Rain-Flo Rain-Flo 2370 Flat Bed Plastic Mulch Layer User manual

Brand
Rain-Flo
Model
Rain-Flo 2370 Flat Bed Plastic Mulch Layer
Category
Holders
Type
User manual

This manual is also suitable for

MODEL 2370
FLAT BED PLASTIC MULCH LAYER
OPERATING
MANUAL
1
Table Of Contents
Cover Disk ............................................................. 5
Dirt Shield .............................................................. 5
Drip Pipe ................................................................ 6
Drip Roll ................................................................. 6
Features ................................................................ 2
Helpful Tips ..........................................................13
Options .................................................................. 2
Parts Breakdown, Descriptions ......................10-12
Parts Breakdown, Exploded Views .....................7-9
Plastic Roll, Installing............................................. 3
Plastic Tension ....................................................... 3
Plastic Width .......................................................... 4
Press Wheel .......................................................... 4
Safety First ............................................................ 2
Swing Arm ............................................................. 6
Trench Opener ......................................................5
Trouble Shooting .................................................14
Warranty ..............................................................13
2
Make sure you read and understand all the precautions.
Keep people away when lifting and lowering the machine.
Be careful when turning around; machine is 6’ long.
Do not crawl under the machine when lifted.
Cover discs are sharp; stay clear.
Do not adjust the machine when it is moving.
Do not stand on machine.
Tractor operator is responsible for extra worker(s) around machine.
Rain-Flo Irrigation is not responsible for accidents if any should
occur.
!
!
!
!
!
!
!
!! Safety First !!
!
!
* Optional Depth Wheels (For Sweet Corn)
* Optional Double or Single Drip Applicator
• The Model 2370 Flat Bed Mulch Layer
will lay 3’, 4’ or 5’ Wide Plastic
• Extra Plastic Roll Carrier
• 16” Cover Disks with Dirt Shields
• Compact Machine; Category I 3-Point Hitch
• Lays Clear Plastic over Sweet Corn
• Adjustable Row Markers
• Adjustable Brake Tension on Plastic Roll Carriers
• Independent Disk & Press Wheels
• Quality Powder Coated Baked-On Paint
Features
Options
Adjusting Plastic Tension
Plastic rolls have a tension brake. Just a slight tension is needed.
Plastic Roll
Brake
Tension
Adjustment
Note; Setting brake tension too tight on plastic roll may affect
the performance of the machine and can also cause plastic to
pull out from under press wheels.
Installing Plastic Rolls
Place plastic rolls on top of rollers (A). Pull end of plastic
down and underneath the bottom roller (B). Secure plastic
and drip tape at end of row.
AA
BB
Plastic
Roll
End ViEw
Spare
Roll
Bottom Roller Plastic
Feed plastic
rolls like this
3
Press Wheel Adjustment
To stretch plastic more or less, turn axles to change the angle of the
press wheels; make in or out adjustment as needed. Press wheels
need to run at the bottom of the trench and not on the side.
Use only high quality plastic to avoid straight line tear.
Press
Wheel
Adjustment
Setting
Changing Plastic Width
1
2
Loosen bolts (No. 1) and slide trench openers and roll holders so plastic
roll ts between brackets. Adjust approximately 1½” wider than plastic
width to compensate for the roll’s core.
Remove(for 3’) or add(for 5’) roller extensions (No. 2) to make desired
width.
(No.1) Loosen 4 bolts on each side
to slide assemblies.
(No.2) Remove (for 3’ plastic) or
add roll (for 5’ plastic).
Install
Below
For 5’
Plastic
4
Model 2370 will lay 3’, 4’, or 5’ wide plastic.
Trench Opener Adjustment
Trench openers are to cut a trench along the sides of the bed. This
will give a ‘cup’ at the edge of the bed for disk to cover the plastic.
Depth
Setting
Trench Trench
OpenerOpener
IMPORTANT!
Adjust machine so that 5” of plastic is covered on both sides
Plastic
5”
Plastic
“Cup”
5”
Cover Disk & Dirt Shield Adj.
