EXPERT GRILL Concord-Gas Griddle User manual

Brand: EXPERT GRILL

Model: Concord-Gas Griddle

Category: Barbecues & grills

Type: User manual

EXPERT GRILL Concord-Gas Griddle boasts a spacious cooking surface, ideal for preparing large meals for family and friends. Its powerful burners deliver precise temperature control for searing steaks, grilling vegetables, or creating fluffy pancakes. Cleanup is a breeze with the removable grease tray, making it easy to maintain a pristine cooking environment. Enjoy the convenience of gas grilling with the safety features like flame observation aperture and overfilling prevention device, ensuring a safe and enjoyable grilling experience.

• Parts

• Assembly

• Safety Rules

• Use and Care

• Troubleshooting

Description:

Expert Grill Concord-Gas Griddle

Model: XG1136224169004

Read this Owner’s manual carefully and be sure your

gas grill is properly assembled, installed and

maintained. Failure to follow these instructions could

result in serious injury and/or property damage.

For Outdoor Use Only

Owner's Manual

Important: Keep this Owner’s Manual for

convenient reference and for part replacement.

If you have any questions or problems, you can

contact our customer service at 855-256-2160 or

expertgrill@grillservices.net from 8 AM – 4:30

PM Eastern Time, Monday to Friday.

Please make sure the cylinder valve connection

device shall properly and safely mate with the

connection device attached to the inlet of the

pressure regulator.

Safety Precautions

WARNING

Combustion by products produced when using this product contain chemicals known to the

State of California to cause cancer, birth defects, or other reproductive harm.

WARNING

Failure to comply with these instructions could result in a fire or explosion that could cause

serious bodily injury, death, or property damage.

WARNING

Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch

cooking surfaces, grill housing, hood or any other grill parts while the grill is in operation, or

until the gas grill has cooled down after use.

Failure to comply with these instructions may result in serious bodily injury.

WARNING

1. Do not store or use gasoline or

other flammable liquids or

vapors in the vicinity of this or

any other appliance.

2. An LP gas cylinder not

connected for use shall not be

stored in the vicinity of this or

any other appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open hood.

4. If odor continues, keep away

from the appliance and

immediately call your fire

department.

READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THE APPLIANCE

SAVE THESE INSTRUCTIONS

WARNING

Remove the POP labels before using the grill.

WARNING:

If the outdoor cooking gas appliance is not in use, the gas must be turned off at the supply

cylinder(s). Storage of an outdoor cooking gas appliance indoors is permissible only if the

cylinder(s) is (are) disconnected and removed from the outdoor cooking gas appliance.

Cylinders must be stored outdoors out of the reach of children and must not be stored in a

building, garage or any other enclosed area.

• Let your LP gas cylinders be filled by reputable

propane gas distributors and visually inspected

and recertified each time you fill.

1) do not store a spare LP gas cylinder under or

near this appliance; 2) never fill the cylinder

beyond 80 percent full; and 3) if the instructions

in (1) and (2) are not followed exactly, a fire

causing death or serious injury may occur.

• Always keep the LP cylinder in an upright position.

• Do not allow the liquefied petroleum gas cylinder

to overheat.

• Never store liquefied petroleum gas cylinders

indoors. If you store the gas grill in a garage or

other indoor location, be sure to disconnect the

LP cylinder and store it safely outdoors.

• Place dust cap on cylinder valve outlet whenever

the cylinder is not in use. Only install the type of

dust cap on the cylinder valve outlet that is

provided with the cylinder valve. Other types of

caps or plugs may result in leakage of propane.

• LP gas cylinders must be stored outdoors in a

well-ventilated area and out of reach of children.

Disconnected LP gas cylinders must not be

stored in a building, garage or any other enclosed

area.

• When your gas grill is not in use the gas must be

turned off at the LP gas cylinder.

• The pressure regulator and hose assembly must

be inspected before each use of the grill. If there

is excessive abrasion or wear or if the hose is cut,

it must be replaced prior to the grill being used

again. Replacement pressure regulators and

hose assemblies shall be those specified by the

appliance manufacturer.

• Keep the gas regulator hose away from hot grill

surfaces and dripping grease. Avoid unnecessary

twisting of hose. Visually inspect the hose prior to

each use for cuts, cracks, excessive wear or

other damage. If the hose appears damaged do

not use the gas grill. Call 855-256-2160 for

assistance.

• Never light your gas grill with the hood closed or

before checking to ensure the burner tubes are

fully seated over the gas valve orifices.

• Never allow children to operate your grill.

• If the above instructions are not strictly followed,

a fire that may result in death or serious injury

may occur.

Provided with a listed overfilling prevention

device.

This safety feature prevents the gas cylinder from

being overfilled which can cause malfunction of the

LP gas cylinder , regulator and/or grill.

The LP gas cylinder must be constructed and

marked in accordance with specifications of the U.S.

Dept. of Transportation (DOT). In Canada, the LP

gas cylinder must meet the National Standard of

Canada, Can CSA –B339, Cylinders, spheres and

Tubes for Transportation of Dangerous Goods and

Commission .

1. The LP gas cylinder must have a shutoff valve,

terminating in an LP gas supply cylinder valve outlet,

that is compatible with a Type 1 cylinder connection

device. The LP cylinder must also have a safety

relief device that has a direct connection with the

vapor space of the cylinder.

2. Always keep LP gas cylinder in an upright position.

The cylinder supply system must be arranged for

vapor withdraw.

3. The LP gas cylinder used must have a collar to

protect the cylinder valve.

Proper Placement and Clearance of Grill

This outdoor cooking gas appliance shall be used

only outdoors and shall not be used in a building,

garage, or any other enclosed area., at least 2FT

from the back and side of any combustible surface.

Your gas grill should not be used under overhead

combustible construction. Do not obstruct the flow of

ventilation air around the gas grill housing.

• Do not install this outdoor gas grill in or on

recreational vehicles or boats.

• Keep outdoor gas grill area clear and free from

combustible materials, gasoline and other flammable

vapors and liquids.

• Do not obstruct the flow of combustion and

ventilation air. Check for this each time prior to using

grill.

• Never connect an unregulated LP gas cylinder to

your gas grill. The gas regulator assembly supplied

with your gas grill is adjusted to have an outlet

pressure of 11” water column (W.C.) for connection

to an LP gas cylinder.

• Only use the regulator and the hose assembly

supplied with your gas grill. Replacement regulators

and hose assemblies must be those specified in this

manual.

Safety Precautions

WARNING

A strong gas smell, or the hissing sound of gas

indicates a serious problem with your gas grill or

the LP gas cylinder. Failure to immediately follow

the steps listed below could result in a fire or

explosion that could cause serious bodily injury,

death, or property damage.

• Shut off gas supply to the gas grill.

• Turn the control knobs to OFF position.

• Put out any flame with a proper fire

extinguisher.

• Open Grill Hood.

• Get away from the LP gas cylinder.

• Do not try to fix the problem yourself.

• If odor continues or you have a fire you can not

extinguish, call your fire department. Do not call

near the LP gas cylinder because your telephone

is a form of electrical device and could create a

spark resulting in fire and/or explosion.

CAUTION: Spiders and small insects occasionally

spin webs or make nests in the grill burner tubes

during transit and warehousing. These webs can lead

to gas flow obstruction which could result in a fire in

and around burner tubes. This type of fire is known as

“FLASH-BACK” and can cause serious damage to

your grill and create an unsafe operating condition for

the user.

Although an obstructed burner tube is not the only

cause of “FLASH-BACK”, it is the most common

cause.

To reduce the chance of “FLASH-BACK”, you must

clean the burner tubes before assembling your grill,

and at least once a month in late summer or early fall

when spiders are most active. Also perform this burner

tube cleaning procedure if your grill has not been used

for an extended period of time.

See Cleaning Burner Tubes and Ports on page # 24.

NOTE: The normal flow of gas through the

regulator and hose assembly can create a

humming noise. A low volume of noise is perfectly

normal and will not interfere with operation of the

grill. If humming noise is loud and excessive you

may need to purge air from the gas line or reset

the regulator excess gas flow device. This purging

procedure should be done every time a new LP

gas cylinder is connected to your grill. For help with

this procedure refer to page 22, “If Grill Still Fails

To Light”, or call the Customer Service Helpline 8

AM to 4:30 PM Eastern Time at: 855-256-2160

Visually check the burner flames prior to each

use. The flames should look like picture, if they

do not, refer to the cleaning burner tubes and

ports, see page 24 of this manual.

Requiring the grill can be connected to the gas

supply by means of a flexible hose connector

complying with the current Standard.

for Elastomeric Composite Hose and Couplings

for Conducting Propane and Natural Gas,

CAN/CGA-8.1or with the Standard for

Thermoplastic Hose and Hose Couplings for

Conducting Propane and Natural Gas, CAN1-8.3.

CAUTION: Beware of Flash-Back

Burner Flame Check

WARNING

Keeping the ventilation opening(s) of the

cylinder enclosure free and clear from debris.

From the firebox observe the flame burning

flame observation aperture steady state

WARNING

Spiders and insects can nest inside the

burners of the grill and disrupt gas flow. This

very dangerous condition could cause a fire

behind the valve panel, thereby damaging the

grill and making it unsafe for operation.

Inspect the grill at least twice a year.

Safety Precautions ----------------------------------2-4

Burner Flame Check---------------------------------- 4

Expert Grill Concord Model Description---------- 6

Hardware ------------------------------------------------ 6

Tools Required for Assembly------------------------ 6

Parts Diagram------------------------------------------- 7

Parts List----------------------------------------------- 8-9

Assembly Steps -----------------------------------10-19

Connecting LP Gas cylinder to LP Grill ----- 20-21

Grill Lighting Instructions ----------------------- 21-22

Cooking Instruction -----------------------------------23

Cleaning and Seasoning --------------------------- 23

Cleaning and Maintenance--------------------- 24-25

Troubleshooting----------------------------------------25

Notes on electrical appliances -------------------- 26

Warranty ------------------------------------------------ 26

Customer Service------------------------------------- 27

Table of Contents

Hardware

Tools Required for Assembly

Philips Head Screwdriver (not included)

X30

A B

Expert Grill Concord Model Description

The rated power of each main grill is 11000BTU;

Grill burners are not installed with cross-illumination channels between each adjacent burner;

All burners are operated by separate plug-type gas valves;

All burner controls are installed in the control panel of the appliance. The control valve is operated

by a coated plastic control knob. The upper cover is connected to the stainless handle with rubber

sleeve by two Bakelite brackets;

The cooking surface is an iron plate (SPHC);

The grill is equipped with an aluminum-plated mild steel heat shield to isolate the heat between the

combustion chamber and the control panel;

There is a cylinder hook on the left side of the mobile device, and only 20-pound refillable cylinders

can be used. The diameter of the LP gas cylinder is about 12-1 / 4 inches, and the height is 17-15

/ 6 inches.

On the right side of the mobile device is the pellet furnace section.

Parts Diagram

Parts List

Assembly Steps

Parts Required:

• Left Front Leg (Part #10) x1

• Left Rear Leg (Part #9) x1

• Locking Caster (Part #11) x2

Installation:

• Insert Locking Caster (Part

#11) stem into bottom of Left

Front Leg (Part #10). Press into

hole until click is felt. Ensure

caster is secure and cannot

easily back out.

• Repeat for Left Rear Leg (Part

#9).

Parts Required:

• Firebox Body (Part #1) x1

• Left Front Leg (Part #10) x1

• Left Rear Leg (Part #9) x1

Installation:

• Insert the Left Front Leg (Part

#10) and Left Rear Leg (Part #9)

into Firebox Body (Part #1).

Hardware Required:

• (Hardware B) x8

• (Hardware C) x4

Installation:

• Lock Left Front Leg (Part #10)

and Left Rear Leg (Part #9).

• Use 8 screws (Hardware B) and

4 washers (Hardware C).

Note: The washers concave side

down when install.

Parts Required:

• Firebox Body (Part #1) x1

• Right Rear Leg (Part #16) x1

• Right Front Leg (Part #15) x1

Installation:

• Insert the Right Rear Leg (Part #16)

and Right Front Leg (Part #15) into

Firebox Body (Part #1).

Parts / Hardware Required:

• (Hardware B) x4

• Bottom Shelf (Part #12) x1

Installation:

• Attach Bottom Shelf (Part #12) to

legs using 4 screws (Hardware B)

from underside of shelf.

Hardware Required:

• (Hardware B) x4

• (Hardware C) x4

Installation:

• Lock Right Rear Leg (Part #16)

and Right Front Leg (Part #15).

• Use 4 screws (Hardware B) and 4

washers (Hardware C).

Note: The washers concave side

down when install.

Parts / Hardware Required:

• (Hardware A) x1

• Wheel Axle (Part #14) x1

• Wheel (Part #13) x2

Installation:

• Upright grill with help from an

additional person.

• Insert Wheel Axle (Part #14)

through Wheel (Part #13) and

Leg (Part #15), Leg (Part #16).

• Place R Pin (Hardware A) onto

Wheel Axle.

Hardware Required:

• (Hardware B) x2

Installation:

• Open the Hood

• Lock Right Rear Leg (Part

#16) and Right Front Leg

(Part #15).

• Use 2 screws (Hardware B).

Parts / Hardware Required:

• (Hardware B) x4

• Connecting Board of Gas Cylinder

Hook (Part #7) x1

Installation:

• Mount Connecting Board of Gas

Cylinder Hook (Part #7).

• Use 4 screws (Hardware B).

Note: the part which have 2 screws

face upward!

Parts / Hardware Required:

• (Hardware D) x4

• Hood Handle (Part #3) x2

Installation:

• Open the Hood

• Mount Hood Handle (Part #3).

• Use 4 screws (Hardware D).

Parts / Hardware Required:

• (Hardware B) x2

• Gas Cylinder Hook (Part #6) x1

Installation:

• Mount Gas Cylinder Hook (Part

#6).

• Use 2 screws (Hardware B).

Parts / Hardware Required:

• (Hardware B) x2

• Baffle of Cylinder and Strap (Part

#5) x1

Installation:

• Mount Baffle of Cylinder and

Strap (Part #5).

• Use 2 screws (Hardware B).

Parts / Hardware Required:

• (Hardware B) x4

• Side Shelf (Part #2) x1

Installation:

• Pre-thread in the 2 screws

(Hardware B) with 0.2 inch of

thread exposed.

• Hang Side Shelf (Part #2) on

2 screws (Hardware B).Tighten

preinstalled screws.

• Insert 2 screws (Hardware B)

in remain.

Parts Required:

• Grease Tray (Part #17) x1

Installation:

• Mount Grease Tray (Part

#17).

Parts Required:

• Ash Clean-out Cover (Part #8) x1

Installation:

• There are two ears on the back

side of Ash Clean-out Cover (Part

#8).

• Put this cover into the hole, with

2 ears at orientation shown, then

turn 90 degree as shown.

Parts Required:

• Flame Tamer (Part #18) x1

Installation:

• Place Flame Tamer (Part #18)

over Fire pot. Locate using 3

Holes.

Parts Required:

• Grease Drain Pan (Part #19) x1

Installation:

• Mount Grease Drain Pan (Part

#19) on the firebox. The tab should

be placed as shown.

Parts Required:

• Searing Station Pull Handle (Part

#22) x1

Installation:

• Insert Searing Station Pull Handle

(Part #22) through grommet on side

of firebox assembly.

• Align the flat end to the slot as

shown. Press it into when Daisy

Wheel is open.

• Turn the handle 90 degree as

shown to lock well.

Quick cooking food with pushing the

handle to open the Daisy Wheel .

Normal cooking when pulling the

handle out to close the Daisy Wheel.

Parts Required:

• Cooking Griddle (Part #4) x1

• Grease Tray (Part #23) x1

• Cooking Grid (Part #20) x2

• Warming Rack (Part #21) x2

Parts / Hardware Required:

• Power Cord Bracket (Part #24)

• (Hardware E) x2

Installation:

• Insert Power Cord Bracket

(Part #24) through slots in

backside of Hopper Assembly

•Insert screw (Hardware E)

through hole and tighten.

1. Please hang a 20lb LP gas cylinder on the hook of

the gas cylinder on the right side of the oven, and

fasten it with the gas cylinder strap (Fig.2).

2. Check the cylinder valve to ensure it has proper

external mating threads to fit the hose and regulator

assembly provided.

3. Make sure all burner valves are in OFF position.

4. Inspect the valve connection port and regulator

assembly. Look for damage or debris. Remove any

debris. Inspect hose for damage. Never use

damaged or plugged equipment.

5. When connecting regulator and hose assembly to

cylinder valve hand tighten quick coupling nut

clockwise to a full stop (Fig.1). Do not use a wrench

to tighten because it could damage the quick

coupling nut and result in a hazardous condition.

6. Open cylinder valve fully (counterclockwise). Use

a soapy water solution to check all connections for

leaks before attempting to light your grill. If a leak is

found, turn cylinder valve off and do not use your grill

until the leak is repaired.

CAUTION: When the appliance is not in use, gas

must be turned off at the supply cylinder.

Regulator Connection

Figure 1

Congratulations

Your gas grill is now ready for use. Before the

first use and at the beginning of each season

(and whenever the LP gas cylinder has been

changed):

1. Read all safety, lighting and operating

instructions.

2. Check gas valve orifices, burner tubes and

burner ports for any obstructions.

3. Perform gas leak check according to

instructions found on next page of the manual.

Remove the gas cylinder from the grill

1. Make sure that the cylinder valve is in the closed position.

2. Make sure that all burner valves are in the closed position.

3. Open the cylinder strap.

4. When removing the regulator and hose assembly from the cylinder valve, loosen the quick

connection nut counterclockwise by hand, do not tighten it with a wrench, as this may damage the

quick connection nut and cause a dangerous situation.

Figure 2

Connecting LP Gas cylinder to LP Grill

Page is loading ...

EXPERT GRILL Concord-Gas Griddle User manual

Brand: EXPERT GRILL

Model: Concord-Gas Griddle

Category: Barbecues & grills

Type: User manual

Download PDF

report

EXPERT GRILL Concord-Gas Griddle User manual

EXPERT GRILL Concord-Gas Griddle User manual

Related papers

Other documents