SMARTBOARD FSE-410 Installation guide

Brand
SMARTBOARD
Model
FSE-410
Type
Installation guide
Printed in: NL PN: 1034169 Rev 02
X
12
A
B
88 in-lb (10 Nm)
τ
(×4)
#2
S3 S5 S4
(×2)
A (×16) B (×10) J (×4) K (4×)
L (×4) M (×4) N (×4)
S5
8×
A
B
4×
92.4 lb. – 200 lb.
(42 kg – 91 kg)
A (×8)
SBID-6000S & SBID-7000R
–
10 11
Max 6" (15 cm)
65" £ X £ 86"
(163 cm £ X £ 219 cm)
SMART Electric Height-Adjustable Floor Stand
FSE-410 (Model S410-1) and FSE-420 (Model S420-1)
2 1034169 Rev 02
B (×2)
S3
65
3 4
A
A
B
B
4 ×
(×2)
B (×4)
S5
S3
A (×8) 88 in-lb
(10 Nm)
τ
1034169 Rev 02 3
SBID-6000S
SBID-7000R
SBID-XXXX
–
–
8
9
(×4)
B (×4)
7
S3
10
14
13
16
4 1034169 Rev 02
SBID-6000S SBID-7000R
WM-SBID-200
SBID-6000S & SBID-7000R
Use corresponding holes as shown.
Utilisez les trous correspondants
comme indiqué.
#2
L (×4) M (×4) N (×4)
S5
10
11
4×
97 – 177 in-lb
(11 – 20 Nm)
τ
Use corresponding slots as shown.
Utilisez les emplacements
correspondants comme indiqué.
88 in-lb
(10 Nm)
τ88 in-lb
(10 Nm)
τ
L
M
N
1034169 Rev 02 5
Center display on bracket as shown.
Center l'ecran sur le support mural comme indique.
Secure the display to the wall plate by tightening the locking screws with a
Phillips No. 2 screw driver until the screws contact the wall plate.
Fixez l'écran à la plaque murale en serrant les vis de verrouillage à l'aide d'un tournevis
Phillips No. 2 jusqu'à ce que les vis touchent la plaque murale.
12
13
6 1034169 Rev 02
15
Use corresponding holes as shown.
Utilisez les trous correspondants comme indiqué.
X
14
J (×2) K (×2)
S5
Max
Min
92.4 lb. 200 lb.
(42 kg) (91 kg)
SBID-XXXX
Max 6"
(15 cm)
65" £ X £ 86"
(163 cm £ X £ 219 cm)
7 1034169 Rev 02
97 – 177 in-lb
(11 – 20 Nm)
τ
17 18
16
4×
2×
S5
J (×2) K (×2)
A B
smarttech.com/kb/171620
Press and hold the control
switch for 5 seconds.
The stand moves up and
down 3/8" (1 cm).
The stand is ready for use
or has been reset.
3/8"
(10 mm)
5 sec
< 1 sec < 1 sec
19
Press the , , and buttons
in sequence
© 2020 SMART Technologies ULC. All rights reserved. SMART Board, smarttech, the SMART logo and all SMART taglines are trademarks or
registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. All third-party products and company names may be
trademarks of their respective owners. Contents are subject to change without notice. This product and/or use thereof covered by one or more of
the following U.S. patents; smarttech.com/patents. Other patents pending. Aug 10, 2020
support.smarttech.com/support
support.smarttech.com/contact-support
FCC
Suppliers Declaration of Conformity 47 CFR § 2.1077 Compliance Information • Unique Identifier: S410-1 or S420-1
Responsible Party – U.S. Contact Information: SMART Technologies Inc. 2401 Fourth Ave., Suite 300, Seattle, WA 98121 • Mail. to: [email protected]
FCC Compliance statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Innovation, Science and Economic Development Canada (ISED)
This device complies with ICES-003 of the ISED rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Cet appareil est conforme à la norme ISED NBM-003 pour les appareils radio agréés.
Son fonctionnement est sujet aux deux conditions suivantes:
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
WARNING
Risk of Electric Shock, Fire and Injury. Review the Assembly Instructions to confirm that the appropriate critical
components and accessories are being used with this stand.
The power bar is a critical component: the supplied power bar must be a 6 outlet power bar, identified as Model
TPL615B. This model number is molded into the cover on the bottom of the power bar. This is the only approved
power bar for this unit.
The wall bracket, WM-SBID-200 (Model W200-1), is a critical component. It is required for use with the SBID-6000S
and SBID-7000R series displays. This is the only approved mounting bracket for use with this unit.
AVERTISSEMENT
Risque de choc électrique, d'incendie et de blessure. Consultez les instructions de assemblage pour confirmer que
les composants et accessoires critiques appropriés sont utilisés avec ce stand.
La barre d'alimentation est un composant critique: la barre d'alimentation fournie doit être une barre d'alimentation
à 6 prises, identifiée comme le modèle TPL615B. Ce numéro de modèle est moulé dans le couvercle au bas de la
barre d'alimentation. Il s'agit de la seule barre d'alimentation approuvée pour cet unite.
Le support mural WM-SBID-200 (modèle W200-1) est un composant critique. Il est nécessaire pour une utilisation
avec les écrans des séries SBID-6000S et SBID-7000R. Il s'agit du seul support de montage approuvé à utiliser
avec cet unite.
Was this document helpful? smarttech.com/docfeedback/171620
smarttech.com/fse400troubleshoot
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

SMARTBOARD FSE-410 Installation guide

Brand
SMARTBOARD
Model
FSE-410
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents