Hyundai 2021 Owner's manual

2021
Hyundai
Brand
Hyundai
Model
2021
Type
Owner's manual
Genuine Accessories
Electronic Installation Instructions
Glasses Gloves
Mask Hearing Protection
Part Weight (Gross) FMVSS 110 Compliance Information
1)
2)
2)
3)
4)
5)
6)
(C) Master Technician or Specialist
Notes to the installer:
Instructional Symbols / Definitions
Does NOT apply to models equipped with a Manual Transmission
Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a replacement, register the
removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old registration cannot be reused.
Application Notes
Center Punch
kg
lbs
0.16
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a
“Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced
carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
Hole Saw
26mm (1-1/32")
Extension
305mm (12")
Hole Saw
23mm (29/32")
Read the entire Installation Instructions prior to beginning the installation of this accessory.
Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.
Denotes important information to be
reviewed during the step
Wire Cutters
Pliers Ratchet
Electric Drill #2 Phillips
Screwdriver
10mm
Socket
Large
Drop Cloth Trim Removal Tool Torque WrenchDeburring Tool
0.35
(B) Dealer Technician
Denotes cautions to be taken to avoid
vehicle and component damage
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
Basic Required Tools
Denotes quality processes to be
checked prior to moving to the next step
Denotes personal protective equipment (PPEs)
that may be required for a step. Examples of
safety equipment icons noted below:
Denotes warnings that may lead to
serious physical injury or vehicle
damage
Denotes specific tools that are
necessary to complete a step
Specialty Required Tools
If this is aprinted copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning
installation. Use the latest revision date as noted by “Rev. Date” above.
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/abf55_ac000.pdf
N
O
T
E
Language
English
12/14/2023
Rev. Date
Accessory:ElantraVehicle Model:
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
( B )
Interior Light Kit
(A) Customer
Part No.
Model Year
Copy OEM Logo Here (→)
2021~
ABF55 AC000
Difficulty:
Note:
Drill Bit
3mm (1/8")
Revision Date
12/14/2023
Page 1 of 12
Genuine Accessories
No. No.
1 5
2 6
3 7
4
Hardware Overview
10 323
* Indicates extra components intentionally included in kit as spares.
Follow instructions for proper placement of each component.
Kit Overview
Module
Cable Tie*
Quick Reference Guide (QRG)
Description
Templates
A
Foam Pad*
B
1
Wiring Assembly
1
Switch
Foot Lamp
Description
Hardware Kit
2
1
Hardware Total
C
Plastic Retainer
D
T-Tap*
Qty
18
FM1
FM6
FM9
Radio Presets - record customer preset frequencies if disconnecting battery power
SAT1
SAT4
AM1
AM4
FM4
1
2
3
4
5
6
7
Revision Date
12/14/2023
Page 2 of 12
Genuine Accessories
Special Instructions
Revision Date
12/14/2023
Page 3 of 12
Genuine Accessories
A. Remove one (1) plastic retainer from the driver side center
console side panel and discard.
NOTE: Depending on the vehicle trim, the center portion of the plastic
retainer may or may not have a phillips screw.
Caution: Do not damage the center console side panel.
Ratchet and 10mm Socket
WARNING! Shock Hazard. Do not touch vehicle's negative battery
terminal to vehicle's positive battery terminal. Serious injury and
damage to the vehicle may occur.
A. Open hood.
Non-Hybrid Models Only
B. Remove negative (-) battery terminal cover, if applicable and
disconnect & isolate vehicle's negative (-) battery cable.
Hybrid Models Only
B. Disconnect and isolate the 12V Circuit Connector located on the
driver's side near the firewall between the engine and the brake fluid
reservoir as shown.
#2 Phillips Screwdriver or Trim Removal Tool
N
O
T
E
A. Engage the Parking Brake.
NOTE: The parking brake switch is located on the shifter lever trim panel
on vehicle's equipped with electronic parking brake.
B. Record any pre-set radio stations (if applicable). N
O
T
E
Caution: Make sure the parking brake is fully engaged.
N
O
T
E
2
N
O
T
E
A. Remove one (1) plastic retainer from the passenger side center
console side panel and discard.
NOTE: Depending on the vehicle trim, the center portion of the plastic
retainer may or may not have a phillips screw.
#2 Phillips Screwdriver or Trim Removal Tool
3
Caution: Do not damage the center console side panel.
4
1
Driver's Side Center Console Side Panel
Passenger's Side Center Console Side Panel
Non-Hybrid Models
Hybrid Models
Engine
Revision Date
12/14/2023
Page 4 of 12
Genuine Accessories
N
O
T
E
N
O
T
E
Caution: Do not damage the center console.
A. Remove the four (4) screws as shown from the center console.
B. Store the screws in a safe location for reinstallation.
Caution: Do not damage any vehicle components.
7
Trim Removal Tool
A. Carefully insert a trim removal tool between the shift lever boot and shift
pattern panel to disengage the boot clips from the shift pattern panel.
IMPORTANT: It is critical that the shift lever boot has disengaged from
the shift pattern panel before moving forward with this step. Use care not
to scratch or damage the shift lever boot or shift pattern panel.
B. Once the shift lever boot has disengaged from the shift pattern panel, pull
up on the shift lever knob to disengage the knob and boot from the
shifter lever shaft.
C. Place the shift lever knob and boot in a safe location for reinstallation.
D. Reach through the shift pattern panel opening, press and hold down the
shift lock release button and move the shift lever from Park (P) position
to Neutral (N) position.
A. Carefully dislodge the shift lever trim panel.
NOTE: Start dislodging form the rear center console armrest area.
B. Disconnect the two (2) connectors from the shift lever trim panel.
C. Remove the shift lever trim panel and store in a safe location for
reinstallation.
N
O
T
E
6
A. Lift open center console armrest.
B. Starting from the rear portion (near armrest), carefully dislodge
the side panel trim shown above.
C. Remove the one (1) screw as shown.
D. Place the side panel trim and screw in a safe location for reinstallation.
Trim Removal Tool and #2 Phillips Screwdriver
Caution: Do not damage the side trim panel.
8
N
O
T
E
Caution: Do not damage the shift lever trim panel, connectors or center
console.
#2 Phillips Screwdriver
Trim Removal Tool
5
Side Trim Panel
Shift Lever Trim Panel
Shift Pattern
Panel
Revision Date
12/14/2023
Page 5 of 12
Genuine Accessories
12
Ratchet, Extension, 10mm Socket and Trim Removal Tool
A. Carefully disengage the one (1) pressure clip on the driver's
side center console side panel as shown.
Caution: Do not damage any vehicle components.
A. Lift open the center console armrest and remove the felt pad.
B. Remove the two (2) bolts shown above.
C. Store the removed bolts and felt pad in a safe location for reinstallation.
11
Center Punch and Large Drop Cloth
N
O
T
E
N
O
T
E
Large Drop Cloth
910
N
O
T
E
Caution: Do not damage any vehicle components.
A. Ensure both center console side panels are placed on a drop
cloth to protect them from any scratches.
B. Remove the adhesive backing strips from the three (3) provided
templates and place them on the driver's and passenger's side
center console side panels as shown above.
NOTE: Place the templates flat on the panels. Do not fold over
the templates in places where the panel ends curve.
C. Using a Center Punch, mark the center of the three (3) crosshairs
as shown.
D. Remove the templates and discard.
Caution: Do not damage any vehicle components.
N
O
T
E
Caution: Do not damage any vehicle components.
A. Carefully separate the driver's and passenger's side center
console side panels from the rear portion of the center console
by lifting the rear portion of the center console and sliding it rearward.
B. Carefully disengage and remove the driver's and passenger's side center
console side panels from vehicle, move to a clean workbench and
place them on a large drop cloth to protect them from any scratches.
Driver's Side
Panel
Driver's Side
Panel
Passenger's
Side Panel
Driver's Side Panel
Passenger's Side Panel
Revision Date
12/14/2023
Page 6 of 12
Genuine Accessories
A. Check the inner of the driver's side center console side panel at the
Foot Lamp mark area for insulation pad and pull back insulation pad as
needed for the following Foot Lamp hole drilling procedure.
B. Drill a pilot hole at the Foot Lamp hole center punch mark using a 3mm
(1/8") Drill Bit.
C. Enlarge the pilot hole using a 26mm (1 1/32") Hole Saw.
D. Carefully Deburr the drilled hole. Do NOT enlarge the hole.
E. Repeat this step on the passenger's side center console side panel.
N
O
T
E
N
O
T
E
N
O
T
E
WARNING! Take precautions when using the drill to help avoid injury or
damage to the panels.
Electric Drill, Drill Bit 3mm (1/8"), Hole Saw 23mm (29/32") and
Deburring Tool
15
A. Check the inner of the driver's side center console side panel at the
Switch mark area for insulation pad and pull back insulation pad as
needed for the following Switch hole drilling procedure.
B. Drill a pilot hole at the Switch hole center punch mark using a 3mm
(1/8") Drill Bit.
C. Enlarge the pilot hole using a 23mm (29/32") Hole Saw.
D. Carefully Deburr the drilled hole. Do NOT enlarge the hole.
A. Install the Foot Lamps into both center console side panel holes with
connector facing rearwards towards the rear of the vehicle.
B. Install threaded Locknuts onto the backs of both Foot Lamps to secure
them in place. Do NOT over-tighten the Locknuts.
C. Install the Switch in the driver's side center console side panel with the
connector facing down.
D. Install threaded Locknut on the back of the Switch to secure it in place.
Do NOT over-tighten the Locknut.
N
O
T
E
Pliers
14
Electric Drill, Drill Bit 3mm (1/8"), Hole Saw 23mm (29/32"), Hole
Saw 26mm (1-1/32") and Deburring Tool
13
A. Using Pliers, remove the ribs located near the drilled holes on both side
panels to allow the Foot Lamps and Switch threaded Locknuts to sit flush
without interference.
WARNING! Take precautions when using the drill to help avoid injury or
damage to the panels.
16
Foot Lamps
26mm (1-1/32") Hole
Passenger's Foot Lamp Hole
Driver's Foot Lamp Hole
Switch Hole
Locknuts
Switch
23mm (29/32") Hole
Driver's Side Panel
Driver's Side Panel
Passenger's Side Panel
Revision Date
12/14/2023
Page 7 of 12
Genuine Accessories
N
O
T
E
A. Using up to four (4) Foam Pads, secure any loose areas of the insulation
pad on the driver's and passenger's side center console side panels, as
needed.
N
O
T
E
N
O
T
E
A. Carefully reengage the one (1) pressure clip on the driver's and passenger's
side center console side panels.
B. Pay attention to the C-Clip plastic retainers in the middle of the center
console and ensure they are secured onto the corresponding protruding
vehicle studs as shown.
A. Carefully reinstall the driver's and passenger's side center console
side panels back to the rear portion of the center console.
B. Carefully place the center console back into the vehicle and
connect the corresponding interior light kit harness connectors
into the interior light kit switch and foot lamps. Make sure all three (3)
connectors are locked in place.
N
O
T
E
19
Ensure the Switch and both Foot Lamp connectors are locked in place.
Caution: Do not damage any vehicle components.
A. Connect the provided Wiring Assembly into the ECU Module and
make sure it is locked in place.
B. Remove the adhesive backing liner from the ECU Module.
C. Adhere the ECU Module to the underside of the shifter housing with Wiring
Assembly facing forward as shown.
IMPORTANT: Ensure the ECU Module and Wiring Assembly does not
interfere with the shifter cable.
D. Secure the ECU Module with one (1) Cable Tie as shown.
E. Trim excess cable tie material.
F. Route the two (2) Foot Lamp harnesses forward towards the driver's and
passenger's foot wells.
Caution: Ensure the ECU Module and Wiring Assembly does not
interfere with the shifter cable.
20
17 18
Wire Cutters
Foam Pads
Front Lamp LH
Front Lamp RH
SWITCH
ECU Module
Cable Ties
Shifter Cable
Driver's Side
Panel
Shifter
Shifter Cable
C-Clips engaged
Revision Date
12/14/2023
Page 8 of 12
Genuine Accessories
21
Ensure connectors are locked in place.
Wire Cutters
IMPORTANT: For trims equipped WITHOUT Wireless Phone Charger, skip to step 22.
For trims equipped WITH Wireless Phone Charger, follow notes below and illustrations above.
A. Connect the male end of the Interior Light Kit T-Harness connector to the 36-Pin vehicle connector and wrap the connectors using one (1) Foam Pad.
B. Wrap one (1) Foam Pad around the two (2) male spade terminals as shown.
C. Route and bundle excess harnesses including the wrapped male spade terminals towards the front, driver's side and using one (1) cable tie, secure the harnesses to
the large vertical factory wire harness as shown.
D. Trim excess cable tie material.
N
O
T
E
Pliers and Wire Cutters
22
Ensure male spade connector is fully inserted into wire T-Tap. Check to see that the spade connector did not miss the slot. Check to see that it is not visible on
either side of female connector.
IMPORTANT: For trims equipped WITHOUT Wireless Phone Charger, follow notes below and illustrations above.
For trims equipped WITH Wireless Phone Charger, skip to step 23.
A. Identify the 16-Pin shift lever trim panel connector.
NOTE: The connector image above is the wire side view, NOT pin side view. Numbered in order from upper left to lower right.
B. Using a T-Tap, connect the RED wire of the Interior Light Kit Power Harness to the PINK or RED wire in Pin # 1 of the 16-Pin shift lever trim panel connector.
- Reference page 3, "T-Tap Installation Procedure," for detailed instructions.
C. Using a T-Tap, connect the BLACK wire of the Interior Light Kit Power Harness to the BLACK wire in Pin # 8 of the 16-Pin shift lever trim panel connector.
- Reference page 3, "T-Tap Installation Procedure," for detailed instructions.
D. Wrap one (1) Foam Pad around the power harness and the 16-Pin shift lever trim panel harness as shown.
E. Wrap two (2) Foam Pads around the two (2) Interior Light Kit T-Harness 36-Pin connectors as shown.
F. Route and bundle excess harnesses including the wrapped T-Harness towards the front, driver's side and using one (1) cable tie, secure the harnesses to the
large vertical factory wire harness as shown.
G. Trim excess cable tie material.
N
O
T
E
Interior Light Kit
Two Male Spade
Terminals
A
B
C
16-Pin Connector
Wire Side View
Interior Light Kit
T-Harness
(Not Used)
Wrapped Foam Pad
Wrapped Foam Pads
Foam Pad
Revision Date
12/14/2023
Page 9 of 12
Genuine Accessories
26
N
O
T
E
A. Reinstall the two (2) bolts and the Felt Pad under the Console Armrest.
B. Reinstall the six (4) screws securing the Center Console as shown.
N
O
T
E
A. Connect the harness connectors on the shift lever trim panel
B. For trims equipped WITH Wireless Phone Charger: Wrap one (1) Foam
Pad around the 36-Pin connectors.
C. Reinstall the shift lever trim panel.
Caution: Do not damage any vehicle components
Caution: Do not damage any vehicle components.
23 Ratchet, Extension, 10mm Socket and #2 Phillips Screwdriver 24
Caution: Do not damage any vehicle components.
N
O
T
E
A. Reinstall the one (1) screw as shown.
B. Carefully reinstall the side trim panel.
N
O
T
E
A. Install the provided plastic retainers on the driver's and passenger's side
center console side panels.
25 #2 Phillips Screwdriver
Caution: Do not damage any vehicle components.
Shift Lever Trim Panel
Side Trim Panel
Plastic
Retainers
Revision Date
12/14/2023
Page 10 of 12
Genuine Accessories
Item to be Checked
Press the Interior Light Switch again.
With the Ignition ON and Engine OFF, press the Interior Light Switch to turn
ON the Foot Lamps.
None of the Foot Lamps turn ON.
→ Check the connections of the ECU Module.
→ Check the connection of the Switch connector.
→ Check the connection of the T-Harness or T-Taps.
→ Check the 10A Fuse in the vehicle's illumination
circuit. Replace the fuse if blown.
One of the Foot Lamps does not turn ON.
Both Foot Lamps illuminate blue.
Function Check
Troubleshooting
Issue / Concern Items to be Checked
Result
Both Foot Lamps turn OFF.
→ Check the connection of the Foot Lamp connector that
doesn’t turn on.
→ Check the connection of the connector at the
ECU Module.
N
O
T
E
A. Reinstall the shift knob and boot.
B. Move the Shift Lever to Park (P) position.
N
O
T
E
Non-Hybrid Models Only
A. Reconnect the negative (-) battery cable, and torque to:
5.0 ~ 6.0 N.m (0.50 ~ 0.60 kgf.m, 45 ~ 52 lb-in).
B. Reinstall the negative (-) battery terminal cover, if applicable.
C. Close hood.
D. Perform Function Check.
E. Place the provided Quick Reference Guide into vehicle's glove box.
Hybrid Models Only
A. Reconnect the 12V Circuit Connector.
B. Close hood.
C. Perform Function Check.
D. Place the provided Quick Reference Guide into vehicle's glove box.
Caution: Do not damage any vehicle components.
WARNING! Shock Hazard. Do not touch vehicle's negative battery
terminal to vehicle's positive battery terminal. Serious injury and
damage to the vehicle may occur.
27 28
Ratchet, 10mm Socket and Torque Wrench
Non-Hybrid Models
Hybrid Models
Engine
Revision Date
12/14/2023
Page 11 of 12
Genuine Accessories
Block Diagram
Revision Date
12/14/2023
Page 12 of 12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Hyundai 2021 Owner's manual

2021
Hyundai
Brand
Hyundai
Model
2021
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents