Porsche USB-CDR30 Quick Installation Manual

Brand: Porsche

Model: USB-CDR30

Type: Quick Installation Manual

Courtesy of:DiscountCarStereo.com

USB-CDR30

Quick

Quick Quick

Quick Start

Start Start

Start Install

InstallInstall

Installation

ationation

ation

Guide for

Guide for Guide for

Guide for

PoPo

Porsche CDR30

rsche CDR30rsche CDR30

rsche CDR30/31

/31/31

/31

Radios

adiosadios

adios

Revised: January 10, 2018

Introduction:

Introduction:Introduction:

Introduction:

Portable audio products are everywhere, reflecting demand from

active people all over the world to take their music with them.

Porsche offers an optional 3.5mm jack for the CDR30

optional 3.5mm jack for the CDR30 optional 3.5mm jack for the CDR30

optional 3.5mm jack for the CDR30 and CDR31

and CDR31 and CDR31

and CDR31

Radio

Radio Radio

Radio which may be satisfactory to some, but those looking for a

better solution we offer the USB-CDR30.

. The USB-CDR30 replaces

the optional 3.5mm jack and allows the user to play and charge

play and chargeplay and charge

play and charge all

Apple lightning devices without sacrificing the look and feel of the

dashboard components

Installation:

Installation:Installation:

Installation:

Warning!

Warning!Warning!

Warning!

Although not critical, we recommend disconnecting the car

battery.

1. Remove CDR30/31 radio from dashboard to gain access to

the connectors. (Radio removal not covered in these

instructions)

2. With radio removed disconnect factory Quadlock plug

(harness) from Radio (See Fig. 1

Fig. 1Fig. 1

Fig. 1 )

Fig. 1

Fig. 1Fig. 1

Fig. 1

Factory Quadlock

3. To remove radio plug, push up on tab (indicated by black

arrow in F

2) and pull outwards on lock release

4. Connect plug on adapter harness to Radio (See To Radio in

in in

Fig. 3

Fig. 3Fig. 3

Fig. 3)

5. Disconnect the 12-pin green

greengreen

green and blue

blueblue

blue mini-Quadlock plugs

from factory plug (See Fig. 1

Fig. 1Fig. 1

Fig. 1)

Warning!

Warning!Warning!

Warning!

CDR30/31 Radios with factory AUX and Bluetooth will

have both a blue and green 12-pin mini-Quadlock (Green

reenreen

reen for AUX

and blue

blueblue

blue for Bluetooth). The AUX mini-Quadlock remains

disconnected and replaced with the black

blackblack

black 12-pin mini-Quadlock

from Adapter. (See Fig. 2

Fig. 2Fig. 2

Fig. 2)

6. Reconnect 12-pin blue

blueblue

blue mini-Quadlock plug (from step 5) to

plug on adapter harness (To Radio in Fig. 3

Fig. 3Fig. 3

Fig. 3)

Fig. 2

Fig. 2Fig. 2

Fig. 2

Quadlock Plug on Adapter harness

Green sub

Green subGreen sub

Green sub-

-plug remains disconnected

plug remains disconnectedplug remains disconnected

plug remains disconnected (See Fig. 2

Fig. 2Fig. 2

Fig. 2)

7. Connect factory plug (from step 2) to mating connector on

Adapter harness (To Car in Fig.

Fig.Fig.

Fig.

Fig. 3

Fig. 3Fig. 3

Fig. 3

plug/connector on adapter harness

Ensure connections are snug

Ensure connections are snugEnsure connections are snug

Ensure connections are snug

Note to Vehicles with BOSE:

Note to Vehicles with BOSE: Note to Vehicles with BOSE:

Note to Vehicles with BOSE: You must transfer optical cable

You must transfer optical cable You must transfer optical cable

You must transfer optical cable

from factory

from factoryfrom factory

from factory

plug to

plug to plug to

plug to plug

plug plug

plug supplied with adapte

supplied with adaptesupplied with adapte

supplied with adapter.

r.r.

8. Decide where and how to mount USB terminal.

A. Flush mount requires drilling a ¾” hole in the dash

Flush mount requires drilling a ¾” hole in the dashFlush mount requires drilling a ¾” hole in the dash

Flush mount requires drilling a ¾” hole in the dash

B. USB mounting bracket

USB mounting bracket USB mounting bracket

USB mounting bracket without drilling

without drillingwithout drilling

without drilling (use this option

to mount the USB terminal wherever your installation

demands)

C. Un

UnUn

Un-

-mounted

mountedmounted

mounted (Free standing USB terminal)

A.A.

