating hours with

minutes [I.e: 1 h (1 hour) / 25 (25 minutes)].

■ When the door is shut, after an audible

signal has sounded, the programme will

start automatically. The display will show

the time remaining to the end of the cycle.

WITHIN one minute of the programme

commencing, another programme

can be selected, simply by pressing

the "PROGRAMME SELECTION"

button.

"IMPULSE" programmes

The “IMPULSE” programmes use an

impluse washing technology, which reduces

consumption, noise and increases

performances.

IMPORTANT

The “intermittent” working of the

washing pump MUST NOT BE

considered a malfunction, it is a

characteristic of the impulse washing

so must be considered a normal

function of the programme.

Programme interruption

Opening the door when a programme is

running is not recommended especially during

the main wash and final hot rinse phases.

However, if the door is opened while a

programme is running (for example, to add

dishes) the machine stops automatically and

the display will flash the remaining time

before the end of the cycle. Close the door,

without pressing any buttons. The cycle will

start from where it left off.

IMPORTANT

A running program can be interrupted

without opening the door by

pressing the "ON/OFF" button. In

this case, simply press the "ON/OFF"

button again to restart the cycle from

where it left off.

WARNING!

If you open the door during the

drying cycle, an audible audio signal

advises you that the drying cycle has

not yet finished.

Option buttons

"EXPRESS" button

This button provides an energy and time

saving of 25% on average (according to

the select cycle) reducing the wash water

temperature and the drying time during the

final rinse.

This programme is recommended for light

soil washes, and for slightly wet dishes that

are not fully dry, & improved drying results.

We advise you to leave the door of the

Dishwasher half-open at the end of the

cycle, to allow for a natural circulation of air

inside the dishwasher.

"ALL IN 1" button

This option optimises the use of "ALL in 1"

("3 in 1"/"4 in 1"/"5 in 1", ecc.) combined

detergents.

By pressing this button, the selected

washing programme is modified to get best

performance from combined detergents

(furthermore, the salt empty alert will be

de-activated).

WARNING!

Once selected, this option keeps

being on (light on) also for next

washing cycles and it can be de-activate

(light off) only by pressing the button

once again.

IMPORTANT

This option is recommended when

using the ULTRA RAPID 24' program,

the duration of which will be

extended for about 15 minutes,

allowing the detergent tablets to

achieve a better performance.

Salt empty alert

If your dishwasher requires filling with salt,

the display will show and flash "SL" when

the dishwasher is switched on.

The appearance of white stains on dishes

is generally a warning sign that the salt

container needs filling.

15

Changing a running programme

Proceed as follows to change or cancel a

running program:

■ Hold the "RESET" button down for at

least 3 seconds. "00" will appear on the

display and some audible signals will

sound.

■ The running programme will be cancelled.

The display will show two lines.

■ At this point a new programme can be set.

WARNING!

Before starting a new programme,

you should check that there is still

detergent in the dispenser.

If necessary, top up the dispenser.

Programme operations

Whilst a programme is running, the display

shows the time remaining to the end of the

cycle, which is automatically updated.

If there is any break in the power supply

while the dishwasher is operating, a

special memory stores the selected

programme and, when the power is

restored, it continues where it left off.

Programme end

A 5 second alarm will sound (if not muted)

3 times at 30 second intervals to signal that

the programme has ended.

The dishwasher will automatically switch

off.

16

"DELAY START" button

Dishwasher start time can be set with this

button, delaying start from 1 to 23 hours.

Proceed as follows to set a delayed start:

■ Press the "DELAY START" button ("00"

will appear on the display).

■ Press the button again to increase the

delay in hours (each time the button is

pressed the delay is increased by 1 hour

to a maximum of 23).

■ To start the countdown, press the

"START" button.

The display will show the time remaining

to the begin of the programme.

At the end of the countdown, the programme

will automatically start and the length of the

selected cycle will be shown in the display.

Proceed as follows to cancel a delayed

start:

■ Hold the "RESET" button down for at

least 3 seconds. "00" will appear on the

display and some audible signals will

sound.

■ The delayed start and the selected

programme will be cancelled.

The display will show two lines.

■ At this point, a new programme and

option buttons must be set to start a

new programme as indicated in the

"PROGRAMME SETTINGS" section.

Alarm mute for the PROGRAMME

END

The alarm for the programme end may be

muted as follows:

IMPORTANT

The dishwasher must ALWAYS be off

before start of this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 15 seconds

(during this time 2 audible signals will

sound).

3. Release the button when the second

audible signal sounds ("b1" will appear

on the display to indicate that the alarm

is on).

4. Press the same button again ("b0" will

appear on the display to indicate that the

alarm is off).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To turn the alarm on again, follow the same

procedure.

17

AUTOMATIC FAULT SIGNALS

Turn off the dishwasher, open the

inlet hose and reset the cycle.

Check if the drain tube is bent or if

the siphon or filters are clogged.

If the problem persists, contact

Customer Service.

Check if the drain tube is bent or if

the siphon or filters are clogged.

If the problem persists, contact

Customer Service.

Contact Customer Service.

Clean the filter plate.

If the problem persists, contact

Customer Service.

FAULTS CAUSE SOLUTION

E2

appears on the display and

the alarm sounds.

E3 appears on the display and

the alarm sounds.

E4 appears on the display and

the alarm sounds.

E5,E6,E7,Ef or EL appears

on the display and the alarm

sounds.

E8 or Ei appear on the display

and the alarm sounds.

No water (inlet hose closed).

The machine cannot drain water.

Water leak

Electronic control fault.

The water heating element is not

working correctly or the filter plate is

clogged.

The dishwasher is able to signal a series of faults in the display.

4. Press the same button again ("A1" will

appear on the display to indicate that the

memorization is on).

5. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

To disable the memorization, follow the

same procedure.

IMPORTANT

This dishwasher is equipped with an

anti-overflow safety device which will

automatically discharge any excess

water should a problem occur.

WARNING!

To ensure the correct operation of

the anti-overflow safety device, we

recommend that the dishwasher is

not moved or tilted during operation.

If however it is necessary to tilt or

move the dishwasher, please ensure

that the washing cycle is complete

and that there is no remaining water

inside the dishwasher.

Memorization of the last

programme used

The last programme used can be

memorized by following the below:

IMPORTANT

The dishwasher must ALWAYS be off

before start of this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 30 seconds

(during this time, 3 audible signals will

sound).

3. Release the button when the THIRD

audible signal sounds ("A0 " will appear

on the display to indicate that the

memorization is off).

Wash with prewash

For wash programmes with prewash, it is advisable to add a second dose of detergent (max.

10 g) directly in the machine.

Programme

PROGRAMME GUIDE

Description

Once a day - for normal soiled pans and any other

items that have been left all day for washing.

Programme for normally soiled tableware (the

most efficient in terms of its combined energy and

water consumption for that type of tableware).

Programme standardised to EN 50242.

An antibacterial cycle, intended for washing and

sterilising dishes (even heavily stained ones)

babies’ bottles etc.

Fast cycle, for “normally” dirty dishes - intended

for frequent washes and normal loads.

Suitable for heavily soiled items that are to be

washed straight after a meal (Max 8 place load).

Quick wash for dishes which are to be washed

immediately after the meal. Wash load of

6 persons.

Suitable for delicate crockery and glassware. Also

for less soiled items excluding pans.

Short cold pre-wash for items that are stored in

the dishwasher until you are ready to wash a full

load.

Quietest washing cycle. Ideal for functioning by

night and for taking advantage of reduced energy

fares.

= "IMPULSE" programmes

N/A = OPTION NOT AVAILABLE

Hygienic

75°C

Universal

60°C

Daily

55°C

Eco

45°C

Delicate

45°C

Rapid 59'

65°C

Ultra Rapid 24'

50°C

Ultra Silent

55°C

Refresh

Dishwasher Cleaner

This programme should be used periodically with

specialist dishwasher cleaning products. For all

cleaning operations the dishwasher must be empty.

18

YES

•••

•

130

75°C

•••

•

•••

•

•••

•

•••

•

240

170

59

24

5

55°C

45°C

65°C

50°C

•••

•

•••

•

120

80

60°C

55°C

•

•••

•

85

45°C

45

70°C

Check list

Avarage

duration

in minutes

Special function

buttons

available

Detergent for soaking

(Prewash)

Detergent for washing

Clean filter

Check rinse aid

dispenser

Check salt container

Hot pre-wash

Cold pre-wash

Main wash

First cold rinse

Second cold rinse

Hot rinse with rinse aid

With cold water (15°C)

*

-Tolerance ± 10%-

"DELAY START" button

“EXPRESS” button

"ALL IN 1" button

Programme contents

YES

N/A

*

WITH HOT WATER THE TIME REMAINING UNTIL THE END OF THE PROGRAMME IS

AUTOMATICALLY DISPLAYED WHILE THE PROGRAMME IS RUNNING.

19

20

The water-stop device protects against water damages caused by leaks on the fill

hose which could develop due to natural ageing of the hose.

In the water-stop system the leaking water fills the corrugated hose and activates a

stop valve which cuts off the water supply to the machine.

This fault is shown by a red sector on the window .

Would this occur, please refer to your Service Agent.

If the hose is not long enough for correct connection, it must be replaced with a longer

one. The hose can be obtained from your Service Agent.

Safety antitwist device (press and twist to remove the washer).

AQUASTOP-SYSTEM

* The softener unit is set in the factory

at level 4 (d4) as this satisfies the

requirements of the majority of users.

Regulate the setting of your water softener

unit according to the degree of hardness

of your water as follows:

IMPORTANT

The dishwasher must ALWAYS be

off before start of this procedure.

1. Hold down the "PROGRAMME

SELECTION" button and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME SELECTION"

button pressed for at least 5 seconds,

UNTIL an audible signal sounds. The

current water softener setting level will

be shown on the display.

3. Press the same button again to select

the required water softener level: each

time the button is pressed, the setting

will increase by one level. When you

have reached "d7", the display will go

back to "d0".

4. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

WARNING!

If any problem occurs, turn the

dishwasher off by pressing the

"ON/OFF" button and start the

procedure again from the beginning

(STEP 1).

WATER SOFTENER UNIT

Depending on the source of the supply,

water contains varying amounts of limestone

and minerals which are deposited on the

dishes leaving whitish stains and marks.

The higher the level of these minerals

present in the water, the harder the water is.

The dishwasher is fitted with a water

softener unit which, through the use of

special regenerating salt, supplies

softened water for washing the dishes.

The degree of hardness of your water can

be obtained from your water supply

company.

Regulating the water softener

with electronic programmer

The water softener can treat water with a

hardness level of up to 90°fH (French

grading) or 50°dH (German grading)

through 8 settings.

The settings are listed in the table below:

NO

YES

0

1

2

3

*4

5

6

7

0-5

6-10

11-20

21-30

31-40

41-50

51-60

61-90

0-3

4-6

7-11

12-16

17-22

23-27

28-33

34-50

Level

°fH

(French)

°dH

(German)

d0

d1

d2

d3

d4

d5

d6

d7

Water

hardness

Water

softener

setting

Use of

regenerating

salt

“ON/OFF” button

21

"PROGRAMME SELECTION"

button

DIGITAL DISPLAY

Page is loading ...

29

•••

•

130

75°C

•••

•

•••

•

•••

•

•••

•

240

170

59

24

5

55°C

45°C

65°C

50°C

*AVEC DE L'EAU CHAUDE LE TEMPS RESTANT AVANT LAFIN DU PROGRAMME DE LAVAGE EST

AUTOMATIQUEMENTAFFICHÉ EN COURS DE CYCLE.

OUI

•••

•

•••

•

120

80

60°C

55°C

OUI

•

•••

•

85

45°C

OUI

45

70°C

OUI

N/A

OUI

Opérations à accomplir

Durée

moyenne

en

minutes

Fonctions

facultatives

Lessive prélavage

Lessive lavage

Nettoyage plaque,

filtre

Contrôle provision

du produit de rinçage

Contrôle provision

Sel

Prélavage chaud

Prélavage froid

Lavage

Premier rinçage

à

froid

Second rinçage

à

froid

Rinçage chaud avec-

produit de rinçage

Avec eau froide (15°C)

*

(Tolerance ±10%)

Touche

“DEPART DIFFERE”

Touche “EXPRESS”

Touche “ALL IN 1”

Déroulement du programme

Page is loading ...

Questo elettrodomestico è marcato conformemente alla Direttiva Europea 2012/19/UE sui Rifiuti da Apparecchiature Elettriche

ed Elettroniche (RAEE).

I RAEE contengono sia sostanze inquinanti (che possono cioè avere un impatto negativo anche molto pesante sull’ambiente)

sia materie prime (che possono essere riutilizzate). E’ perciò necessario sottoporre i RAEE ad apposite operazioni di tratta-

mento, per rimuovere e smaltire in modo sicuro le sostanze inquinanti ed estrarre e riciclare le materie prime.

Ogni cittadino può giocare un ruolo decisivo nell’assicurare che i RAEE non diventino un problema ambientale; basta seguire

qualche semplice regola:

- i RAEE non vanno mai buttati nella spazzatura indifferenziata;

- i RAEE devono essere consegnati ai Centri di Raccolta (chiamati anche isole ecologiche, riciclerie, piattaforme ecologiche

…) allestiti dai Comuni o dalle Società di igiene urbana; in molte località viene anche effettuato il servizio di ritiro a domicilio

dei RAEE ingombranti.

In molte nazioni, quando si acquista una nuova apparecchiatura, si può consegnare il RAEE al negoziante, che è tenuto a riti-

rarlo gratuitamente (ritiro "uno contro uno") a patto che il nuovo apparecchio sia dello stesso tipo e svolga le stesse funzioni di

quello reso.

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment

(WEEE).

WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic compo-

nents (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and dispose

properly all pollutants, and recover and recycle all materials.

Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow

some basic rules:

- WEEE should not be treated as household waste;

- WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In

many countries, for large WEEE, home collection could be present.

In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of

charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied

equipment.

Cet appareil est commercialisé en accord avec la directive européenne 2012/19/EU sur les déchets des équipements

électriques et électroniques (DEEE).

Les déchets des équipements électriques et électroniques (DEEE) contiennent des substances polluantes (ce qui peut

entraîner des conséquences négatives pour l’environnement) et des composants de base (qui peuvent être réutilisés). Il est

important de traiter ce type de déchets de manière appropriée afin de pouvoir éliminer correctement tous les polluants et de

recycler les matériaux.

Les particuliers peuvent jouer un rôle important en veillant à ce que les DEEE ne deviennent pas un problème

environnemental. Il est essentiel de suivre quelques règles simples:

- Les DEEE ne doivent pas être traités comme les déchets ménagers;

- Les DEEE doivent être remis aux points de collecte enregistrés. Dans de nombreux pays, la collecte des produits gros

électroménagers peut être effectuée à domicile.

Dans de nombreux pays, lorsque vous achetez un nouvel appareil, l’ancien peut être retourné au détaillant qui doit collecter

gratuitement sur la base un contre un. L’équipement repris doit être équivalent ou bien avoir les mêmes fonctions que le

produit acquis.

Page is loading ...

La Ditta costruttrice declina ogni responsabilità per eventuali errori di stampa contenuti

nel presente libretto. Si riserva inoltre il diritto di apportare le modifiche che si

renderanno utili ai propri prodotti senza compromettere le caratteristiche essenziali.

Per consultare la scheda tecnica relativa al prodotto, fare riferimento al sito web del pro-

duttore.

The manufacturer declines all responsibility in the event of any printing mistakes in this

booklet. The manufacturer also reserves the right to make appropriate modifications to

its products without changing the essential characteristics.

To consult the product fiche, please refer to the manufacturer website.

Le constructeur décline toute responsabilité pour les éventuelles erreurs d’imprimerie

contenues dans le présent mode d’emploi. Il se réserve en outre le droit d’apporter

toutes modifications qui se révèleraient utiles à ses propes produits sans pour autant

en compromettre les caractéristiques essentielles.

Pour voir la fiche technique du produit, reportez-vous au site web du fabricant.

Wir schileßen die Haftung für alle evtl. Druckfehler aus. Kleinere Änderungen und

technische Weiterentwicklungen im Detail vorbehalten.

Für die technischen Daten des Produktes schauen Sie bitte auf der Internetseite des

Herstellers nach.

Wij stellen ons niet aansprakelijk voor eventuele drukfouten. Kleine veranderingen en

technische ontwikkelingen zijn voorbehouden.

Om de productfiche te raadplegen, verwijzen wij u door naar de website van de

fabrikant.

Page is loading ...

Candy CDPM 77883X User manual

This manual is also suitable for

Candy CDPM 77883X User manual

in other languages

Related papers

Other documents