For answers to your Monogram,
®
GE Profile
™
or
GE
®
appliance questions, visit our website at
ge.com or call GE Answer Center
®
service,
800.626.2000.
Specification Created 5/09
230131
Rear filler strip or backguard are available for
these ranges
Note: Door handle protrudes 3" from door face. Cabinets
and drawers on adjacent 45° and 90° walls should be
placed to avoid interference with the handle.
Note: Cabinets installed adjacent to slide-in
ranges must have an adhesion spec of at least
194° temperature rating.
Optional Kits for Slide-In Gas Ranges:
(Available at additional cost)
Lower/Side Trim Kits
JXS56BB - Lower Trim Kit (Black)
Accessory Backguards
JXS32SS - Brushed-Chrome Accessory Backguard
JXS37BB - Black Glass Accessory Backguard
Rear Filler Strip
WB07T10680 - Black Filler Strip Assembly
Installation Information: Before installing, consult
installation instructions packed with product for
current dimensional data.
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
Dimensions and Installation Information (in inches)
PGS908SEP
GE Profile
™
30" Slide-In Gas Range
28-1/4*
36
Maintain
at least 6"
from nearest
combustible
surface.
Acceptable
Electrical
Outlet Area
30" Slide-In Range
Dimensions (in inches)
45-1/8
2-1/4
5
6
4-1/2
30
30" Min.
15" Min.
6
30" Slide-in Elec. Range
Aug. 8, 2003 -km
23-3/16
30
30
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
25
*Wall to front of
closed door handle
on model JSP34.
28" on models
JSP26/JSS26/16.
Note: Range may be placed with 0" clearance (flush) at the back wall and side walls
below countertop if the range side trims above the countertop extend beyond the cabinet
fronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearest
combustible surface.
30
31-1/2
28-1/4*
36
Maintain
at least 6"
from nearest
combustible
surface.
Acceptable
Electrical
Outlet Area
30" Slide-In Range
Dimensions (in inches)
45-1/8
2-1/4
5
6
4-1/2
30
30" Min.
15" Min.
6
30" Slide-in Elec. Range
Aug. 8, 2003 -km
23-3/16
30
30
If you are NOT using the
Filler strip or Backguard:
If you are using the
Filler strip or Backguard:
25
*Wall to front of
closed door handle
on model JSP34.
28" on models
JSP26/JSS26/16.
Note: Range may be placed with 0" clearance (flush) at the back wall and side walls
below countertop if the range side trims above the countertop extend beyond the cabinet
fronts at least 1/4". (Self-clean models only.) Maintain at least 6" distance from nearest
combustible surface.
30
31-1/2
Counter Cutout Dimensions (in inches)
12
″
23-3/16
″
7
″
Accep
table
Gas Line
&
Electrical
Outlet Area
30″ Min.
30
″
M
in.
from
cooking
surface to bottom
of overhead
cabinets
Shave Rais
ed Edge
To Clear 31-1/8
″
Wid
e Control Panel
9
-1/2
″
Min.
From Walls
13
″
Max.
depth
For Optimum
Installation These
Surfaces Must
Be Flat & Level
Follow instructions
packaged with
alternate a
pp
l
iance
Counterto
p
Depth
25
″
(typical)
35-3/4
″
to 36-1/2
″
from floor to
countertop
18
″
Min. vertical
distance from the
bottom of the adjacent
overhead cabinets
1-1/4
″
Min. Counter top
to top of drawer
D r a wer
cord, p
lug,
receptacle box
3.5
″
to prev
ent
interferen
ce
& gas hookup
Max. depth of
with drawer
9/16
″
29-15/16
″
Min.
30-1/16
″
Max.
3
″
15
″
12
″
23-3/16
″
7
″
Accep
table
Gas Line
&
Electrical
Outlet Area
30″ Min.
30
″
M
in.
from
cooking
surface to bottom
of overhead
cabinets
Shave Rais
ed Edge
To Clear 31-1/8
″
Wid
e Control Panel
9
-1/2
″
Min.
From Walls
13
″
Max.
depth
For Optimum
Installation These
Surfaces Must
Be Flat & Level
Follow instructions
packaged with
alternate a
pp
l
iance
Counterto
p
Depth
25
″
(typical)
35-3/4
″
to 36-1/2
″
from floor to
countertop
18
″
Min. vertical
distance from the
bottom of the adjacent
overhead cabinets
1-1/4
″
Min. Counter top
to top of drawer
Dr awer
cord, p
lug,
receptacle box
3.5
″
to prev
ent
interferen
ce
& gas hookup
Max. depth of
with drawer
9/16
″
29-15/16
″
Min.
30-1/16
″
Max.
3
″
15
″