Amerock BP54025BBR Installation guide

BP54025BBR
Brand
Amerock
Model
BP54025BBR
Type
Installation guide
18in CTC 18in CTC
Tape edge of LEFT-PAGE 1 here
RIGHT-PAGE 2
• Clear Tape
• Pencil
• Level
• Ruler
• 3/16in Drill Bit
• Drill
Items Required
Printable Mounting Template for use with 18in(457mm) CTC Appliance Pull
Read all instructions prior to installing.
Questions? Contact Amerock customer service at 800-435-6959.
Amerock is not responsible for incorrect drilling or damage to mounting surface.
Visit Amerock.com to download and print 8in(203mm) and 12in(305mm) CTC Appliance Pull templates.
1a. Print both pages at 100% scale on
letter-sized (8.5in x 11in) paper. Do not
scale to fit.
1b. To assemble the template, use clear
tape to attach the right edge of this page
(Left-Page 1) to the heavy dashed line on
Right-Page 2.
1c. Once complete, check the 18in
center-to-center (CTC) distance with a
ruler to ensure it measures exactly 18in.
STEP 1: Assembling This Template
2a. Once you have assembled and
checked this template, decide where
you want to mount your appliance
pull. In the following steps, you will
draw a centerline and tick mark on
the cabinet or drawer surface to
help you align this template and
mark drill holes.
2b. Use a level and pencil to lightly
draw a straight centerline on the
cabinet or drawer surface (refer
to Figure 1 or 2). This centerline
will indicate the orientation and
placement of the appliance pull.
2c. Next, make a tick mark on your
drawn centerline to indicate where
you would like the middle point of the
appliance pull (refer to Figure 1 or 2).
2d. Align the top edge of this template
with your drawn centerline on the
cabinet or drawer, and be sure Template
Centerline is aligned with the tick mark
you drew in Step 2c.
2e. Holding the template in place, tape it
to the cabinet or drawer. Using the 18in
CTC line above as a guide, lightly mark
on drawn centerline the two points
where you will need to drill (refer to
Figure 3).
2f. Before drilling, remove template and
use level to re-check that the drawn
centerline is properly aligned with the
cabinet or drawer. If not, erase all marks
and repeat Steps 2b-2f. You are now
ready to proceed with drilling and
installation.
STEP 2: Using This Template
Amerock
®
| 10115 Kincey Ave, Huntersville, NC 28078 | 800-435-6959 | Amerock.com
LEFT-PAGE 1
© 2018 © 2018
Figure 1
Drawing centerline and tick mark
for vertical mounting
Drawn
centerline
Tick mark to
indicate middle
point of pull
Figure 3
Marking drill holes on drawn centerline
Figure 2
Drawing centerline and tick mark for horizontal mounting
Template Centerline
Drawn
centerline
Tick mark to
indicate middle
point of pull
Align Template Centerline
with drawn tick mark
18in CTC 18in CTC
Tape edge of LEFT-PAGE 1 here
RIGHT-PAGE 2
• Clear Tape
• Pencil
• Level
• Ruler
• 3/16in Drill Bit
• Drill
Items Required
Printable Mounting Template for use with 18in(457mm) CTC Appliance Pull
Read all instructions prior to installing.
Questions? Contact Amerock customer service at 800-435-6959.
Amerock is not responsible for incorrect drilling or damage to mounting surface.
Visit Amerock.com to download and print 8in(203mm) and 12in(305mm) CTC Appliance Pull templates.
1a. Print both pages at 100% scale on
letter-sized (8.5in x 11in) paper. Do not
scale to fit.
1b. To assemble the template, use clear
tape to attach the right edge of this page
(Left-Page 1) to the heavy dashed line on
Right-Page 2.
1c. Once complete, check the 18in
center-to-center (CTC) distance with a
ruler to ensure it measures exactly 18in.
STEP 1: Assembling This Template
2a. Once you have assembled and
checked this template, decide where
you want to mount your appliance
pull. In the following steps, you will
draw a centerline and tick mark on
the cabinet or drawer surface to
help you align this template and
mark drill holes.
2b. Use a level and pencil to lightly
draw a straight centerline on the
cabinet or drawer surface (refer
to Figure 1 or 2). This centerline
will indicate the orientation and
placement of the appliance pull.
2c. Next, make a tick mark on your
drawn centerline to indicate where
you would like the middle point of the
appliance pull (refer to Figure 1 or 2).
2d. Align the top edge of this template
with your drawn centerline on the
cabinet or drawer, and be sure Template
Centerline is aligned with the tick mark
you drew in Step 2c.
2e. Holding the template in place, tape it
to the cabinet or drawer. Using the 18in
CTC line above as a guide, lightly mark
on drawn centerline the two points
where you will need to drill (refer to
Figure 3).
2f. Before drilling, remove template and
use level to re-check that the drawn
centerline is properly aligned with the
cabinet or drawer. If not, erase all marks
and repeat Steps 2b-2f. You are now
ready to proceed with drilling and
installation.
STEP 2: Using This Template
Amerock
®
| 10115 Kincey Ave, Huntersville, NC 28078 | 800-435-6959 | Amerock.com
LEFT-PAGE 1
© 2018 © 2018
Figure 1
Drawing centerline and tick mark
for vertical mounting
Drawn
centerline
Tick mark to
indicate middle
point of pull
Figure 3
Marking drill holes on drawn centerline
Figure 2
Drawing centerline and tick mark for horizontal mounting
Template Centerline
Drawn
centerline
Tick mark to
indicate middle
point of pull
Align Template Centerline
with drawn tick mark
  • Page 1 1
  • Page 2 2

Amerock BP54025BBR Installation guide

BP54025BBR
Brand
Amerock
Model
BP54025BBR
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents