Printing Notes:
Material: 5 MIL high gloss paper; 50# liner;with 1mil clear polyester
overlaminate (UV resistant)
Adhesive: V98 HCT adhesive.
Ink: Black
Printing: Offset Printing
Resolution: 150 DPI or above
Size: 11.69 x 8.27 in (A4) (W x H)
z
SHEET 1 OF 1
Wichita, Kansas USA 67219
The Coleman Company, Inc.
COMPOSITE- NO
CRITICAL DIMENSION
cm3
REV.
MATERIAL:
SEE NOTES
SEE NOTES
1:1
10-FEB-09
Black
Program: InDesign CS4
Rainy X
INSTRUCTION SHEET FOR 2000002974
ID
02
4010005157
SCALE:
NAME:
DATE: DRAWN BY: APPROVED BY: REVISION
FINISH
SPEC.:
DATE
NAME
ECN NO.
MODIFICATIONS
grams
g/cm3
This drawing contains proprietary information and trade secrets of The Coleman Company, Inc.
Unauthorized use or copying is prohibited.
METRIC
[INCH]
CHECKING IS COMPULSORY
VOLUME
01
02
10-FEB-09
29-NOV-11 Rainy X 20021139
NEW
1. Changed the dimension to A4(11.69 x 8.27 in (W x H)).
2. Changed the material to “5 MIL high gloss paper; 50# liner;with 1mil clear polyester
overlaminate (UV resistant)” and added “Adhesive: V98 HCT adhesive.”
3. Added the cover page and updated the copyright.
MASS
DENSITY
GENERAL TOLERANCES
EXCEPT AS NOTED
0 TO 6mm = ±0.1
>6 TO 30mm = ±0.2
>30 TO 80mm = ±0.3
>80 TO 180mm = ±0.4
>180mm = ±0.5
ANGULAR = ± 3°
PART
NO.:
DO NOT PRINT THIS PAGE
4010005157 (ECN20021139-02)
Your Pack-Away
®
Kitchen is now ready
to use and enjoy.
Fig. 18
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 12
Fig. 13
Fig. 1
Fig. 3
Fig. 11
Fig. 23
Fig. 24
Fig. 17
Fig. 19
Fig. 20
Fig. 21
Fig. 22
11. Lift up on hanger bracket and rotate
to position shown (Fig. 16 & 17).
Insert lantern bail.
12. On bottom side of tabletop,
push latches to lock in open
position. (Fig. 18)
13. Place tabletop onto braces and press down to lock into
clips on underneath side. (Fig. 19 & 20)
14. Insert posts of utensil rack, at a slight angle, to
lock into clips on back of table. (Fig. 21 & 22)
To Store
1. Reverse Set Up procedures.
2. Place components into carry case as shown. (Fig. 23)
3. Lock front latches on
carry case. (Fig. 24)
Your Pack-Away
®
Kitchen
is now ready to move or
place into storage.
To Set Up
1. Unlock front latches,
open carry case and
remove all components.
(Fig. 1)
2. Unhook supports from all 4 legs then open table frame
until fully extended. (Fig. 2, 3, & 4)
3. Rotate supports to positions shown. (Fig 5)
4. Position hole in bottom of each brace over pin
on support then push down to secure. (Fig. 6)
5. Attach net shelf by placing loops onto
hooks on legs as shown. (Fig. 7 & 8)
6. Assemble lantern hanger
pole by pressing down
on tab and inserting to a locked
position in the hole on other pole.
(Fig. 9, 10, & 11)
9. Tighten knob on
bracket to secure.
(Fig. 14)
7. Rotate bracket until it
lines up with tab then
push down to lock
position. (Fig. 12)
8. Insert assembled pole into bracket
(Fig. 13). NOTE: Arrow and notch
on pole must line up with notch in
bracket for proper installation.
10. Attach 2 grill
support braces
and adjust width
to properly
support your grill
shape & size.
Tighten all 4
knobs to secure.
(Fig. 15)
Fig. 15
WARNING:
Read instructions and warnings before set up and use.
1. Check to ensure product is not damaged, prior to use. If product is damaged, do not use.
2. Use care when setting up and taking down product to avoid pinch points.
3. Not for use by unsupervised children.
4. Never use on uneven or soft surface.
5. Weight limits for hanging items:
Spoon Rack – 1 lb. (454 g) Lantern Hook – 12 lbs. (5.4 Kg)
6. Table top not intended for grill use. Use grill support braces only.
PACK-AWAY
®
KITCHEN
WARNING: Do not over tighten. Over
tightening may damage aluminum frame.
Fig. 2
Fig. 4
Fig. 5
Fig. 6
Fig. 14
Fig. 16
The Coleman Company, Inc. • 3600 North Hydraulic • Wichita, Kansas 67219 U.S.A.
1-800-835-3278 in the United States • www.coleman.com
Sunbeam Corporation (Canada) Limited • DBA Jarden Consumer Solutions
20B Hereford Street • Brampton, ON L6Y 0M1
1-800-387-6161 in Canada • www.coleman.com
MADE IN CHINA
© 2011 The Coleman Company, Inc.
Coleman
®
, , and Pack-Away
®
are registered trademarks of
The Coleman Company, Inc.
Page is loading ...
/