Griffin MD-AP3372 User manual

Brand: Griffin

Model: MD-AP3372

Type: User manual

www.Griffin-Stands.com

Speaker Wall

Mount

Brackets

www.Griffin-Stands.com

Griffin™ stands and accessories are manufactured

in several innovative factories responsible for

developing products that address the newest

needs and trends of the current market. We take

pride in the Griffin™ brand and endeavor to be on

the forefront of the musical stands and musical

and lighting accessories market.

Performance Issue, Uneven or Unstable- Make

sure all nuts and bolts are tight on the product. If they

are, then loosen all nuts and bolts 1 full turn counter-

clockwise, then go back and tighten each bolt only ½

turn tight. Then do a final tighten turn for another ½

turn tight. Next, Make sure there are not any missing

nuts or bolts. Third, ensure all parts on the product

are not broken or defective. Finally, Re-read the

assembly instructions or watch the product

demonstration video to ensure you have correctly

assembled or are using the product properly with

factory specifications.

Missing Parts- The pictures, videos and images

shown in this manual might have changed style or

count due to the product being redesigned. So in rare

cases the part may no longer be included or of a

different style. However, if you think you are missing

a part that is necessary to the assembly and use of

your product, then first carefully double check all

packaging for any parts you think are missing. Some

parts might be hiding in the packaging or loose in an

inner box.

User Manual

M o d e l # A P 3 3 7 2

Griffin | 11408 Hwy 64 W, Tyler, TX 75704 |

info@griffin-stands.com | www.Griffin-

Stands.com

For current product specifications, please to go

www.griffin-stands.com and type the model number

into the search bar. Locate the product listing to view

the current factory specifications.

Thank you for purchasing the Griffin Speaker Wall

Mount Brackets. Your product comes with a 1 year

factory warranty from purchase date. Please read all

assembly instructions prior to assembling your new

cart. Pictures that may aid in assembly can be found

by going to www.griffin-stands.com and typing

AP3372 into the search bar.

Step 4 – Drill into the marked holes and insert the

threaded plastic anchors to each hole, a hammer might

be needed to insert these.

Step 7 – For safety

reasons, please always

make sure to test the

stability and safety of

the product before

use. Double check all

nuts and bolts, knobs

and connectors, make

sure that these are

tight and securely

fastened before use of

your product. Test the

product under light use

or light loads the first

time to confirm

assembly and structure

of the product is

correct.

Step 1 - Align the two tilt adjustment arms and insert

the top arm into the bottom arm and insert the pin

into one of the holes. The amount of tilt that you want

determines which hole to insert the pin into, please

see Figure 1.

Step 2 – As shown in

Figure 2, the speaker

post mount is screwed

in one of the 3

different holes on the

adjacent steel bar. It

depends on your

preference to where

you would want the

mount to be screwed

in. You may use a

wrench to counter the

bolt while tightening

the speaker post

mount.

Step 3 – To mount the bracket to the wall, take the

bracket and measure the height if it suits your

preference. Mark the holes to where you should drill to

mount the brackets. Make sure that everything is

leveled to avoid the bracket leaning on one side and

making it a risk for your items to fall. See Figure 3.

Step 5 – Take the bracket and mount it on the wall, align

each hole on the wall to the brackets. Screw in first one

at the top and one at the bottom (do not tighten

immediately). Next is insert all the other screws in the

holes and adjust the tightness of each screw one by one,

this is to make sure that one side is not over tightened

and the brackets will be leaning over to one side.

Please scan the QR Code below for the product

demonstration video. Or go to the URl shown here and find

the product video. www.Griffin-Stands.com/Videos

Step 6 – The loop on

the side is used to

insert the cables to be

connected to the back

of the speakers. (See

Figure 4).

Always check the integrity of the speaker wall mount

bracket before mounting anything. You may hold onto

the speaker post mount and grip it tightly and wiggle the

brackets to test.

Griffin MD-AP3372 User manual

Griffin MD-AP3372 User manual

Griffin MD-AP3372 User manual

Related papers

Other documents