Aiwa TV-F2000u, TV-F2400u is a color television with a variety of features that can enhance your viewing experience. Some of the capabilities of this device include:
- High-quality picture: The TV-F2000u and TV-F2400u produce sharp, detailed images with rich colors and deep blacks. They are ideal for watching movies, TV shows, and playing video games.
- Wide viewing angle: The wide viewing angle of the TV-F2000u and TV-F2400u allows you to enjoy a clear picture even when you're not sitting directly in front of the TV. This makes them perfect for large rooms or for use in commercial settings.
Aiwa TV-F2000u, TV-F2400u is a color television with a variety of features that can enhance your viewing experience. Some of the capabilities of this device include:
- High-quality picture: The TV-F2000u and TV-F2400u produce sharp, detailed images with rich colors and deep blacks. They are ideal for watching movies, TV shows, and playing video games.
- Wide viewing angle: The wide viewing angle of the TV-F2000u and TV-F2400u allows you to enjoy a clear picture even when you're not sitting directly in front of the TV. This makes them perfect for large rooms or for use in commercial settings.
SERVICE MANUAL
DATA
COLOR TELEVISION
TV-F2000
TV-F2100
U
HT,NH
S/M Code No. 09-009-432-1S2
SUPPLEMENT
• This Service Manual contains the additional information
“DISASSEMBLY INSTRUCTIONS” and “ADJUSTMENT”
for the model TV-F2000 (U) / TV-F2100 (HT,NH).
If requiring the other information, see Service Manual of
TV-F2000(U), (S/M Code No. 09-006-432-1R1) and
TV-F2100(HT,NH), (S/M Code No. 09-008-432-1R2).
– 2 –
NOTICES BEFORE REPAIRING
• Do not turn on the power without degaussing coil when repairing.
• In case of removing degaussing coil when repairing, connect dummy as follows;
Method 1 : Use another new degaussing coil and connect it when repairing.
Method 2 : Place the 6.8Ω - 20W resistor to the degaussing coil connector and connect it as service jig.
• Cement resistor R848, which is parallel to the degaussing coil, is opened when the power is turned on without the degaussing coil or dummy resistor.
This model’s cement resistor, R848 is as shown below.
Horizontal noise will appear on the screen if this cement resistor has been opened.
• If there is no instruction for setting of the input signal, get signal from line input (LINE-IN).
Model name
TV-F2000 / F2100
R848
56Ω / 2W
Type
Cement Resistor
– 3 –
Anode cap
CRT GND
Hook
CRT
CRT GND
Grip
DISASSEMBLY INSTRUCTIONS
1. REAR CABINET REMOVAL
Figure 1-1
2. HIGH-VOLTAGE CAP (ANODE CAP) REMOVAL
2-1. Cautions before Removing
Discharge the anode voltage
(1) The anode voltage is not discharged completely from the
CRT of this unit even after the power is turned off. Be
sure to discharge the residual anode voltage before
removing the anode cap.
Do not use pliers
(2) Do not use pliers, etc. to remove the anode cap. If you
used pliers and bent the hook to remove the cap, the spring
characteristics of the hook could be lost, and when
reinstalled, the cap would come off from the CRT anode
button easily, causing an accident.
Do not turn the anode cap
(3) If the anode cap is turned in the direction of its
circumference, the hook is likely to come off.
2-2. Anode Cap Removal
Discharge the anode voltage. (See Figure 2-1)
(1) Connect a flat-bladed screwdriver to the CRT GND via
an alligator clip.
(2) Use a tester to check the end of the screwdriver and ground
of the TV for continuity.
(3) Touch the hook with the end of the screwdriver.
Caution : Be careful not to damage the anode cap.
(4) Turn over the anode cap.
Caution : Be careful not to damage the anode cap.
Figure 2-1
Figure 2-2
Anode cap
CRT
Hook
Anode button
(1) Remove four screws 1 and three screws 2 , then
remove the rear cabinet in the direction of the arrow.
(See Figure1-1)
Front cabinet
Rear cabinet
1
1
1
1
2
– 4 –
(5) Push the anode cap with your thumb in the direction of
arrow 1 as shown in the figure, then lift the cap in the
direction of arrow 2 to release the hook on one side.
(See Figure 2-3)
(6) Turn over the anode cap on the side where the hook was
released and pull out the cap in the direction opposite to
that on which the cap was pushed. (See Figure 2-4)
Caution : Do not pull out the anode cap straight up.
: Do not pull the cap forcibly. After removing
the cap, check that the hook is not deformed.
Figure 2-3
3. ANODE CAP REINSTALLTION
Observe the cautions carefully so that no accident occurs
due to a defect in installing the anode cap and so it does
not come off.
3-1. Caution before Reinstalling
Never turn the anode cap after installing it
Never re-use the hook when it has been deformed
(1) If the anode cap is turned after it is installed, it may come
off. Therefore, arrange the high-voltage cable before
attaching the anode cap. (See Figure 3-1)
(2) If you have attached the anode cap before arranging the
high-voltage cable, arrange the cable carefully so the cap
does not turn.
3-2. Anode cap reinstallation
(1) Use a clean cloth moistened slightly with alcohol to clean
the installation section. (See Figure 3-2)
Caution : Check that the installation section is free from
dust, foreign matter, etc.
(2) Coat the anode cap installation circumference with an
appropriate amount of the specified silicone grease (KS-
650N).
Caution : Be careful that silicone grease does not enter
the anode button.
CRT
CRT
Anode cap
Hook
Hook
Anode cap
Hook
Anode button
CRT
Left
Right
Anode cap
Anode button
Installation
section
Figure 2-4
Figure 3-1
Figure 3-2
– 5 –
(3) Eliminate twisting, etc. of the high-voltage cable and
arrange it so that no twisting occurs. (See Figure 3-3)
Caution : If the cable is not arranged correctly, the anode
cap could turn and cause an installation defect.
(4) Turn over the rubber cap symmetrically on the left and
right. (See Figure 3-4)
Caution : Take great care not to damage the anode cap.
Figure 3-3
(5) Fit your forefinger over the projection at the center of the
cap and hold the cap between your thumb and middle
finger. (See Figure 3-5)
High-voltage cable
Anode cap
Figure 3-4
Figure 3-5
– 6 –
(6) Apply the hook on one side to the anode button as shown
on the figure. (See Figure 3-6)
Caution : Check that the hook is held securely.
(7) Apply the hook on the other side to the anode button as
shown in Figure 3-7.
(8) Pull the anode cap slightly with the rubber cap turned
over and visually check that the hook is engaged securely.
(9) Release your hand from the rubber cap of the anode cap.
Caution : Cover the anode cap so that it does not lift.
(10) Hold the skirt of the andoe cap slightly to improve the
close contact between the cap and CRT.
(11) Check that the anode cap is in close contact with the CRT.
(See Figure 3-8)
Figure 3-8
Figure 3-7
Figure 3-6
Anode button
Skirt
Hook
Anode button
Anode button
Hook
Anode button
Hook
30°
– 7 –
Figure 4-1
4. NK C.B REMOVAL
(1) Disconnect CN903 (CRT GND).
(2) Disconnect CN901, CN902, CN951, CN952.
(3) Remove the NK C.B. in the direction of arrow 1.
(See Figure 4-1)
5. MAIN C.B REMOVAL
(1) Remove connector (CN404) from Audio C.B.
(2) Remove connector (CN807).
(3) Remove connector (CN882) from PS C.B.
(4) Pull out the MAIN C.B. in the direction of the arrow 2
(See Figure 4-1).
CN882
(Power Cord)
Front cabinet
AUDIO C.B
CN404(Speakers)
CN951
NK C.B
CN901
CN903
CN807
(Degauss
cord)
CN902
CN952
MAIN
C.B
– 8 –
Color bar signal of a pattern generator
Precautions Before Starting Adjustment
Satisfy the following setting conditions before starting adjustment.
• Allow warm-up of 20 minutes or longer. (Do not turn off during
warm-up.)
• Set all picture quality controls of users' setting to initial set-up,
unless otherwise specified.
• Picture quality reset
1. Select "Picture" on the screen menu and press enter button.
2. Select "Normal" and press enter button.
3. Select "Reset" and press enter button.
• Set the pattern generator’s output level to 1.0Vp-p (across 75Ω
load).
Because the video signal output from a pattern generator is used as
the adjustment signal input during adjustment, the video signal
output from the pattern generator must conform with the
specifications. Measure the output waveform across 75 Ω load.
