MULTIPLEX Automatiklader Dp 14 Owner's manual

MULTIPLEX
Brand
MULTIPLEX
Model
Automatiklader Dp 14
Type
Owner's manual

MULTIPLEX Automatiklader Dp 14

The MULTIPLEX Automatiklader Dp 14 is an automatic rapid charger for NiCd battery packs. It uses the Delta Peak method to detect a fully charged battery and automatically switches to a trickle charge when the rapid-charge process is complete. The charge current is supplied to the battery by a pulsing process and can be infinitely variable from 0.1A to 3A.

The charger is suitable for charging NiCd batteries with 4 to 14 cells and a capacity of 100 mAh to 2000 mAh. It has a compact design and is easy to use. Simply connect the charger to a 12 V DC power source, connect the battery to the output sockets, and press the START button. The charger will automatically select the appropriate charge current and start the charging process.

MULTIPLEX Automatiklader Dp 14

The MULTIPLEX Automatiklader Dp 14 is an automatic rapid charger for NiCd battery packs. It uses the Delta Peak method to detect a fully charged battery and automatically switches to a trickle charge when the rapid-charge process is complete. The charge current is supplied to the battery by a pulsing process and can be infinitely variable from 0.1A to 3A.

The charger is suitable for charging NiCd batteries with 4 to 14 cells and a capacity of 100 mAh to 2000 mAh. It has a compact design and is easy to use. Simply connect the charger to a 12 V DC power source, connect the battery to the output sockets, and press the START button. The charger will automatically select the appropriate charge current and start the charging process.

F
EATURES
The DP 14 charger is an automatic rapid-charger for
NiCd battery packs. The charge current is supplied to the
battery by a pulsing process. The charger uses the Delta
Peak method to detect a fully charged battery. At the end
of the rapid-charge process the unit switches automatically
to a trickle charge, and the current then falls to about 5%
of the rapid-charge current previously selected. Please
note that it is not allowed to leave the NiCd pack in a
trickle charge process for more than one hour.
S
PECIFICATION
Input
l Voltage: 12 V DC - car battery
l Fuse: 15 A fuse
Output
l No. of cells: 4 to 14 NiCd cells
l Cell capacity: 100 mAh to 2000 mAh
l Output current: 0.1A to 3A, infinitely variable
l Dimensions: 150 x 102 x 40 mm
l Weight: 600 g
U
SING
THE
CHARGER
1.Connect the charger to the power source.
Check polarity carefully!
The LED (SCHNELL/ERHALTUNG - RAPID/TRICKLE)
will glow green, and you will hear an audible warning
signal. Press the OFF button to switch off the warning
tone if you wish.
2. Rotate the current selector knob anti-clockwise
as far as it will go.
This selects the minimum charge current.
3. Connect the NiCd battery to the output sockets.
Check polarity!
l RED = POSITIVE (+)
l BLACK = NEGATIVE (-)
4.Start the charge process.
Press the START button.
The LED (SCHNELL/ERHALTUNG) glows red.
5.Set the charge current.
You can now rotate the current selector knob to set a
charge current which is suitable for the battery
connected to the unit. Follow the battery manufacturer’s
recommendations here.
modelltechnik gmbh
,
Neuer Weg 15, D-75 223 NIEFERN
Automatik-Lader DP14 Nr. 82 57 25
As a guide we recommend 2 x C for rapid-charge
MULTIPLEX batteries, where C = nominal capacity.
Charge capacity in A = Capacity of the battery x 2.
When the charge process is complete, the unit switches
to a trickle charge. The LED then switches back to
green and the audible warning signal sounds again.
6.Disconnect the power source, charger and
NiCd pack when you have finished
charging.
S
AFETY
MEASURES
This charger may only be used with rapid-charge
type batteries.
Never attempt to charge your batteries at an
excessive rate.
NiCd packs can explode if the charge current is too
high.
Do not stand the unit on a heat-sensitive surface
for charging.
The case gets quite warm during the charge process,
and this could damage the surface beneath.
From time to time check the battery temperature
by hand while it is being charged.
At the end of the charge process the pack will heat up
to about 40 degrees C.
Be sure to disconnect power source, charger
and NiCd pack when the charge process is over.
The trickle charge is too high to allow you to leave
batteries connected to the charger permanently - max.
1 hour!
DP 14 automatic charger
Order No. 9 2517
Operating instructions
  • Page 1 1

MULTIPLEX Automatiklader Dp 14 Owner's manual

MULTIPLEX
Brand
MULTIPLEX
Model
Automatiklader Dp 14
Type
Owner's manual

MULTIPLEX Automatiklader Dp 14

The MULTIPLEX Automatiklader Dp 14 is an automatic rapid charger for NiCd battery packs. It uses the Delta Peak method to detect a fully charged battery and automatically switches to a trickle charge when the rapid-charge process is complete. The charge current is supplied to the battery by a pulsing process and can be infinitely variable from 0.1A to 3A.

The charger is suitable for charging NiCd batteries with 4 to 14 cells and a capacity of 100 mAh to 2000 mAh. It has a compact design and is easy to use. Simply connect the charger to a 12 V DC power source, connect the battery to the output sockets, and press the START button. The charger will automatically select the appropriate charge current and start the charging process.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents