Page is loading ...
Maxim Edger
Tool Tips
Operation & Safety
ME4HWT
Safety Practices:
Application: Edging and light trenching
DO NOT operate the unit without
reading and understanding
owner’s manual. Failure to learn
operation instructions and safety
procedures could result in
equipment or property damage,
personal injury or death.
DO NOT operate the unit under
the influence of alcohol, drugs or
while taking medication that
impairs the senses or reactions.
Before starting the engine
Step
1 Check Edger. Be sure all bolts are tight.
2 Check oil and fill according to the engine owner’s manual
Make sure all guards are in place and you know how to
stop the machine and disengage blade.
3
Starting the engine
Step
Move fuel valve lever to the
on position.
1
DO NOT allow unauthorized or
untrained people to operate the
unit. Improper use of the
equipment may cause serious
injury or death.
To start a cold engine, move
the choke lever to the
closed position. To restart a
warm engine, leave the
choke lever in the OPEN
position.
2
DO NOT wear loose clothing while
operating the unit. Always wear
safety glasses and appropriate
safety equipment.
Keep hands, feet and other body
parts away from moving or
rotating parts of the unit.
DO NOT operate the unit with
faulty brake mechanism or with
out safety guards, shields or
covers.
DO NOT operate indoors or in an
area with poor ventilation. This
engine emits toxic carbon
monoxide.
DO NOT fuel while the engine is
running.
DO NOT overfill the fuel tank.
After refueling, make sure the
tank cap is closed properly and
securely.
Move the throttle lever to
the mid point position on
either the engine or the
cross bar of the edger.
3
Turn the engine switch to
the on position
4
Pull the starter grip lightly until you feel resistance, then
pull briskly in the direction of the arrow as shown below.
Return the starter grip gently.
5
Step
Shut Down instructions
Move the throttle on the cross brace to the minimum or off
position.
1
2 Turn the engine switch to the OFF position
Operation instructions:
Action
Step
Decide which blade configuration is appropriate for your
application. For edging, only one blade is needed.
Remove one blade and a spacer for greater efficiency.
1
DO NOT smoke or allow open
flames or sparks during refueling.
For shallow trenching for invisible pet fencing or low
voltage wire, use two star blades with the spacer.
2
Edging depth is set with the blade control lever. When
edging an area for the first time it may be desirable to set
the depth lower to establish a trench for the blade for
future edging.
© MTA Distributors of TN & KY, Inc. All rights reserved. 2008
ME4HWT
3
YARD RENTS
Maxim Edger
ME4HWT
Operating Instructions:
• Push machine to the desired location.
• Remove any rocks or debris along the edging path.
• Make sure all shields are in place and that the blade points
rotate forward as shown in the picture at left.
• Position wheels of machine on sidewalk or other solid surface
or lawn.
• Crank the machine.
• Lower the blade into the ground using blade control lever to
your desired edging depth.
• When edging in a new area for the first time you will need to
stop and remove debris as it is pulled from the ground. After
a few edgings you will find your work quicker and smoother.
• Pull the edger slowly backwards around the drive, sidewalk,
or landscaping feature giving the edger time to make a
complete cut.
• Do not try to edge too quickly.
• Watch carefully for bystanders and pets.
•
WARNING:
• Never operate the edger without proper guards, shields or
other safety devices in place. Serious injury or death could
result.
Questions or Problems:
• Even though this edger is equipped with safety shields, it is
possible for debris to be thrown from the edger. Wear safety
glasses at all times and keep the edger area clear of
bystanders, especially small children and pets.
Contact the store listed on your
rental contract.
Need more information?
•
Do not attempt to start or operate this edger until you are
completely familiar with the location and use of each control
necessary to operate this edger. You must know how to stop
this machine before you start it.
The instructions on this sheet are
abbreviated instructions only and
are provided solely as a customer
service. They are not meant to
replace the tool’s operation
manual. If you are unsure of the
tool’s safe and proper operation,
please request an operator’s
manual from one of the store
sales associates.
• Stay clear of the front of the machine during and after
starting. Once machine is started, stand behind it with hands
on the handles at all times.
• Thoroughly inspect the area where the edger is to be used
and remove all the large stones, boards, wires, and other
foreign objects.
• Do not operate the edger in wet, muddy soil, which clogs the
cutter and increases your danger of falling.
• Do not operate machine while barefoot or while wearing open
sandals. Wear strong work-type footwear, which will improve
footing and provide optimum foot protection.
WARNING: Using this product
for a purpose not intended may
cause property damage, serious
injury or death.
• Stay alert for hidden hazards or traffic.
• Never place hands, feet, or any part of body or clothing near
any moving part of this edger.
• If edger should start to vibrate abnormally, stop the engine
and check for the cause. Vibration is generally a warning of
trouble or damaged blade.
© MTA Distributors of TN & KY, Inc. All rights reserved. 2008
ME4HWT
/
