Ledpax Technology SD4-3K Installation guide

Brand: Ledpax Technology

Model: SD4-3K

Category: Dimmers

Type: Installation guide

Ledpax Technology SD4-3K: This powerful and versatile device is designed to meet a wide range of needs, from basic home security to advanced automation tasks. With its built-in sensors, including motion detection, temperature sensing, and humidity monitoring, the SD4-3K can provide comprehensive surveillance and environmental monitoring capabilities.

CONSTRUCTION: Round&Square 4” and 6” fixtures with integral LEDs. Isolated external driver factory installed inside junction box. One driver for every fixture required.

Power Factor >0.95. LED fixture and driver are TYPE IC rated – approved for direct contact with insulation. Pot light housing is NOT required even for insulated

ceilings. Lifespan: 36,000 hours.

Suitable for category 1 damp locations and soffit installations. Not waterproof – DO NOT expose to rain.

ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.

INSTALLATION:

CONNECTING THE DRIVER: Locate the driver next to the fixture. Open the cover of the junction box. Push and remove one of the half-inch knockouts on the side

plate. Install cable connector. Use double connector for daisy chaining multiple drivers. Insert line voltage feed into the cable connector and splice same colour

wires using Quick Connectors. Close the cover. Connect the driver to the light fixture – the arrows on the male and female parts of the connector between the

driver and the fixture should match. Tighten the connector by hand. Do not attach the junction box to anything so you can pull it through the ceiling opening in

case you need to service the driver in the future.

INSTALLATION INSTRUCTIONS AND WARRANTY INFORMATION FOR RECESSED LED FIXTURE MODELS: AFR4, AFR6

DIMMING (120V only): We recommended LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer, adjust the dial

to the lowest position before the lights start to flicker or shut down. This setting depends on the local voltage and number of fixtures per dimmer. For a typical

LED dimmer rated for 150W LED load the maximum number of fixtures per dimmer is: model: AFR4 – 16, AFR6 – 12.

WARNING: DO NOT USE ANY OTHER DRIVERS EXCEPT THE DRIVERS THAT ARE INCLUDED WITH THE FIXTURE. DO NOT CONNECT MULTIPLE FIXTURES TO ONE

DRIVER. DO NOT OPEN THE LIGHT FIXTURE OR THE SIDE PLATES OF THE DRIVER – NO SERVICEABLE PARTS INSIDE.

Model

4" 6"

Input 120V AC 60Hz 9W 120V AC 60Hz 12W

Output 18-33V DC 350MA 18-33V DC 350MA

Lamp Life 36000 Hours 36000 Hours

Approved Location Damp Damp

Operating Temperature -40°C +40°C -40°C +40°C

Energy used 9W 12W

Luminous Flux

Warm:570-580LM

Neutral:635-650LM

Warm:850-860LM

Neutral:935-950LM

Equivalent to: 50W halogen 65W halogen

CCT Options

3000K/4000K/5000K/6000K 3000K/4000K/5000K/6000K

Beam Angle 110 Degree 110 Degree

CRI Ra>80 Ra>80

OD 5"(127MM) 6-7/8"(174MM)

ID 4-1/8"(104MM) 6-3/16"(156MM)

Thicknss 1/2"(12MM) 1/2"(12MM)

Cut out

4-1/4"±4-1/8"(108±3MM) 6-5/16"±6-1/8"(168±3MM)

Driver

Light

Mounting

Cuthole

BRAND FAMILY MODEL AFR4-9W AFR6-12W

CTCL-153PDH 1-16 1-12

CTCL-153P 1-16 1-12

CT-600P 1-16 1-12

DIVA DVCL-153P 1-16 1-12

6672 1-16 1-12

6674 1-16 1-12

PASS &

SEYMOUR

HARMONY HCL453PTCCCV6 1-16 1-12

Dimmer Compatibility List

for LED Recessed Lights. Dimmable down to 20%.

DECORA

SKYLARK

CONTOUR

LUTRON

LEVITON

8PL-AFR912-ES-A4

Ledpax Technology SD4-3K Installation guide

Brand: Ledpax Technology

Model: SD4-3K

Category: Dimmers

Type: Installation guide

Download PDF

report

Ledpax Technology SD4-3K Installation guide

Ledpax Technology SD4-3K Installation guide

Other documents