Cover disks and dirt shields are marked right and left side (standing in
back of machine). Install shields as marked (with ‘T’ handle towards the
center of the bed.) Set disk on a 45 degree angle then make in or out ad-
justment as needed.
For more coverage, bolt disk on opposite side of upright shank and turn
it around for a backward tilt.
Dirt Shield Left
to Right Setting
Left to Right Disk Setting
Disk Angle Adjustment
Dirt Shield Angle
Adjustment
Adjust trench
openers 3”
lower than
bed press
pan.
5
6
Drip Irrigation Roll Carrier
Drip Line
Down Pipe
To avoid damaging drip tape with the press pan, adjust top of down
pipe about 1” to 2” below the plastic mulch. Cut off drip lines approxi-
mately one foot longer than the rows for connecting to the water sup-
ply. Keep dirt out of the drip tape by tying a knot at the end. Drip line
can be tied to back of machine when transporting.
Drip Tape
Roller
Guides
NOTICE:
Make sure
drip roll
is com-
pressed
rmly
between
plates for
positive
braking
effect.
Slide drip roll onto roll carrier rod so that drip emitter will be turned
up toward plastic (for less clogging).
Feed drip tape through the guide on the swing arm and through
the second guide that’s bolted on the drip roll carrier frame. (See
sketch above.)
7
Plastic Mulch
Flo
Layer
Rain
-
2370
Serial
Numbers
Firm
Pressed
P
l
a
s
t
ic
W
i
d
th
Roller Extension
588
156
714
43
571
533
76
530-70L
528-70L
36
35
40
34
524
526-70L
529B-L
54
58
93
192L
94
54
525
32
7
54
13
70
532
9
41
76
525
533
532
54
54
538
37
76
76
19
452
Depth Wheel
(#50, 53, 54,452)
#464
53
54
50
418
395
578
579
#580
Depth Wheel Complete
(#395, 418, 464, 578, 579)
581
582
End View of
Plastic Roll Holders
585
Spare
Roll Holder
586
150
Operating Instructions
Operating Instructions
Operating Instructions
587 584
Double Bottom Drip Attach
(#19, 83, 516 - thru - #518)
#515D
Plastic Mulch
Flo
Layer
Rain
-
2370
Serial
Numbers
Firm
Pressed
P
l
a
s
t
ic
w
i
d
t
h
Roller Extention
588
156
518
Complete Bottom Drip Attach
(#19, 83, 516 -thru- #518)
#515A
517B
517A
120
521
18
520
120
A
d
d
We
i
g
ht
193
Rain-Flo
Irrigation
When Quality counts
583
155
201
19
516
19
83
582
581
Complete Top
Drip Roll Carrier
#1A
#1D
Complete Double
Top Drip Roll Carrier
Figure 1
2370
11
3B
3E
3A
8B
10
3D
22
54
10
7
72A
9
72A
2
1
885
89
89
885
3-P
5A
8
8F
8E
8E
8C
49
150
6B
427
192
150
148
150
192
427
8C
19
8
6C
6
3C
Figure 2
2370
146
48B-23R
529-70L
530-70R
48C-23
Plastic Mulch
Flo
Layer
Rain
-
2370
Serial
Numbers
Firm
Pressed
P
l
a
s
t
ic
W
i
d
th
Roller Extension
588
156
714
43
571
533
76
530-70L
528-70L
36
35
40
34
524
526-70L
529B-L
54
58
93
192L
94
54
525
32
7
54
13
70
532
9
41
76
525
533
532
54
54
538
37
76
76
19
452
Depth Wheel
(#50, 53, 54,452)
#464
53
54
50
418
395
578
579
#580
Depth Wheel Complete
(#395, 418, 464, 578, 579)
581
582
End View of
Plastic Roll Holders
585
Spare
Roll Holder
586
150
Operating Instructions
Operating Instructions
Operating Instructions
587 584
Double Bottom Drip Attach
(#19, 83, 516 - thru - #518)
#515D
Plastic Mulch
Flo
Layer
Rain
-
2370
Serial
Numbers
Firm
Pressed
P
l
a
s
t
ic
w
i
d
t
h
Roller Extention
588
156
518
Complete Bottom Drip Attach
(#19, 83, 516 -thru- #518)
#515A
517B
517A
120
521
18
520
120
A
d
d
We
i
g
ht
193
Rain-Flo
Irrigation
When Quality counts
583
155
201
19
516
19
83
582
581
Complete Top
Drip Roll Carrier
#1A
#1D
Complete Double
Top Drip Roll Carrier
Figure 1
2370
11
3B
3E
3A
8B
10
3D
22
54
10
7
72A
9
72A
2
1
885
89
89
885
3-P
5A
8
8F
8E
8E
8C
49
150
6B
427
192
150
148
150
192
427
8C
19
8
6C
6
3C
Figure 2
2370
146
48B-23R
529-70L
530-70R
48C-23
8
9
Figure 3
2370
111386
#66-70CR
#50
Complete Wheel Only
(#50 - 54, BB-1)
50
53
54
1
54
62
67
68
63A
R
i
gh
t
Si
d
e
173R
BB-1
47-70
111386
48-70R
57-23R
65-70R
65A-70
60-70A
12BP
42-70R
3411
12514
12SN
34SN
370
370
12612
38134
34214
70
150
Hub Complete w/ Bolts
#71
62A
62B
67 62
68
334
422
423
69-70
69-70
66
358
309A
34SN
12SN
406
148
#542-70CR
Press Wheel Complete
(#1, 42-70R,
50, 53, 54, 72)
Dirt Shield Complete
(#60-70A, 66, 69-70,
69A, 70, 128BP, 309A,
358)
#548-70CR
Complete Disc Assembly
(#47-70, 48-70R, 48B-70R,
48L-70, 57-70R, 61, 62, 63,
65-70R, 65A-70, 111386)
48S-70R
48S
48BF
48BB
65LB
65SB
150
P
l
a
s
t
ic
W
i
d
t
h
156
48B-23R
48C-23
54
430
12BP
309A
48SB
10
Item # DescrIptIon
Model 2370 Flat Bed Layer
1...................(9) ................Tee Handle
1A. ....................................Complete Single Top Drip Roll Carrier
1D .....................................Complete Double Top Drip Roll Carrier
2........................................Roll Carrier Clamp
3A ..................................... Drip Attach Adjustable Brake Tension Plate
3B ..................................... Drip Attach Brake Plate
3C ..................................... Drip Attach -- Mounting for Brake Plate
3D .....................................Drip Attach Brake Tension Plate Rotation Stop
3E .....................................Drip Attach Teon Brake Washer
3-P ...............(2) ................Drip Roll Side Plates
5A ..................................... ⅜” x ½” Set Screw
6........................................Drip Roll Carrier Frame (Single or Double)
6B ..................................... Drip Attach Arm to Guide Drip Tape
6C ..................................... Drip Attach Arm to Guide Drip Tape [Double Drip]
7........................................1” SAE Washer
8........................................Swing Arm
8B ..................................... Drip Attach Brake Tension Spring for 1” Rod
8C ................ (2) ................Drip Attach Arm U-Bolt ⅜” x 2” x 6½”
8E ................(2) ................Drip Attach Arm Plastic Roller
8F .....................................Drip Attach Arm U-Bolt Plate Only
9...................(7) ................Cotter Pin [⅛”]
10......................................Drip Roll Shaft
11 .................(3) ................ Rubber Brake Assembly
12BP ............(4) ................½” x 1½” Bent Pin
12SN ...........(2) ................½” Zinc Stover Nut
13......................................Straight Grease Zerk
19...................(8) ..................
½” Flange Nut
20...................(3) ..................
5/16” x ¾” Carriage Bolt
22.................(3) ................5/16” x 1” Thumb Screw
32.................(8) ................½” x 4” Carriage Bolt
34. ...............(2) ................Plastic Mulch Support Roll
35.................(2) ................Roll Holder Rod
36......................................Tension Tee Handle
37......................................Tension Plate
40.................(2) ................3/16” x 2” Roll Pin
41.................(4) ................UHMW Bushing
47-70. ..........(2) ................Chain Shackle Complete
48-70L. .............................Rear Cover Disk Arm (Left Side)
48-70R..............................Rear Cover Disk Arm (Right Side)
48B-23L. ..........................Left Side Back Clamp For Disc Arm Swivel Bracket
48B-23R. .......................... Right Side Back Clamp For Disc Arm Swivel Bracket
48C-23.........(2) ................Front Clamp For Disc Arm Swivel Bracket
48SB. ...........(2) ................Bushing For Swivel Bracket; 1¼” OD x ¾” ID x 5.97”
50.................(2) ................Press Wheel Tire (#50 -thru- #54)
53.................(2) ................Hub Cap
54................(13) ...............Cotter Pin
57-23L. .............................Left Side Disk Hub Mounting Bracket
57-23R..............................Right Side Disk Hub Mounting Bracket
11
Item # DescrIptIon
Model 2370 Flat Bed Layer
58.................(4) ................Cotter Pin
60-70A. .......(2) ................Dirt Shield Support Arm
62A ............. (4) ................205KR3 Bearing
66. ...............(2) ................Dirt Shield
66-70CL ........................... Left Side Dirt Shield Complete
66-70CR ........................... Right Side Dirt Shield Complete
67.................(2) ................¾” x 4½” Hub Center Bolt
68................(10) ...............⅜” x 1½” Button Socket Cap Bolt
69-70 ...........(2) ................Dirt Shield Bracket
69A .............. (2) ................Dirt Shield Flat Plate Bracket
70.................(6) ................⅜” x 1¼” Bolt
72.................(3) ................¼” x 90° Grease Zerk
72A ................................... ¼” NFT 45° Grease Zerk
76.................(6) ................UHMW Bushing (Bottom Roller)
83.................(2) ................½” x 4¼” Bolt
89.................(3) ................¼” x ¾” Carriage Head Bolt
92L. ..................................Left Side Row Marker
92R ................................... Right Side Row Marker
93.................(2) ................Row Marker Extension
94.................(2) ................Row Marker Spring
95.................(2) ................Row Marker Hinge Pin
120...............(4) ................½” x 1½” Hex Bolt
133...............(2) ................⅜” x 1½” Bolt
146..............(10) ...............½” Hex Nut
148...............(2) ................⅜” Nylon Lock Nut
150...............(2) ................⅜” Flange Nut
155....................................Rain-Flo Oval Logo Label
156....................................Plastic Width Label
168....................................Notice Label on Drip Attach
168A ................................. “Turn Drippers Up For Less Clogging” Label
169....................................Direction Arrow for Drip Attach
169A ................................. Drip Attach Brake Adjustment Plate Label
172L ................................. Left Side Standing in Back Label For Disk
172R ................................. Right Side Standing in Back Label For Disk
173L ................................. Left Side Standing in Back Label For Dirt Shield
173R ................................ Right Side Standing in Back Label For Dirt Shield
185...............(2) ................This Side Up Label
192...............(4) ................⅜” Flat Washer
193...............(4) ................½” Flat Washer
195...............(3) ................5/16” Flange Nut
201...............(2) ................½” x 3¼” Bolt
309A ............ (2) ................Safety Pin for ½” Pin
334...............(2) ................¾” SAE Washer
369...............(2) ................½” x 2¾” Bolt
395...............(8) ................⅜” x 2¾” Bolt
418...............(8) ................⅝” x 1½” Set Screw
422...............(2) ................¾” Hex Nut
423...............(2) ................¾” Lock Washer
12
Model 2370 Flat Bed Layer
427..............(30) ...............⅜” Nut
428..............(30) ...............⅜” Lock Washer
430...............(2) ................16” Disk Blade; 6 Bolt
452...............(2) ................Tire, Axle and Stem
464...............(2) ................Depth Wheel Complete [#452 -thru- 458]
515....................................Bottom Drip Square Bar
515A ................................. Complete Single Bottom Drip Attach
515D .................................Complete Double Bottom Drip Attach
516...............(4) ................½” x 1½” Set Screw
517A ................................. Bottom Drip Bolt Mounting
517B ............ (2) ................Bottom Drip Pipe Holder Bracket
518....................................Bottom Drip Pipe
519...............(2) ................CAT I Lifting Pin [Farmex]
520....................................Leveling Pan
521....................................Bed Press
524...............(2) ................Trench Opener
525...............(2) ................Safety Pin
526-70L ............................ Left Side Trench Opener Bracket
526-70R............................Right Side Trench Opener Bracket
528-70L ............................ Left Side Bottom Roll Holder Bracket
528-70R............................Right Side Bottom Roll Holder Bracket
529-70L ............................ Left Side Plastic Roll Holder
529-70R............................Right Side Plastic Roll Holder
529B-L ............................. Left Side Bolt-On Spare Roll Holder
529B-R ............................. Right Side Bolt-On Spare Roll Holder
530-70L ............................ Left Side Bottom Roller Holder
530-70R............................Right Side Bottom Roller Holder
532...............(2) ................Row Marker Pins
533...............(2) ................3’- 4’- 5’ Adjustment Roller
538....................................Plastic Roll Brake Tension Spring & Washers
542-70CL ......................... Left Side Press Wheel Complete
542-70CR ......................... Right Side Press Wheel Complete
548-70CL ......................... Left Side Complete Disk Assembly
548-70CR ......................... Right Side Complete Disk Assembly
571....................................Long Bottom Roller
578...............(2) ................Depth Wheel Bracket with Tubing
579...............(2) ................Depth Wheel Holder Plate
580...............(2) ................Optional Depth Wheel Set Complete (2 Pcs)
581....................................Serial Number Label
582....................................Firm Pressed Bed Label
583....................................Add More Weight Label
584...............(2) ................Side Decal Label
585...............(2) ................Plastic Roll End View Label
586...............(2) ................Spare Roll Label
587...............(2) ................Operating Instructions Label
588....................................Plastic 5’ Width Roller Label
3411 .............(2) ................¾” x 11” Gr. 5 Zinc Hex Bolt
12514...........(2) ................½” x 5¼” Gr. 5 Zinc Hex Bolt
12612...........(4) ................½” x 6½” Gr. 5 Zinc Hex Bolt
34214...........(2) ................¾” x 3¼” Gr. 5 Zinc Hex Bolt
38134...........(2) ................⅜” x 1¾” Gr. 5 Zinc Hex Bolt
111386 ......... (4) ................13” Turnbuckle; 1⅛” ACME Thread
BB-1 ............ (4) ................Sealed Ball Bearing
Item # DescrIptIon
13
Helpful Tips
* Adding weight will help make a rmer bed.
* Adjust 3-point top link on tractor to level machine.
* Moisture in soil is important to build nice square
beds.
* Stretching plastic in length and side to side, will
help plastic from blowing off. (See Page 3 & 4)
* Work up soil at least 6” deep.
* Periodically check for shallow spots in bed; hollow
bed will effect planting and hinder plant growth.
* Trench openers should not be set too deep; this may
prevent the machine’s full weight from resting on the
press pan and making a rm bed.
All Rain-Flo mulch layers have a two year warranty against defects
in material and workmanship.
If any part is found defective, return the defective part with the
Serial No. of the machine. If Rain-Flo nds it defective, it will be
repaired or replaced at no charge.
Call Customer Service at (717) 445-3000.
Warranty
Machine tends to drift sideways causing press
wheels to come off the plastic.
*Use sway bars on tractor 3-point hitch.
Cover disk not getting enough soil to cover edge
of plastic.
*Bolt disk on opposite side of upright shank and
turn it around for a backward tilt.
Plastic not staying under press wheel.
*Tension too tight on plastic roll carrier.
Not rm beds and shallow spots in center.
*Soil not tilled deep enough.
*Add weight on bed press.
*Top link too short.
14
TROUBLE SHOOTING
1.
2.
3.
4.
PROBLEM:
SOLUTION:
PROBLEM:
SOLUTION:
PROBLEM:
SOLUTION:
PROBLEM:
SOLUTION:
Rain-Flo Irrigation
(717) 445-3000
~2021 Edition~
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Rain-Flo Rain-Flo 2370 Flat Bed Plastic Mulch Layer User manual

Brand
Rain-Flo
Model
Rain-Flo 2370 Flat Bed Plastic Mulch Layer
Category
Holders
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents