Standing Fan
F22SC / F22C
PRODUCT CODE
ASSEMBLY
Screws
Plastic Screw Nut
Fan Blades
Cap
Oscillation Knob
Power Cord
Locking Knob
Tilt Control Bolt
Tube Cover
Inner Tube
Base
Steadying Plate
Height Adjustment Knob
Nut Slice
Bolt
Knob
Screw
Rotary Switch
1.4.
Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065
www.eurolux.co.za
Please read instructions before commencing installation and retain for future reference.
IMPORTANT:
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid a
hazard.
Ensure that the fan is switched off from the supply mains before removing the guard.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
This marking indicates that this product should not be disposed with other household wastes thoughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
Fan Assembly:
1. Ensure that the power is disconnected.
2. Remove any protective plastic.
3. Position the rear grill guard over the motor shaft, ensuring that the notches are correctly aligned and
then x into place with the screws / plastic nut provided.
4. Align the fan blades with the at part on the motor shaft and secure into position with the plastic cap.
5. Position the front grill guard and secure into place with the clips / screws provided.
Stand Assembly:
1. Insert the pole into the base and put the xed circle and the steadying plate under the base, using the
bolt and nut slice provided to tighten.
2. Unscrew the height adjustment knob, and pull up the inner tube to adjust the height, ensuring that the
knob is fully tightened before proceeding.
3. Position the fan head motor either side and insert the tilt control bolt into the square hole of the
coupling and lower into the inner tube.
Tighten the small screw that is already located in the coupling and then t the knob onto the tilt
control bolt and lightly tighten.
4. Insert the locking knob through the top hole of the coupling adjusting the fan head to the
desired position and rmly tighten screw and the tilt control.
FS22SC / FS22C - attachments:
If the external exible cable or cord of this fan is damaged, it should be exclusively replaced by the
manufacturer or his service agent or a similar qualied person in order to avoid a hazard.
To ensure that you get maximum longevity and maximum use out of your fan, please observe the
following safety instructions.
Electrical products can cause death, injury, or damage to property.
Installation of the fan must be carried out by a qualied electrician, in accordance
with SANS 10142. On completion of installation, ensure that the Certicate of Compliance
is updated.
• Before connecting this fan, ensure that voltage indicated on the rating label corresponds with the
mains voltage in your home.
• When cleaning, ensure that the power is turned off.
• This fan is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons,
caused by the incorrect use or installation of the fan.
• Should you be unsure of how to install this fan correctly, please consult a professional electrician
or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT SAFEGUARDS ASSEMBLY INSTRUCTIONS:
• Ensure the fan is in the off position when plugged in.
• Adjust the fan speed by moving the rotary switch from:
0: Off
I: Low
II: Medium
III: High
• To oscillate, press down the control knob at the top of the motor housing. To lock position,
pull up on the same knob.
• To adjust the angle of the fan, loosen large tilt control knob and smaller locking screw, then adjust
the fan head to the desired position and retighten.
• Use the height adjustment knob on the stem of the fan to raise or lower the fan as
detailed above.
OPERATION:
CLEANING
• Before cleaning always ensure the power supply is turned off and that the fan has
been unplugged.
• Do not immerse the fan in water.
• No abrasive products, solvents, detergent may be used to clean this fan.
• Ensure that the fan does not come in contact with corrosive chemicals, etc.
• Remove the front grill guard, blades and rear grill guard and wipe down parts with a damp cloth
to remove any dust.
• Ensure all parts are dry before reassembling your fan.
• The motor bearings are permanently sealed and do not require additional lubrication
• Fitting material: Steel.
• Motor: 50W.
• Voltage: 220 - 240V~ 50Hz.
• Protection against electric shock: Class I. Requires earth connection.
• IP: 20. Protected against solid foreign objects of 12.5mm Ø and greater.
• Not for outdoor use or in wet conditions and areas of high humidity.
• Dimensions: (H)1190mm x (W) 450mm x (D)430mm.
• Features: 3 Speeds.
Lockable direction.
Adjustable tilt and height adjustable up to 1190mm.
Including: cable & plug.
SPECIFICATIONS
2. 3.
/
