Homestyles 4512-95 Operating instructions

Brand: Homestyles

Model: 4512-95

Type: Operating instructions

451 -952

Kitchen Cart

Adjustable Pin

8 pcs. (+1 extra)

M4x25

Machine Screw

5 pcs.

Knob

5 pcs.

M3x16

Wood Screw

for Magnet

4 pcs. (+1 extra)

M x253

Wood Screw (long)

24 pcs. (+1 extra)

M x253

Flat Head Screw

3 pcs. (+1 extra)

M x163

Wood Screw (short)

24 pcs. (+1 extra)

Hex Wrench

1 pc.

M6x12

Head Cap Bolt

for Caster

16 pcs. (+1 extra)

M6x25

Head Cap Bolt

4 pcs. (+1 extra)

M6x38

Head Cap Bolt (long)

4 pcs. (+1 extra)

Magnet

2 pcs.

Top

1 pc.

Side Panel

1 pc.

Back Panel

3 pcs.

Middle Panel

1 pc.

Back Rail

1 pc.

Back Upright

2 pcs.

Rack Side

1 pc.

Rack Side

1 pc.

Rack Bar

1 pc.

Rack Base

1 pc.

Base

1 pc.

Arm

2 pcs.

Towel Bar

1 pc.

Shelf

2 pcs.

Door

1 pc.

Door

1 pc.

Drawer

3 pcs.

Front Rail

2 pcs.

Refer to later page(s) of these

instructions for drawer assembly.

Side Panel

1 pc.

Back Rail

1 pc.

Front Rail

1 pc.

Caster

2 Locking

2 Non-Locking

4 pcs.

Small

Hex Wrench

1 pc.

IMPORTANT

Hardware List

Part List

Tool(s) required for assembly: Phillips screwdriver

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

styles Customer Service: www.homestylesfurniture.com,home

[email protected],

888-680-7460

Assembly Instructions 2/7

IMPORTANT

 Use a soft cloth between these parts and the ﬂoor.

 Do not use power tools above 8 volts to assemble.

 Do not tighten all the bolts until each part is properly assembled.

 Keep Hex Wrench as the bolts may need to be tightened in the future.

STEP 1

Assemble Rack Sides (M), (N), Rack Base (O) and Rack Bar (P).

STEP 2

Attach unit to Side Panel (C) with Head Cap Bolts.

Head Cap Bolt

STEP 3

Attach Arms (K) to Side Panel (B) with Head Cap Bolts.

Head Cap Bolt

Assembly Instructions 3/7

Lock

Figure 1

Figure 2

STEP 4

Attach Back Rail (G)

to Side Panel (C),

then ﬂip Locks.

(See Figures 1 and 2)

Attach Back Uprights (F)

to unit.

Slide Back Panels (E)

into position.

Attach Back Rail (H)

to unit, then ﬂip Lock.

Attach Side Panel (B)

to unit, then ﬂip Locks.

Figure 3

STEP 5

Attach Base (J) to unit with

Head Cap Bolts (long), then ﬂip Locks.

(See Figure 3)

Note: Arrow label indicates front of Base (J).

Arrow label at front

Head Cap Bolt (long)

Lock

Assembly Instructions 4/7

Figure 4

STEP 6

Attach Casters to unit with Head Cap Bolts

for Caster into pre-drilled holes

with Locking Casters at front.

(See Figure 4)

Note: Arrow label indicates front of unit.

Wood Screw for Magnet

Magnet

STEP 7

Attach Magnets to Front Rail (W)

by inserting Wood Screws for Magnet

into pre-drilled holes, then tighten.

(See Figure 5)

Figure 5

Arrow label at front

Head Cap Bolt for Caster

Non-Locking Caster

Locking Caster

Assembly Instructions 5/7

STEP 9

Insert Wood Screws (short)

into pre-drilled holes in unit,

then tighten.

Slide Towel Bar (L) into position.

STEP 8

Turn unit over to its

upright position.

Attach Middle Panel (D)

to unit, then ﬂip Locks.

Attach Front Rails (I), (W)

to unit, then ﬂip Locks.

Wood Screw (short)

Lock

Part List

T2.

Drawer Back

3 pcs.

T5.

Drawer Bottom

3 pcs.

T1.

Drawer Front

3 pcs.

T3.

Drawer Side

3 pcs.

T4.

Drawer Side

3 pcs.

STEP 12

Attach Knob with Machine Screw.

Drawer (T)

Wood Screw (short)

Roller at back

Bottom

STEP 10

Attach Drawer Front (T1) and Drawer

Back (T2) to Drawer Side (T3)

with Wood Screws (long).

Attach Drawer Side (T4) to unit

with Wood Screws (long).

Wood Screw (long)

Machine Screw

Knob

STEP 11

Slide Drawer Bottom (T5) into groove.

Attach Drawer Bottom (T5) to unit

with Wood Screws (short).

Assembly Instructions 6/7

Assembly Instructions 7/7

STEP 13

Insert Adjustable Pins into

side panel and middle panel

at desired level.

(See Figure )6

Place Shelves (S) into position.

Attach Doors (Q) and (R)

by sliding door hinges

into side panel and

middle panel hinges.

(See Figure )7

Attach Knobs to Doors (Q)

and (R) with Machine Screws.

(See Figure )8

Figure 6

Figure 7

Figure 8

STEP 14

Attach Top (A) to unit

with Flat Head Screws, then ﬂip Locks.

Slide Drawers (T) into position.

Machine Screw

Knob

Adjustable Pin

Flat Head Screw

Lock

NEVER

use glass cleaners on

finished furniture. Ammonia

chemically attacks the finish.

allow liquids to remain on furniture.

Absorption causes parts to warp

and split and finishes to delaminate.

NEVER

CARE INSTRUCTIONS

Do not use rubber

based placemats.

PREVENT

DISCOLORING

Do not use commercial

waxes and polishes.

PREVENT

YELLOWING

Do not place hot

objects on surface.

PREVENT

FINISH DAMAGE

Do not write

directly on surface.

PREVENT

MARKING

Do not use power tools

above 8 volts to assemble.

PREVENT

CRACKING

Do not place

in direct sunlight.

PREVENT

FADING

with a soft cloth moistened

in lukewarm soap and water.

Buff with a dry clean cloth.

CLEAN

homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.

Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,

homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor

are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.

styles Customer Service: www.homestylesfurniture.com,home

[email protected],

888-680-7460

Homestyles 4512-95 Operating instructions

Homestyles 4512-95 Operating instructions

Homestyles 4512-95 Operating instructions

Related papers

Other documents