2
3
1. Do not operate any fan with a damaged cord or plug. Discard fan or return to
an authorized service facility for examination and/or repair.
2. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area
and where it will not be tripped over.
3. Fan should be used under rated voltage.
4. Connect power after the fan is fully assembled.
5. Never insert fingers, pencils, or any other object through the guard when fan is running.
6. Unplug from outlet when not in use, when moving fan from one location to another, before putting
on or taking off parts, and before cleaning.
7. Disconnect fan when removing grilles for cleaning.
8. Be sure fan is on a stable surface when operating to avoid overturning.
9. DO NOT use fan in window, rain may create electrical hazard.
RULES FOR SAFETY OPERATION
ASSEMBLY INSTRUCTIONS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt
to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 10 minutes
Fig. 2
1. Pull power cord (E) out slightly.
2. Put front base (B) onto rear base (C) and join them together.
3. Put the round base on the body (A) by inserting the cylinders under
(A) to blind holes on the round base as shown on diagram.
4. Fix (A) with base clip (D) as shown.
A
B
C
E
D
OPERATING INSTRUCTIONS (Fig. 3)
Fig. 3
CARE AND MAINTENANCE
• Always unplug the fan before cleaning.
• Do not allow water and steam to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline, paint thinner, benzine.
• Periodically clean this fan by lightly running a vacuum cleaner nozzle over the fan
grilles to remove any dust or dirt that may have accumulated inside or on the unit.
• Wipe all parts with a soft cloth.
• Dry all parts completely before reassembling or reconnecting the fan to the wall outlet.
• Keep surfaces dry and clean for a longer-lasting finish.
Proble
TROUBLESHOOTING
m Possible Cause Corrective Action
The fan will not
operate.
The fan isn’t plugged in and/or the
electrical outlet isn’t working properly.
Make sure the fan is plugged in and/or
the electrical outlet is working properly.
The fan will not
operate.
Obstructions stop the fan from working. Check for obstructions. If you find an
obstruction, turn the fan off.
Unplug the fan and carefully remove the
obstruction. Plug the fan in and turn it
on again by referring to the operating
instructions.
INSERT BATTERIES (Fig. 4)
Fig. 4
Notes:
.
ICON FUNCTION
Power
Speed Setting
Wind Mode
Timer
Oscillating
DETAIL
Press this key to turn the fan on/off
Press this key to desired fan speed,
1 = Low, 2 = Medium, 3 = High
Press this key to desired wind mode in the
sequence of NORMAL-BREEZE ( ) -SLEEP ( )
Press this key repeatedly to set the timer
from 1 hour to 8 hours
Press this key to start or stop the fan oscillation
1. Grasp plug and remove from the wall outlet.
Do not unplug by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attached
plug toward blades.
3. Remove fuse carefully. Push the fuse from the other side or turn
fuseholder over to remove fuse.
4. Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
5. Close fuse cover. Slide closed the fuse access cover on top of attached plug.
6. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be
removed. Discard product if the attached plug is damaged.
WARNING: This appliance has a polarized plug (one blade is wider than the other). The polarized
plug is not intended to be used in non-polarized outlets (having both slots the same size). To reduce
the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug, if it still does not fit, contact a qualified electrician. Do not
modify the plug in any way.
USER SERVICING INSTRUCTIONS
Battery
Compartment Cover
Batteries
Remote Control
1. Press down on the battery compartment cover and slide it out.
2. Insert the batteries, making sure that the positive terminals are facing
the proper direction marked inside the battery compartment.
3. Close the cover by sliding it in.
1) Use 2 “AAA” batteries (NOT INCLUDED).
2) Do not mix old and new batteries.
3) Do not mix alkaline, standard (carbon-line) or rechargeable
(nickel-cadmium) batteries.