Confirm that the synchronizing signal has an amplitude of about
0.3 V, the video signal portion has an amplitude of about 0.7 V and
the burst signal has an amplitude of about 0.3 V with flat envelope.
Confirm that ratio of the burst signal amplitude and the red signal
amplitude is 0.30 : 0.66. If the output signal does not conform with
the specifications, calibrate the pattern generator. (Refer to pattern
generator operation manual.)
Use the LEADER: LCG 404 for the pattern generator.
Fig. 1-1
Approx.
0.3V
Approx. 0.3V
Burst signal
1 Vp-p
White (Approx.
75%)
Approx. 0.7V
Yellow
Cyan
Green
Magenta
Red
Blue
Black
75% white
TV display
1-1. Precautions
(1) Receive the white raster signal, and then perform aging for at
least 20 minutes.
(2) Demagnetize the area surronding the CRT with a degausser
before making adjustments.
(3) Set the picture quality for each mode to the factory setting.
(4) Position the front screen facing the east as much as possible.
1-2. Purpose
(1) Beam landing adjustment (purity magnet)
Set the left/right balance of beam landing. If there is a
discrepancy in this adjustment, a color irregularity will occur.
After completion of the landing adjustment, it is necessary to
perform convergence adjustment.
Color
Color
irregularity
Color
irregularity
Before adjustment After adjustment
ADJUSTMENT
Set-Up For Adjustment 1. CRT Adjustment
– 9 –
(2) Beam convergence adjustment (4-pole magnet)
Align the R beam with the B beam. The G beam does not
move with this adjustment.
B
G
R
R/B
G
Align the R beam with the B beam
Fig. 1-2
(magenta)
(4) The composition of each magnet is as shown in Fig. 1-4.
In making adjustments, rotate the lock ring clockwise (looking
from the CRT’s back screen) and disengage.
Be careful not to loose the lock ring too much. If the magnet
assembly has become shifted during adjustments, secure it to
the position in Fig. 1-4.
(3) Beam convergence adjustment (6-pole magnet)
With a 4-pole magnet align the G beam with the already aligned
R/B beam.
G
R/B
RGB
(magenta)
(white)
Align the G beam with the R/B beam
Fig. 1-3
CRT DY
DY lock screw
Purity 4-pole 6-pole
Lock ring
NK C.B
Magnet assembly
Fig 1-4
Magnet assembly
lock screw
– 10 –
(1) Receive the green raster signal from the pattern generator.
(2) Loosen the magnet lock screw, and shift the magnet assembly
backward (toward the neck).
(3) Loosen the DY lock screw, and shift the DY deflecting yoke
backward (toward the neck).
(4) After opening the two purity magnets to the same angle, adjust
the color width of the bands on both sides of the screen so that
they are equal. (refer to Fig. 1-5 (a)).
As shown in Fig. 1-5 (b), the purity magnet functions in
relation to the electron beam.
(5) Gradually shift the deflecting yoke toward the front (toward
the CRT funnel). Stop movement at the point when the screen
has become completely green.
(6) Also, verify the respective monochromatics of red and blue.
(7) While looking at the screen, adjust the tilt of the deflecting
yoke and tighten the DY lock screw.
(8) Shift the magnet assembly to the front (toward the CRT funnel),
stop movement before the adjustment position and then tighten
the magnet lock screw.
At this time, be careful not to shift the position of the purity
magnet.
As there is occurrence of convergence distortion after
completing the landing adjustments, be sure to carry out
convergence adjustments.
If the color irregularities in the screen’s corner section are
not improved, correct them with the landing magnet. After
using the landing magnet, be sure to demagnetize the CRT
with degausser and verify that there is no occurrence of color
irregularity. (refer to Fig. 1-6)
Landing magnet: 81-JTI-710-010
(two-sided adhesive tape) : 80-XVI-218-010 Cushion
Cushion
Landing magnet
Since the landing magnet is polarized,
check the screen’s improvement through
rotation, not only by position.
Fig 1-6
1-3. Beam Landing Adjustment
RGB
Fig 1-5 (a)
R=B
SN NS
NS SN
NN
SS
SS
NN
Fig 1-5 (b)
– 11 –
Make adjustments on the convergence with 4-pole and 6-pole
magnets. Operate each magnet in relation to the electron beam as
shown in Figs. 1-7 and 1-8. When performing this adjustment, verify
whether there is distortion in the focus adjustment. If necessary,
carry out adjustments again.
BGR
SN
NS
S
S
NN
BGR
Fig 1-7
Fig 1-8
In Fig. 1-7, two 4-pole magnets are stacked together so as to be of
the same polarity. Move the B and R beams to their respective
direction, by rotating the two 4-pole magnets together. By adjusting
the opening of the two magnets, it is possible to adjust the amount
of the beam’s movement.
Perform this adjustment after completion of adjustment 1-4.
(1) Shake the deflecting yoke up, down to the right and left, and
adjust any discrepancies in the screen’s surroundings.
(2) Insert wedges in three locations in the gap between the
deflecting yoke and the surface of the CRT funnel in order
to secure the deflecting yoke. (Refer to Fig. 1-9)
Position of wedge
Fig. 1-9
Wedge
Wedge
Wedge
In Fig. 1-8, the two 6-pole magnets are stacked together so as to be
of the same polarity. Move the B and R beams to their respective
direction, by rotating the two 6-pole magnets together. By adjusting
the opening of the two magnets, it is possible to adjust the amount
of the beam’s movement.
(1) Receive the dot pattern signal from the pattern generator.
(2) Pay attention to the center of the screen, and perform
adjustments with two 4-pole magnets so that the R beam and
B beam are perfectly aligned and become a magenta color.
(Refer to Fig. 1-2)
(3) In the same way, pay attention to the screen, and perform
adjustments with a 6-pole magnet so that the magenta beam
and G beam are aligned and become a white dot.
(Refer to Fig. 1-3)
(4) After adjustments are completed, secure all magnets with the
lock link. (Refer to Fig. 1-4)
GRB
N
N
N
S
S
S
S
N
N
S
GRB
S
N
1-4. Beam Center Convergence Adjustment 1-5. The Surrounding Convergence Adjustment
– 12 –
Setting of IIC BUS Data
This model is designed with the ability to adjust most parts of the image
projection and deflection system by using the jig remote controller.
Preparations :
• Modify the hidden keys on the RC-6VT06 jig remote controller
(TV-C142/86-LB4-951-010) so that they can easily be pressed.
2 keys to be modified. (Refer to the below illustration)
Starting the “Service Mode” :
Hidden key / “TEST”
• Press the “TEST” key on the jig remote controller once to enter to the
“Aging Mode” (Refer Fig. 1).
• Press the “TEST” key on the jig remote controller again to enter the
“Adjustment Mode”.
Hidden key / “FINISH”
• The accumulated hours in the “Aging Mode” will be reset by pressing
the “FINISH” key on the jig remote controller.
• Avoid to press this key during general repairs.
Aging Mode Operation Method :
Make sure that confirmation is done after replacing the EEP ROM.
<TV-F2000>
1. Enter to the aging mode by pressing the “TEST” key on the remote
controller. (Fig. 1a)
2. Press “SYSTEM” key and confirm the condition of the distinction
switch. (Fig. 2a)
Confirm the following items before doing the electrical adjustment.
• In case the contents are different, press “1” key and select [US21]
for the destination.
• In case the data is different use the “CHANNEL” key to scroll
through 0~F and set to the correct data value of “0” or “1” by the
volume key.
• All the settings are stored when the “TEST” key is pressed to
complete the correction.
<TV-F2100>
1. Enter to the aging mode by pressing the “TEST” key on the remote
controller. (Fig. 1b)
2. Press “SYSTEM” key and confirm the condition of the distinction
switch. (Fig. 2b)
Confirm the following items before doing the electrical adjustment.
• In case the contents are different, press “3” key and select [NH21]
for the destination.
• In case the data is different use the “CHANNEL” key to scroll
through 0~F and set to the correct data value of “0” or “1” by the
volume key.
• All the settings are stored when the “TEST” key is pressed to
complete the correction.
AGING AFT OK 0000H US21
Fig. 1a
0 1 2 3 4 5 6 7 8 9 A B C D E F
1 US21
2 TW21
3 NH21
4 NH25
5 US25
6 TW25
0 1 0 1 0 1 1 1 1 1 1 1 1 1 0 0
Fig. 2a
AGING AFT OK 0000H NH21
Fig. 1b
0 1 2 3 4 5 6 7 8 9 A B C D E F
1 US21
2 TW21
3 NH21
4 NH25
5 US25
6 TW25
0 1 0 1 0 1 1 1 1 1 1 0 1 1 0 0
Fig. 2b
– 13 –
3. Display of “CRT ON” accumulated hours
The CRT usage time is accumulated on an hourly basis and is displayed in
hexadecimal figures.
Sample calculation of displayed hexadecimal figures: AFT OK 1234 H ST+S
• The display will be reset to 0000H when the accumulated hours exceed
7FFFH(32768 hours).
Contents of Aging Mode :
1. Release “Auto Power Off” function
Release “Auto Power Off” function when no input is supplied.
Use this mode for warming up (aging) during CRT adjustment.
2. AFT S-curve status indication
The condition of FT S-curves are indicated by “OK” for suitable tuning, “UP” for too high or “DN” for too low.
AFT S-curve
UP
...
Deviation from standard value high.
OK
...
Normal value.
DN
...
(DOWN) Deviation from standard value low.
– 14 –
Adjustment Mode Operation Method :
1. Return to the aging display by pressing the “SYSTEM” key and press “TEST” key to display the adjustment menu screen.
Fig.3
PAGE 1
1 H POS 00
2 V POS 00
3 V SIZE 00
4 OSD POS 00
5 PIF VCO 00
6 RF AGC 00
PAGE 2
1 R CUTOFF 00
2 G CUTOFF 00
3 B CUTOFF 00
4 G DRIVE 00
5 B DRIVE 00
ENTER CONTRAST
PAGE 3
1 SUB CONTRAST 00
2 SUB BRIGHT 00
3 SUB TINT 00
4 SUB COLOR 00
PAGE 4
1 358 TRAP 00
2 BPF 00
3 H AFC 00
4 WPL 00
PAGE 4
1 ATT 00
2 SPECTRAL 00
3 WIDEBAND 00
PUSH
1~6 KEY
PUSH
1~5 KEY
PUSH
1~4 KEY
PUSH
1~4 KEY
PUSH
1~3 KEY
PUSH
CH UP/DN KEY
PUSH
CH UP/DN KEY
PUSH
CH UP/DN KEY
PUSH
CH UP/DN KEY
PUSH
CH UP/DN KEY
H POS 0~31
V POS 0~7
V SIZE 0~63
OSD POS 0~48
SD OK
PIF VCO 58 AFT OK
RF AGC 32 SD OK
PAGE 1
R CUTOFF 0~255
G CUTOFF 0~255
B CUTOFF 0~255
G DRIVE 0~255
PAGE 2
B DRIVE 0~255
ATT 10
PAGE 5
SUB CONTR...-63~+63
PAGE 3
SUB BRIGHT -63~+63
SUB TINT -63~+63
SUB COLOR -63~+63
358 TRAP D:ON
PAGE 4
1:OFF
BPF CUTOFF 2:AUTO
0: OFF
WPL 1: ON
0: +2
H AFC 1: +1
SPECTRAL 31
WIDEBAND 31
Press "MENU"
key to return
Press "MENU"
key to return
Press "MENU"
key to return
Press "MENU"
key to return
Press "MENU"
key to return
*
Each figure in the adjustment menu can be changed using the volume adjustment keys (+, —).
*
Though the "MENU" contents will disappear once "MUTE" key were pressed while operating on "MENU" screen, it will reappear by pressing "O" key.
– 15 –
PWB Adjustment / Do before entering the adjustment mode
1. H SIZE Horizontal Size Crosshatch
Input Signal : Crosshatch
Adjustment Point : SFR601
Measuring Instrument : Pattern generator / reader : LCG-401
• Use SFR601 to adjust the dot mark of the crosshatch to the center.
(So that the number of measure become the same horizontally and vertically)
2. PIN & BARREL Pin Phase & Pin Amplitude (Barrel) Adjustment (Linearity).
Input Signal : Crosshatch
Adjustment Point : SFR602 / PIN (Fig. A)
SFR603 / BARREL (Fig. B)
Measuring Instrument : Pattern generator / reader : LCG-401
• Adjust the crosshatch distortion.
1. Use SFR602 to adjust the vertical distortion (Fig. A).
2. Use SFR603 to adjust the horizontal distortion (Fig. B).
• Repeat 1~2 until the vertical lines become straight.
Electrical adjustment:
• Operate after inputting the following initial figures when replacing EEP ROM.
• Check the condition and adjust the area where the general repair is carried out.
Initial Value
PAGE 1
1. H POS 16
2. V POS 3
3. V SIZE 30
4. OSD POS 6
5. PIF VCO 58
6. RF AGC 32
PAGE 2
1. R CUT OFF 127
2. G CUT OFF 127
3. B CUT OFF 127
4. G DRIVE 127
5. B DRIVE 127
PAGE 3
1. SUB CONTRAST – 5
2. SUB BRIGHT + 32
3. SUB TINT + 16
4. SUB COLOR + 16
PAGE 4 Specific Value
1. 3.58 TRAP OFF
2. BPF AUTO
3. H AFC + 1
4. WPL OFF
PAGE 5
1. ATT 10
2. SPECTRAL 24
3. WIDEBAND 44
6 ~ 7
6 ~ 7
Center
Fig. A
Fig. B
Crosshatch signals are not illustrated
– 16 –
PAGE 1
1-1. H POS Horizontal Positioning Adjustment / Adjustment Menu Screen : PAGE 1-1
Input Signal : Crosshatch
Measuring Instrument : Pattern generator / reader : LCG-401
• Use the volume keys on the jig remote controller to adjust the dot mark in the centre of
crosshatch screen to the exact centering position by allocating an equal number of squares
on the left and right side of the dot. (Fig. 1-1)
1-2. V POS Vertical Positioning Adjustment / Adjustment Menu Screen : PAGE 1-2
Input Signal : Crosshatch
Measuring Instrument : Pattern generator / reader : LCG-404
• Using the volume keys on the jig remote controller to adjust the
dot mark to the exact vertical centre position in the crosshatch screen.
(Fig. 1-2)
V LINEARITY Vertical Linearity Adjustment
Input Signal : Monoscope (LION MARK)
Measuring Instrument : Monoscope / NTSC
• Adjust the 6 circular figures on monoscope to be true circles by SFR501.
<Simple Adjustment>
Input Signal : Crosshatch
Adjustment Location : SFR501
Measuring Instrucment : Pattern generator / NTSC
• Adjust the SFR501 to make crosshatch patterns square.
*
Adjust V POS (PAGE 1-2) and Linearity repeatedly. If it does not work, adjust V Size
(PAGE 1-3) first and try the adjustment again.
1-3 V SIZE Vertical Size Adjustment / Adjustment Menu Screen : PAGE 1-3
Input Signal : Crosshatch
Measuring Instrument : Pattern generator / reader : LCG-401
• Use the volume keys on the jig remote controller to adjust the number of
the squares of the crosshatch pattern to 13~14. (Fig. 1-3)
PAGE 1
V POS
18
13 ~ 14
Squares
CRT center
mark
PAGE 1
V POS 2
Fig. 1-1
Fig. 1-2
Fig. 1-3
PAGE 1
H POS 20
8~9 8~9
Center
– 17 –
1-4. OSD POS OSD Positioning Adjustment / Adjustment Menu Screen : PAGE 1-4
Input Signal : Not specified.
• Use the volume keys on the jig remote controller to adjust the position of the + sign
on both right and left sides shown on the OSD screen to be equivalent from the
screen edge. A=B Fig. 1-4
1-5. PIF VCO Video IF/ VCO Adjustment / Adjustment Menu Screen : PAGE 1-5
Input Signal : ANT RF-INPUT
Colour Bar
Measuring Instrument: Pattern generator / reader : LCG-404
• Use the volume keys on the jig remote controller to adjust the status of AFT on the
screen to “OK”. Fig. 1-5
• If “OK” status can be obtained from multiple numbers of ranges, select the
intermediate value.
* SD will display “NG” while the screen has no signals. There will be no problem with
VCO Adjustment (e.g. when there is no signal with Video input). In this case, it is
possible to make adjustments as long as ANT is loaded.
1-6. RF AGC RF-AGC/ Adjustment Menu Screen : PAGE 1-6
Input Signal : ANT RF-INPUT
Color Bar
Test Point : TP101 RF AGC
Measuring Instrument : Oscilloscope
Pattern generator / reader : LCG-401
1. Connect the oscilloscope to TP101.
2. Using the volume keys on the jig remote controller to adjust the test point voltage
value to 4.0 ± 0.5VDC. Then check if the status of AFT on the Adjustment Menu
Screen is displayed “OK” as shown in Fig. 1-6.
PIF
VCO
58
SD
AFT
OK
OK
PAGE 1
PAGE 1
RF
AGC
32
AFT
OK
Fig. 1-4
Fig. 1-5
Fig. 1-6
PAGE 1
OSD POS 24
+
AB
+
– 18 –
PAGE 2
White Balance Adjustment : Adjustment Menu Screen : PAGE 2-1~5
*User’s picture quality will be cleared when the adjustment menu screen appears.
Input signal : White raster
Contents of Adjustment : 1. R CUT OFF
Contents of Adjustment : 2. G CUT OFF
Contents of Adjustment : 3. B CUT OFF
Contents of Adjustment : 4. G DRIVE * More than 20 minutes of aging is required
5. B DRIVE before the adjustment.
Contents of Adjustment * The whole process should be repeated
several times for the adjustment.
Measuring instrument : Pattern generator / reader : LCG-401
Cut Off Adjustment :
2-1. Use the pattern generator to input the white raster signal.
2-2. Using the volume keys on the jig remote controller, fix the figure of the strongest color on the screen to 127 and adjust the other 2 cut off
figures until white picture appears on the screen.
Drive Adjustment :
2-3. Using the volume keys on the jig remote controller, bring the figure of the 4.G DRIVE up to more than 200 till the color becomes greenish.
2-4. Then reduce the numeric figure to the point where the greenish color disappears completely.
2-5. Using the volume keys on the jig remote controller, bring the figure of the 5.B DRIVE up to more than 200 till the color becomes bluish.
2-6. Then reduce the numeric figure to the point where the bluish color disappears completely.
2-7. Repeat the process of 1~6 for several times and adjust for whiter look.
Focus Adjustment :
Input Signal : Dot pattern
Adjustment Point : SFR located at upper part of FBT (T601)
Measuring Instrument : Pattern generator / reader : LCG-401
• Adjust SFR which is located at upper part of FBT (T601) in order to get the best focus for
the dot.
Screen Adjustment :
Input Signal : No Signal (No Raster)
Adjustment Point : SFR located at lower part of FBT (T601)
Measuring Instrument : Pattern generator / reader : LCG-401
1. Enter to “Aging Mode Screen” by pressing “TEST” key on the jig remote controller once.
2. Press “10” key of the numeric channal keypad to get a horizontal single line screen (Fig.2-2).
3. Adjust SFR located at lower part of FBT (T601) until the horizontal line starts to be slightly brightened.
4. Repeat the process of step 2 and return to the “Adjustment Menu Screen”.
PAGE 3
3-1. SUB BRIGHT Sub-brightness Adjustment / Adjustment Menu Screen : PAGE 3-2
(careful with the order)
Input Signal : Color Bar (Stair step)
Measuring Instrument : Pattern generator / reader : LCG-401
• Using the volume keys on the jig remote controller to adjust the scale of the second last
from right to be slightly brightened.
R CUTOFF 0~255
G CUTOFF 0~255
B CUTOFF 0~255
G DRIVE 0~255
PAGE 2
B DRIVE 0~255
R CUTOFF 127
G CUTOFF 127
B CUTOFF 127
G DRIVE 127
PAGE 2
B DRIVE 127
Fig. 2-2
PAGE 2
35
SUB BRIGHT
Fig. 3-1
Fig. 2-1
– 19 –
3-2. SUB CONTRAST Sub-contrast Adjustment / Adjustment Menu
Screen : PAGE 3-1
Input Signal : Color Bar (QIW)
chroma/OFF
Measuring Instrument :Oscilloscope
Pattern generator / reader : LCG-401
Test Point : S0901 R(R CATHODE)
1. Connect the oscilloscope to S0901 R.
2. Using the volume keys on the jig remote controller adjust
the pedestal level and the voltage of 100% white to 95 ± 2V,
according to Fig. 3-2.
3-3. SUB TINT Sub-Tint Adjustment / Adjustment Menu Screen : PAGE 3-3
Input Signal : Color Bar (VIDEO IN)
Measuring Instrument :Oscilloscope
Pattern generator / reader : LCG-401
Test Point : CNA704 3 PIN B
1. Connect the oscilloscope to CNA704 3 PIN B .
2. Using the volume keys on the jig remote controller, adjust the top
excursions of waveform “Magenta” and “Blue” to be linear
(Fig. 3-3).
3-4. SUB COLOR Sub-color Adjustment / Adjustment Menu Screen : PAGE 3-4
Input Signal : Color Bar (VIDEO IN)
Measuring Instrument :Oscilloscope
Pattern generator / reader : LCG-401
Test Point: CNA704 3 PIN B
1. Connect the oscilloscope to CNA704 3 PIN B .
2. Using the volume keys on the jig remote controller, adjust the top
excursions of waveform to be linear (Fig. 3-4).
PAGE 4
4. TV SETTING CHECK Confirmation of Model Setting / Adjustment Menu Screen : PAGE 4-1~4
Each setting is particular to each model. Do not make any changes to these fixed setting.
• Check if the details of the Adjustment Menu Screen are the same as those in Fig. 4.
If they were different, readjust them accordingly using the volume keys on the jig remote
controller.
95 ± 2V
100% White
75% White
Pedestral Level
Magenta
Blue
Fig. 3-2
Fig. 3-3
Fig. 3-4
Fig. 4
* The details of 3.58 TRAP cannot be controlled.
3.58 TRAP 0 : ON
BPF 2 : AUTO
H AFC 1 : +1
WPL 0 : OFF
– 20 –
PAGE 5
5-1. ATT ALIGNMENT ATT Adjustment / Adjustment Menu Screen : PAGE 5-1
Input Signal : ANT RF-INPUT / Color Bar
Measuring Instrument : Oscilloscope
Pattern generator / reader : LCG-401
Test Point: IC701 2 PIN TV OUT-L
1. Connect the oscilloscope to IC701 2 PIN
2. Using the volume keys on the jig remote controller, adjust the value of IC701 2 PIN
to 490 ± 20mVrms.
5-2. SEPARATION ALIGNMENT Adjustment of Stereo Sound Separation
Degree/Adjustment Menu Screen : PAGE 5-2~3
Input Signal: Setting of TV Multiplex Transmission Signaler
Multiplex Transmission Signaler RF Output / 2CH
Measuring Instrument :Oscilloscope
TV Multiplex Transmission Signaler / reader : 236A
Test Point: IC701 1 PIN TV OUT-R
1. Connect the oscilloscope to IC701 1 PIN
2. Start receiving signals from TV 2CH.
3. PAGE 5-3
Using the volume keys on the jig remote controller, adjust the voltage width
of IC701 1 PIN waveform to the minimum as in Fig 5-3.
4. PAGE 5-2
Adjust the internal Variation of TV Multiplex Transmission Signaler to
1kHz and perfrom the same method as in step 3. (Fig 5-4)
5. Repeat the step 3~4 for several times to adjust for the minimum value.
Fig. 5-3
PAG E 5
10
AT T
Variation Internal
Internal Variation 400 Hz
Audio L ch
Channel 2 ch
Video Signal Color Bar
Minimum
0.2V
0.5mS
Fig. 5-1
Fig. 5-2
Fig. 5-4
WIDEBAND
PAGE 5
31
SPECTRAL
PAGE 5
31
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Aiwa TV-F2000 User manual
- Type
- User manual
- This manual is also suitable for
Aiwa TV-F2000u, TV-F2400u is a color television with a variety of features that can enhance your viewing experience. Some of the capabilities of this device include:
- High-quality picture: The TV-F2000u and TV-F2400u produce sharp, detailed images with rich colors and deep blacks. They are ideal for watching movies, TV shows, and playing video games.
- Wide viewing angle: The wide viewing angle of the TV-F2000u and TV-F2400u allows you to enjoy a clear picture even when you're not sitting directly in front of the TV. This makes them perfect for large rooms or for use in commercial settings.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Panasonic TX47P500H Operating instructions
-
DeLOCK 91646 Datasheet
-
-
-
LG Electronics 30FZ4D User manual
-
Hitachi C43-FD5000 User manual
-
akira CT-25NI9AN User manual
-
-
Toshiba 50A60 User manual
-
Sony KDP-65WS550 User manual