Installation Guide Smart-UPS
™
On-Line
Replacement Battery Module
APCRBC140/APCRBC140J
Safety Messages
Read the instructions carefully to become familiar with the equipment before trying to install, operate, service or
maintain it. The following special messages may appear throughout this manual or on the equipment to warn of
potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning safety label indicates that an electrical hazard exists
which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
Safety and General Information
Inspect the package contents upon receipt.
Notify the carrier and dealer if there is any damage.
• Adhere to all local and national electrical codes.
• Always recycle used batteries.
For information on recycling used battery modules, refer to the Battery Disposal Information sheet included
with the replacement battery module.
• Recycle the package materials or save them for reuse.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.
NOTICE
NOTICE used to address practices not related to physical injury. The safety alert symbol is not used with this signal word.
Smart-UPS On-Line APCRBC140/APCRBC140J2
Battery safety
• Before installing or replacing the batteries, remove jewelry such as wristwatches and rings.
High short circuit current through conductive materials could cause severe burns.
• Do not dispose of batteries by burning them. The batteries may explode.
• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.
Replace Battery Modules
Actual models may differ in appearance from those depicted in these graphics. Installation process is identical for all
models.
Note: The batteries will charge to 90% capacity in the first three hours of operation on utility power.
Do not expect full runtime capability during this initial charge period.
SRT5K/SRT6K/SRT5KXLJ UPS models
CAUTION
DAMAGE TO EQUIPMENT OR PERSONNEL
• The equipment is heavy. Each battery module weighs 17 kg (37 lb).
• Always practice safe lifting techniques adequate for the weight of the equipment.
• Adhere to all local and national electrical codes.
• Use the battery model handle to slide the battery modules in and out of the UPS and external battery pack (XLBP).
• Do not use the handle to lift or carry the battery module.
Failure to follow these instructions can result in equipment damage and minor or moderate injury.
UPS model RBC
SRT5KXLJ APCRBC140J
SRT5K/SRT6K APCRBC140
SRT8K/SRT10K
SRT5K USPS model
SRT5KXLJ UPS model
s
u
0
9
2
3
a
s
u
0
9
2
2
b
s
u
0
8
4
1
a
s
u
o
1
1
8
3
a
x4
Smart-UPS On-Line APCRBC140/APCRBC140J 3
SRT5K USPS model
SRT5KXLJ UPS model
s
u
0
8
4
2
a
s
u
0
8
4
3
a
s
u
0
8
4
4
a
s
u
0
9
2
3
b
s
u
0
8
4
4
b
s
u
0
8
4
3
b
s
u
0
8
4
2
b
s
u
0
8
4
1
b
s
u
o
1
1
8
3
b
x4
s
u
0
9
2
2
a
Smart-UPS On-Line APCRBC140/APCRBC140J4
SRT8K/SRT10K UPS models
s
u
0
9
2
3
a
s
u
o
0
7
7
9
c
s
u
o
0
7
7
8
b
x4
s
u
o
0
7
7
6
b
s
u
0
9
2
3
b
s
u
o
0
7
7
6
a
s
u
o
0
7
7
8
a
x4
s
u
o
0
7
7
9
d
x2 boxes
x4 battery modules
x2 boxes
x4 battery modules
Smart-UPS On-Line APCRBC140/APCRBC140J 5
External battery pack SRT192BP, SRT192RMBP, SRT192BPJ
s
u
0
9
2
3
a
s
u
0
9
2
9
a
s
u
0
9
1
6
a
x4
s
u
0
8
8
9
a
s
u
0
8
9
0
a
s
u
0
9
2
3
b
s
u
0
8
9
0
b
s
u
0
8
8
9
b
s
u
0
9
1
6
b
x4
s
u
0
9
2
9
b
x2 boxes
x4 battery modules
x2 boxes
x4 battery modules
Customer support and warranty information are available on the
APC by Schneider Electric web site, www.apc.com.
© 2016 APC by Schneider Electric. APC, the APC logo, Smart-UPS and PowerChute are owned
by Schneider Electric Industries S.A.S. or their affiliated companies. All other trademarks are
property of their respective owners.
EN 990-5181A-002
5/2016
RBC Installation Date
After RBCs are installed, the LCD shows a message to confirm if the installed RBCs are new. Select the correct option.
• Option Yes: The UPS sets the current date as the install date of the new RBCs.
• Option No: There is no change in the RBC install date.
When the replacement battery cartridge (RBC), is charged to full capacity, perform a Self Test and a Runtime
Calibration Test.
Check/modify the RBC install date
Use the UP/DOWN arrow buttons to navigate to the Config Menu > Battery > Installation Date.
POWER ON/OFF button
Load icon
Disable/mute audible alarm icon
UPS status information
Operation mode icons
ESCAPE button
OK button
UP/DOWN arrow buttons
Controllable outlet group status
icons
Battery status icons
su0870a
Output
230.0
v
On-Line
12 3
LOAD
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Schneider Electric 990-6522-003 Operating instructions
-
Chromalox PG442 User manual
-
RIDGID 18V Advanced Lithium Batteries and Charger User manual
-
American Power Conversion RS-232 User manual
-
Doran PC-400 Technical Manual
-
ParaBody 854 User manual
-
Doran Scales DS4100 User manual
-
ParaBody 473 User manual
-
Horizon Fitness Paragon III HRC Owner's manual
-
Life Fitness 873 User manual
