INSTRUCTION SHEET
NOTE: Each keyless access transmitter is coded to prevent another
transmitter from working with your vehicle. If a transmitter is lost or
stolen, a replacement can be purchased. Remember to have any
remaining transmitters with you when program a new transmitter.
Once you have coded the new transmitter, the lost transmitter will
not work with your vehicle. Each vehicle can have a maximum of four
transmitters matched to it.
WHEN YOU HAVE A RECOGNIZED TRANSMITTER:
BEFORE YOU BEGIN:
1. The vehicle must be off.
2. Have the recognized and new, unrecognized transmitters on your
person.
3. Go to the rear of the vehicle and insert the vehicle key into the key
cylinder located on the lower rear fascia on the driver’s side of the
vehicle. See “Trunk” in your Owner’s Manual for more information
on the key cylinder.
4. Open the trunk.
PROGRAMMING INSTRUCTIONS:
1. Turn the key five times within five seconds.
2. The Driver Information Center (DIC) will display READY FOR FOB
#X. X can be 2, 3 or 4.
3. Place the new, unrecognized transmitter in the glove box transmitter
pocket with the buttons facing to the right.
4. Once the transmitter is programmed, a beep will sound. The DIC
will display READY FOR #X, where X can be 3 or 4, or MAX # FOBS
LEARNED.
TO EXIT PROGRAMMING MODE:
1. Press the ACC button.
TO MATCH A NEW TRANSMITTER TO THE VEHICLE WHEN A
RECOGNIZED TRANSMITTER IS NOT AVAILABLE:
The procedure will require three ten minute cycles to complete the
matching process.
KEY FOB PROGRAMMING INSTRUCTIONS -
10354922, 10354923, 10347463, 10347464
FOR AUTOMOBILES:
• 2004-2007 Cadillac XLR
REQUIRED TOOLS:
• None
INSTRUCTION SHEET
BEFORE YOU BEGIN:
1. The vehicle must be off.
2. Place the new, unrecognized transmitter in the glove box
transmitter pocket with the buttons facing to the right.
3. Go to the rear of the vehicle and insert the vehicle key into the key
cylinder located on the lower rear fascia on the driver’s side of the
vehicle. See “Trunk” in your owner’s manual for more information
on the key cylinder.
4. Open the trunk.
PROGRAMMING INSTRUCTIONS:
1. Turn the key five times within five seconds.
2. The DIC message will display OFF-ACC TO LEARN.
3. Press the ACC button.
4. The DIC will read WAIT 10 MINUTES and will count down to zero,
one minute at a time.
5. The DIC will display OFF-ACC TO LEARN again.
6. Press the ACC button.
7. The DIC will read WAIT 10 MINUTES and will count down to zero,
one minute at a time.
8. The DIC will display OFF-ACC TO LEARN again.
9. Press the ACC button.
10. The DIC will read WAIT 10 MINUTES and will count down to
zero, one minute at a time.
11. A beep will sound and the DIC will read READY FOR FOB #1. At
this time, all previously known transmitters have been erased.
12. Once the transmitter is recognized and programmed, a beep will
sound and the DIC will display READY FOR FOB #2.
NOTE: If you have additional transmitters to program, take transmitter
1 out of the transmitter pocket and place transmitter 2 in the pocket.
This can be done repeatedly until up to four transmitters have been
programmed. The DIC will then display MAX # FOBS LEARNED and
will exit the programming mode.
TO EXIT PROGRAMMING MODE:
1. Press the ACC button.
-
1
-
2
ACDelco 10347464 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Cadillac XLR 2004 Owner's manual
-
-
-
-
-
-
-
Chevrolet Corvette 2007 Owner's manual
-
-