A. Flush Mounting

Flush Mounting Flush Mounting

Flush Mounting to

to to

to Dash

DashDash

Dash

1. Drill a ¾” hole in dash using a step drill bit or equivalent

(See Fig. 4

Fig. 4Fig. 4

Fig. 4)

Fig. 4

Fig. 4Fig. 4

Fig. 4

Step drill bit

2. Insert the male end of the 3ft USB extension cable (See Fig. 5

Fig. 5Fig. 5

Fig. 5)

through the ¾” hole in dash and mate with USB Female

terminal on adapter (See Fig. 6

Fig. 6Fig. 6

Fig. 6)

Fig. 5

Fig. 5Fig. 5

Fig. 5

USB extension cable

Fig. 6

Fig. 6Fig. 6

Fig. 6

USB Male (left) USB Female (Right)

3. Push USB head ( See Fig. 7

Fig. 7Fig. 7

Fig. 7) through hole until it snaps in

place and flush with mounting surface (See Fig. 8

Fig. 8Fig. 8

Fig. 8)

Fig. 7

Fig. 7Fig. 7

Fig. 7

Flat USB Terminal

Fig. 8

Fig. 8Fig. 8

Fig. 8

Flush mounted USB terminal

4. Tuck and secure extra wire from moving parts and test

operation (See Enabling the AUX

Enabling the AUXEnabling the AUX

Enabling the AUX section below)

B.B.

Mounting Bracket

Mounting Bracket Mounting Bracket

Mounting Bracket without drilling

without drillingwithout drilling

without drilling

1. Locate a flat surface at location of choice within 7 ft. of radio

to mounting bracket to surface using adhesive/tape or screws.

(See Fig. 9

Fig. 9Fig. 9

Fig. 9)

Fig. 9

Fig. 9Fig. 9

Fig. 9

mounting bracket

2. Insert male end of 3ft USB extension cable through hole in

bracket (See Fig. 10

Fig. 10Fig. 10

Fig. 10) and mate with Female USB terminal

from Adapter (See

Fig. 11

Fig. 11Fig. 11

Fig. 11)

Fig. 10

Fig. 10Fig. 10

Fig. 10

USB Male (left) USB Female (right)

Fig. 11

Fig. 11Fig. 11

Fig. 11

USB Male (left) USB Female (Right)

3. Push USB head through hole in mounting bracket until it

snaps in place and flush (See Fig 12

Fig 12Fig 12

Fig 12)

Fig. 12

Fig. 12Fig. 12

Fig. 12

4. Tuck and secure extra wire away from moving parts and test

operation (

See Enabling the AUX section

See Enabling the AUX sectionSee Enabling the AUX section

See Enabling the AUX section

)

C.C.

C. Un

UnUn

Un-

-Mounted (Free

Mounted (Free Mounted (Free

Mounted (Free Standing)

Standing) Standing)

Standing)

USB Terminal

USB TerminalUSB Terminal

USB Terminal

Simply route USB terminal (See Fig. 13

Fig. 13Fig. 13

Fig. 13) from behind the dash to

location of choice within 4 ft. of radio and connect your Apple

lightning cable.

Fig. 13

Fig. 13Fig. 13

Fig. 13

Free standing USB Terminal

Test Operation

Test OperationTest Operation

Test Operation

1. Connect Apple device to USB Terminal

2. Audio device will begin charging

3. On Radio, press CD/AUX

CD/AUXCD/AUX

CD/AUX button repeatedly until “AUX

AUX AUX

AUX

Mode

ModeMode

Mode” is enabled.

Note: To switch from CD to AUX press the “AUX” Soft key.

4. Select a track from devices music library and it will play on

the car speakers.

Warning!

Warning!Warning!

Warning! Playlist and Track selection is *NOT* possible from the

radio. You must use the iPod built-in controls to access music files.

5. Use the radio volume control to set playback level

6. If successful operation is confirmed go ahead and reinstall

Radio

Alert!

Alert!Alert!

Alert! Apple authentic Lighting cable is required for proper

operation. Knock –off Lightning cables will charge but may not

play music.

Compatibility

CompatibilityCompatibility

Compatibility

The USB-CDR30 works on the following Apple Lighting devices.

iPhone Models iPad Models iPod Models

iPhone X

iPhone 8

iPhone 8 Plus

iPhone 7

iPhone 7 Plus

iPhone 6s

iPhone 6s Plus

iPhone 6

iPhone 6 Plus

iPhone SE

iPhone 5s

iPhone 5c

iPhone 5

iPad Pro 10.5-inch

iPad Pro 12.9-inch (2G)

iPad Pro 12.9-inch (1G)

iPad Pro 9.7-inch

iPad

iPad mini 4

iPad mini 3

iPad mini 2

iPad mini

iPad Air 2

iPad Air

iPod touch 6G

iPod touch 5G

iPod nano 7G

Disclaimer

DisclaimerDisclaimer

Disclaimer

• This product has no affiliation with Porsche or Apple

• There are no warranties expressed or implied by purchase of this product

•Aux must be enabled, otherwise visit your Porsche dealer for assitance

• We’re not liable for misuse of this product.

•We recommend professional installation.

Call 804-717-5717 or email support@discountcarstereo.com

subject to change without notice. Other products and companies referred to herein are

trademarks or registered trademarks of their respective companies or mark holders.

Porsche USB-CDR30 Quick Installation Manual

Porsche USB-CDR30 Quick Installation Manual

Porsche USB-CDR30 Quick Installation Manual

Related papers

Other documents