Invacare 1488 User manual

Invacare
Brand
Invacare
Model
1488
Type
User manual

This manual is also suitable for

Invacare 1488 offers a secure and convenient way to mount oxygen cylinders onto your wheelchair. Its adjustable bracket accommodates various cylinder sizes and the long adjustment knob ensures a snug fit. The O2 Holder Accessory Kit is easy to install and compatible with wheelchairs featuring 7/8-inch diameter tubing. Remember to follow the oxygen cylinder manufacturer's guidelines for proper usage.

Invacare 1488 offers a secure and convenient way to mount oxygen cylinders onto your wheelchair. Its adjustable bracket accommodates various cylinder sizes and the long adjustment knob ensures a snug fit. The O2 Holder Accessory Kit is easy to install and compatible with wheelchairs featuring 7/8-inch diameter tubing. Remember to follow the oxygen cylinder manufacturer's guidelines for proper usage.

SAFETY SUMMARY
The following recommendations are made for the
safe installation of the O2 Holder Accessory Kit:
2. Push the bracket of the O2 cylinder holder over
the rear upright of the wheelchair and secure in
place with the hex screw, spacer and locknut.
3. Install plug button on top of O2 cylinder holder.
4. Use the long adjustment knob on the O2 cylinder
holder bracket to secure the oxygen cylinder in
place.
Spacer
Plug Button
Rear Step
Tube
Rear
Upright
Long
Adjustment
Knob
Long Tube
Guide Insert
Short
Tube
Guide
Insert
Locknut
Hex
Screw
FIGURE 1 - INSTALLING O2 CYLINDER HOLDER
Bracket
O2 Cylinder
Holder
WARNING
DO NOT assemble or use this equipment without
first reading and understanding this
instruction sheet. If you are unable to understand
the warnings, cautions or instructions, contact a
healthcare professional, dealer or technical per-
sonnel before attempting to install this equipment
- otherwise, injury or damage may occur.
Check ALL parts for shipping damage. If
shipping damage is noted, DO NOT use. Contact
Carrier/Dealer for further instructions.
Ensure that ALL attaching hardware is securely
assembled to the wheelchair before operating
the chair with the O2 Cylinder Holder Accessory
Kit.
Follow the Oxygen Cylinder manufacturers guide-
lines for proper usage of the oxygen cylinder.
INSTALLING O2 CYLINDER HOLDER
(FIGURE 1)
NOTE: If rear step tube is 7/8-inch diameter
tubing, install the long tube guide insert into the
rear step tube before installing the O2 cylinder
holder.
1. Place the O2 cylinder holder and slide it onto the
rear step tube of the wheelchair.
NOTE: IF rear upright tubing is 7/8-inch diameter
tubing, install the short tube guide insert over the
rear upright before installing and securing the O2
cylinder holder bracket.
O2 Cylinder Holder Accessory Kit
Assembly, Installation and Operating Instructions
Model Nos. 1488, 1497 and T1497
Invacare Corporation www.invacare.com
USA Canada
One Invacare Way 5970 Chedworth Way Invacare
®
and Yes, you can. are trademarks of Invacare
Elyria, Ohio USA Mississauga, Ontario Corporation.
44036-2125 L5R 3T9, Canada © 2000 Invacare Corporation
800-333-6900 905-890-8838 Form No. 91-200 Part No. 1027930 Rev E (2) 12/00
  • Page 1 1

Invacare 1488 User manual

Invacare
Brand
Invacare
Model
1488
Type
User manual
This manual is also suitable for

Invacare 1488 offers a secure and convenient way to mount oxygen cylinders onto your wheelchair. Its adjustable bracket accommodates various cylinder sizes and the long adjustment knob ensures a snug fit. The O2 Holder Accessory Kit is easy to install and compatible with wheelchairs featuring 7/8-inch diameter tubing. Remember to follow the oxygen cylinder manufacturer's guidelines for proper usage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers