Becken PLACA INDUCAO 4 ZONAS IF7017 Owner's manual

Brand: Becken

Model: PLACA INDUCAO 4 ZONAS IF7017

Type: Owner's manual

IF-7017

1500

IF-7017

COLORQ'tyCODE

BLUE

RED

RED/150mm

RED/450mm

303206800036

303206800041

303206800157

303206800158

303206800159

YELLOW/GREEN

IF-7017

180 Coil groupware

303203501117 4

Ceramic plate

bracket

sponge strip I

sponge strip II

Code

590×11×5mm

490×11×5mm

Q'ty

SGCC T=0.8

303208101074 the ceramic plate temperature sensor 3

Screw

301500100954 SJ2821/ST4*10-PFH

516

radiator board

541400300003 1

554*484*13.3mm AL1060

power board

303203101364 2

301500101200 Screw+gasket M4*35-PFH 1

junction port holder

303207801038 PBT 660VAC 1

303207300216 Base 1

FR-PP

303203601114 Power Cord 1

5*1.5mm*1800mm

303207300213

FR-PP

FR-PP 1

303207300214 power cord case cover

303207300215 windshield insulating flake 1

225*33*11mm T0.5mm FR-PC

accessorial power

303203101365

301500101194 Screw 12

SJ2828/M4x8-PFH

303207300212 line clamp 8

nylon

303207300211 knighthead nylon

303207103155 isinglass flake A 327*60*0.3mm 3

303203101374 Display board 285*55mm 1

Specification

Description

303207800275 Bracket 2

303207103156 isinglass flake B 448*380*0.3mm 1

303208003019 Fan 15V/0.3~0.8A/2100~3000rpm 1

303208101087 the ceramic plate temperature sensor 1

fixed board

IF-7017

541700100091

542300000059

Step1：

remove the screw A around the base cover

screw A

Step2：

remove the screw B

screw B

Step 3：

Step 4：

Remove C

Step 5：

Step 6

：

remove all the screws and wires

reserve the product

to remove the induction coil, straighten

the buckle of D

IF-7017

Step 7：

Step 8：

remove the display board

done

IF-7017

L2 L1

N2 N1

CN4

CN1

CN2

CN4

OUT4

OUT2

OUT1

OUT3

OUT4

OUT2

OUT1

OUT3

X1A

X2A

X3B

X3A

X11

FAN1

X10

NTC

Thermal

cut-out

Thermal cut-out

Thermal

cut-out

Thermal

cut-out

FAN

Induction

coil

Induction

coil

Induction coil

CN5

CN2

CN7

CN4

CN3

CN2

CN3

CN4

CN7

CN5

POWER IN

IF-7017

The induction hob is equipped with a self diagnostic function. With this test the technician is able to check the

function of several components without disassembling or dismounting the hob from the working surface.

Troubleshooting

1) failure code occur during customer using.

2) Solution a is as following.

3) If the problem can’t be settled by solution a, solution b can be used.

Failure code Problem Solution

E1/E2 Voltage irregularity. Unit should operate normally after a few

minutes and code will disappear from

display.

E3/E4 High temperature of ceramic plate Wait for temperature to return to normal.

Push “ON/OFF” button to restart unit.

Wait for temperature to return to normal.

Push “ON/OFF” button to restart unit.

E5/E6 High temperature of hob Check if the fan runs smoothly.Fan should

be replaced by a new one if not work

anymore.

F3/F4/F5/F6/F7/F8 Ceramic plate temperature sensor failure. Check the connection or replace the

ceramic plate temperature sensor.

F9/FA/FB/FC/FD/FE IGBT temperature sensor failure. Replace the power board.

Failure Problem Solution A Solution B

No power supplied. Check to see if plug is

secured tightly in outlet

and that outlet is working.

The accessorial power

board and the display

board connected failure

Check the connection.

The accessorial power

board is damaged. Replace the accessorial

power board

The LED does not

come on when unit is

plugged in.

The display board is

damaged. Replace the display

board.

Some buttons can’t work,

or the LED display is not

normal.

The display board is

damaged. Replace the display

board.

High temperature of the

hob. Ambient temperature

may be too high.Air

Intake or Air Vent may be

blocked.

There is something wrong

of the fan.

Check if the fan runs

smoothly.Fan should be

replaced by a new one if

not work anymore.

The Cooking Mode

Indicator comes on, but

heating does not start.

The power board is

damaged. Replace the power board.

for temperature to return

to normal.

Push “ON/OFF” button to

restart unit.

The power board and the

display board connected

failure;

Check the connection.

The display board of

communicate part is

damaged.

Replace the display

board.

Heating zones of the

same side ( Such as the

first and the second

zone ) would display “u” .

The power board is

damaged. Replace the power board.

Fan motor sounds

abnormal. The fan motor is

damaged. Replace the fan.

Pan Type is wrong.

Pot diameter is too small Use the proper pot (refer

to the instruction manual.)

Heating stops suddenly

during operation and

display “u”. Cooker has overheated; Unit is overheated.Wait

Pan detection circuit is

damaged, replace the

power board.

Failure Problem Solution A Solution B

Becken PLACA INDUCAO 4 ZONAS IF7017 Owner's manual

Becken PLACA INDUCAO 4 ZONAS IF7017 Owner's manual

Becken PLACA INDUCAO 4 ZONAS IF7017 Owner's manual

Other documents