Rust-Oleum Stops Rust 7214502 User manual

Brand: Rust-Oleum Stops Rust

Model: 7214502

Type: User manual

This manual is also suitable for

TECHNICAL DATA SRT-06

STOPS RUST

HAMMERED BRUSH

Form: GDH-707

Rev.: 022615

.DESCRIPTION AND USES .

Rust-Oleum

Stops Rust

Hammered Metal Finish provides

long-lasting protection that seals out moisture and protects the

underlying surface against corrosion. The unique hammered

texture covers imperfect surfaces, eliminating the need to sand to

bare metal or prime. The hammered finish is ideal for weathered

and sound rusted metal. It decorates and protects metal, wood,

concrete, stone, and more. Not for use on galvanized steel.

.PRODUCTS .

SKU (1-Quart) Description

239073 Brown

239074 Copper

239075 Dark Bronze

7210502 Gold Rush

7211502 Deep Green

7213502 Silver

7214502 Gray

7215502 Black

..PRODUCT APPLICATION .

PAINTING CONDITIONS

Apply only when air and surface temperatures are

between 60-90°F (15-32°C) and humidity is below 85% to

ensure proper drying. Do not apply to surfaces that will

exceed 200°F (93°C). Do not use on galvanized steel.

SURFACE PREPARATION

ALL SURFACES: Remove all dirt, grease, oil, salt and

chemical contaminants by washing the surface with a

commercial detergent or other suitable cleaning method.

Rinse thoroughly with fresh water and allow to fully dry. All

surfaces must be dry at time of application.

STEEL: Scrape and wire brush or power tool clean to

remove loose rust, scale and deteriorated previous

coatings. Use 7769 Rusty Primer for sound rusted or clean

metal before application of a finish coat. 7780 White Clean

Primer is best for clean metal but may be used on sound

rusted metal as well.

..PRODUCT APPLICATION (cont.) .

PREVIOUSLY COATED: Previously coated surfaces must

be sound and in good condition. Smooth, hard, or glossy

finishes should be scarified by sanding to create a surface

profile. The Stops Rust

Hammered Enamels are

compatible with most coatings, but a test patch is

suggested.

WARNING! If you scrape, sand or remove old paint from

any surface, you may release lead paint dust. LEAD IS

TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE

SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;

ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH

approved respirator to control lead exposure. Clean up

carefully with a HEPA vacuum and a wet mop. Before you

start, find out how to protect yourself and your family by

contacting the National Lead Information Hotline at 1-800-

424-LEAD or log on to www.epa.gov/lead.

APPLICATION

Before using, stir thoroughly to ensure any settled pigment

is re-dispersed. If necessary, thin the material with xylene.

For brush or roller, thinning is not normally required. For

air spray, thin up to 15% with xylene. Do not thin with

gasoline, lacquer thinner, turpentine, etc. For airless spray,

thinning is not normally required. Apply with a good quality

brush, roller or spray gun.

DRY & RECOAT TIMES

Dry and recoat times are based on 70°F and 50% relative

humidity. Allow more time at cooler temperatures and

higher humidity. Apply 2 coats for full coverage, best

appearance and maximum rust protection. Make sure that

corners, edges and heavily pitted areas are adequately

covered. Apply a second coat after the first coat is dry to

the touch (30 minutes). Second coat must be applied

within 4 hours or after 7 days. Dries to handle in 60-90

minutes and is fully dry in 24 hours.

CLEAN-UP

Clean brush and tools with xylene.

TECHNICAL DATA

STOPS RUST

HAMMERED BRUSH

Rust-Oleum Corporation Form: GDH-707

11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 022615

Vernon Hills, Illinois 60061 www.rustoleum.com

An RPM Company⅗

PHYSICAL PROPERTIES .

STOPS RUST HAMMERED BRUSH

Resin Type

Modified alkyd

Pigment Type

Varies with color

Solvents

Aromatic Hydrocarbons

Weight

Per Gallon

7.6-7.8 lbs

Per Liter

0.9-0.93 kg

Solids

By Weight

51.5-52.5%

By Volume

44.5-45.5%

Volatile Organic Compounds

<450 g/l (3.75 lbs./gal.)

Recommended Dry Film

Thickness (DFT) Per Coat

1.0-2.0 mils

(25-50µ)

Wet Film to Achieve DFT

2.0-4.0 mils

(50-100µ)

Theoretical Coverage at

1 mil DFT (25µ)

178-182 sq.ft./qt.

(17.5-17.9 m

/l)

Practical Coverage at Recommended

DFT

75-150 sq.ft./qt.

(7.4-14.8 m

/l)

Dry Times at 70-80°F

(21-27°C) and 50%

Relative Humidity

Touch

30 minutes

Handle

60-90 minutes

Recoat

Within 4 hours or after 7 days

Dry Heat Resistance

200°F (93°C)

Shelf Life

5 years

Flash Point

52°F (11°C)

Safety Information

For additional information, see MSDS

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature

do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we

can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All