FLASH F7100768 User manual

LED MOVING HEAD

19x15W BIG EYE

SERIES: DJ

User Manual

Art No F7100768

(ver.05.23)

EAN 5905358808481

21/35/78/97/112 CH

CONTENTS

INTRODUCTION 3

SAFETY INFORMATION 3

PRODUCT INFORMATION 4

INSTALLATION 4

CONNECTION 6

DMX CHART 8

PHOTOMETRICS 10

WARNING! The Led Moving Head (LMH) has a powerful pan and lt mo-

tor. The torque reacon when the head is panned suddenly can cause the

base to move if the xture is standing unsecured on a surface. Do not apply

power to the LMH unless the baase is securely fastened to a surface or to

rigging hardware.

WARNING! Use 2 clamps to rig the xture. Do not hang the xture from

only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners

are locked only when turned a full 900 clockwise.

WARNING! When clamping the xture to a truss or other structure at

any other angle than with the yoke hanging vercally downwards, use two

clamps of half-coupler type. Do not use any type of clamp that does not

completely encircle the structure when fastened.

WARNING! Posion or shade the head so that the front lens will not be

exposed to sunlight or any other strong light source from any angle - even

for a few seconds. See Figure 1. The LMH lens can focused the sun’s rays,

creang a potenal re hazard and causing damage.

IMPORTANT! Do not point strong light output from other xtures at the

LMH, as intense illuminaon can damaged the display.

Figure 1.

2

INTRODUCTION

SAFETY INFORMATION

THANK YOU FOR PURCHASING 19x15W BIG EYE. FOR SAFETY

REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CA-

REFULLY READ THE INSTRUCTIONS.

Please keep this User Manual

for future consultaon. If you sell

the xture to another user, be sure

that they also receive this instruc-

on booklet.

Unpack and check carefully the-

re is no transportaon damage be-

fore using the xture.

Before operang, ensure that

the voltage and frequency of po-

wer supply match the power

requirements of the xture.

It’s important to ground the

yellow/green conductor to earth

in order to avoid electric shock.

Disconnect main power before

servicing and maintenance.

Use safety chain when xes this

xture. Don’t handle the xture by

taking its head only, but always by

taking its base.

Maximum ambient temperature

is: 40°C Don’t operate it where the

temperature is higher than this.

In the event of serious ope-

rating problem, stop using the

fixture immediately. Never try

to repair the fixture by your-

self.

Repairs carried out by unskil-

led people can lead to damage

or malfunction. Please contact

the nearest authorized techni-

cal assistance center. Always

use the same type spare parts.

Do not connect the device

to any dimmer pack.

Do not touch any wire during

operation and there might be a

hazard of electric shock.

To prevent or reduce the risk

of electrical shock or fire, do

not expose the fixture to rain

or moisture.

The housing must be repla-

ced if they are visibly damaged.

Do not look directly at the li-

ght spot while the fixture is on.

3

In the latest version of this Head, the colors in the macro channel have been

improved, making them more natural and consistent with the paern. The co-

lors on the dimmers, power and parameters remain the same as in the previous

version (F7100547).

PRODUCT INFORMATION

INSTALATION

Light Source:

19 pcs x 15W 4in1 LEDs

Power consumpon: 300W

Power supply voltage:

110-245V, 50/60Hz AC

PAN range: 540°

TILT range: 270°

Beam angle (min/max): 4°-60°

Color: RGBW

Zoom: Yes

LED outline stripe eect

Operang modes: DMX 512,

Auto-running, Master/Salve,

Sound acve

DMX channel mode

21/35/78/78/97/112

IP Rang: IP65

Housing made: ABS

Integrated fastening hooks

Cooling: Acve

AC IN/OUT: PowerCon

3-Pin XLR DMX Input/Output

Net Weight: 14.4 kg

Weight with packaging:

59 kg (2x MH+Case)

Dimensions:

H(48)xW(40)xD(26) cm

Dim. (case):

H(59)xW(74)xD(46) cm

The unit should be mounted via its screw holes on the bracket. Always

ensure that the unit is rmly xed to avoid vibraon and slipping while

operang. Always ensure that the structure to which you are aaching

the unit is secure and is able to support a weight of 10 mes of the

unit’s weight. Also always use a safety cable that can hold 12 mes of

the weight of the unit when installing the xture. The equipment must

be xed by professionals. And it must be xed at a place where is out of

the touch of people and has no one pass by or under it.

The following item

are included inside the case:

4

❶ - Moving Head (2pcs)

❷ - powerCON cable (2pcs)

❸ - Omega clamp (4pcs)

❹ - User manual (1pc)

❺ - Transport Case

F7100767 [EAN 5905358808474]:

2x Moving Heads 19x15W Big Eye SET ver.05.23 + Case (SET)

AVAILABLE VERSIONS:

The following item

are included inside the box:

5

❶ - Moving Head (1pc)

❷ - powerCON cable (1pc)

❸ - Omega clamp (2pcs)

❹ - User manual (1pc)

❶

❷

❸

❹

❺

User

Manual

User

Manual

F7100768 [EAN 5905358808481]:

1x Moving Head 19x15W Big Eye SET ver.05.23 (carton package)

6

CONNECTION

The device is equipped with the following interfaces:

1. DMX (in/out): XLR 3(5)-pin socket

2. Power (in/out): powerCON socket

The connecon is performed using cable with

XLR-female -> XLR-Male plugs.

1

3

22

SHIELD

SIGNAL (+)

SIGNAL (-)

3

1

FEMALE

XLR

MALE

XLR

1

SHIELD

SIGNAL (+)

SIGNAL (-)

FEMALE

XLR

MALE

XLR

2

3

4

5

1

2

3

45

CAUTION! At the last xture, the

DMX signal has to be terminated

with a terminator. Solder a 120Ω

resistor between signal (-) and si-

gnal (+) into a XLR plug and plug

it in the DMX output of the last

xture.

3-PIN XLR

5-PIN XLR

Diagram of connecon of devices by DMX cable.

IMPORTANT! The maximum number of devices connected

in series via power cable is 6 pcs.

DMX

Controller DMX 512 DMX 512 120

Ω

Using lamp, the change rate of power voltage should be within ±10%,

if the voltage is too high, it will shorten the light’s life; if it’s not enough,

the lamp will be dark. Please restart it aer turning o light for 20 mi-

nutes unl full-cooling. Frequent switching will reduce the life span of

lamps and bulbs; intermient using will improve the life of bulbs and

lamps.

Input Voltage Frequency Total Power

100-245[V] AC 50/60[Hz] 300[W]

Voltage Specycaon.

7

The connecon is performed using power cable with powerCON

TRUE1 connector (included). The device must be operated by qualied

personnel.

CAUTION! In the case of cable damage do not aempt to repair. Repla-

cement or repair can be made only on the manufacturer or by a person

with appropriate permissions

8

DMX CHART

21 CH 35 CH

CHANNEL MODE

1Red

2Red ne

3 Green

4Green ne

5 Blue

6Blue ne

7 White

8White ne

9 Linear CTO

10 Macro colour

11 Strobe

12 Dimmer

13 Dimmer Fine

14 Pan

15 Pan Fine

16 Tilt

17 Tilt Fine

18 Funcon

19 Reset

20 Zoom

21 Zoom Rotaon

CHANNEL MODE

1Red

2Red ne

3 Green

4Green ne

5 Blue

6Blue ne

7 White

8White ne

9 Linear CTO

10 Macro colour

11 Strobe

12 Dimmer

13 Dimmer Fine

14 Pan

15 Pan Fine

16 Tilt

17 Tilt Fine

18 Funcon

19 Reset

20 Zoom

21 Zoom Rotaon

22 Shape Selecon

23 Shape Speed

24 Shape Fade

25 Shape R

26 Shape G

27 Shape B

28 Shape W

29 Shape Dimmer

30 Background Dimmer

31 Shape Transion

32 Shape Oset

33 Foreground Strobe

34 Background Strobe

35 Background Select

9

CHANNEL MODE

1 Red LED 1

2 Green LED 1

3 Blue LED 1

… Red LED …

… Green LED …

… Blue LED …

55 Red LED 19

56 Green LED 19

57 Blue LED 19

CHANNEL MODE

1 Red LED 1

2 Green LED 1

3 Blue LED 1

4 White LED 1

… Red LED …

… Green LED …

… Blue LED …

… White LED …

73 Red LED 19

74 Green LED 19

75 Blue LED 19

76 White LED 19

RGB RGBW

10

PHOTOMETRICS

Distance 1m:

26280,24 lx

6480 K

Ra 75

Measurements under laboratory

condions were made on

a spectrometer GL SPECTIS 1.0

R G B W

RGBW

11

FLASH-BUTRYM Sp.j.

Skarbimierzyce 18 · 72-002 Dołuje · POLAND

WWW.FLASH-BUTRYM.PL

FLASH F7100768 User manual

Related papers

Other documents