Apple SpeedTouch ST546 v6 Owner's manual

SpeedTouch™546(v6)

Residential ADSL Gateway

User’s Guide

Power

DSL

Ethernet

Internet

SpeedTouch™

546

(v6)

User’s Guide

Copyright

Distribution and copying of this document, use and communication of its contents is not permitted without written authorization

from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice,

and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or

inaccuracies that may appear in this document.

Thomson Telecom Belgium

Prins Boudewijnlaan, 47

B-2650 Edegem

Belgium

www.speedtouch.com

Trademarks

The following trademarks are used in this document:

 SpeedTouch™ is a trademark of THOMSON.

 Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.

 Ethernet™ is a trademark of Xerox Corporation.

 Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Alli-

ance", their respective logos and "Wi-Fi Protected Access" are trademarks of the Wi-Fi Alliance.

 UPnP™ is a certification mark of the UPnP™ Implementers Corporation.

 Microsoft®, MS-DOS®, Windows® and Windows NT® are either registered trademarks or trademarks of Microsoft Corpo-

ration in the United States and/or other countries.

 Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and

other countries.

 UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.

 Adobe®, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incor-

porated, registered in the United States and/or other countries.

 Netscape® and Netscape Navigator® are registered trademarks of Netscape Communications Corporation.

Other brands and product names may be trademarks or registered trademarks of their respective holders.

Document Information

Status: v1.0 (January 2006)

Reference: E-DOC-CTC-20051017-0144

Short Title: User’s Guide ST546

(v6) R5.4

Contents

E-DOC-CTC-20051017-0144 v1.0

i

Contents

About this User’s Guide .............................................. 1

1 Getting to know your SpeedTouch™ ......................... 3

1.1 SpeedTouch™ LED Behaviour ........................................................ 4

1.2 Accessing your SpeedTouch™ ....................................................... 5

1.2.1 Access via the Web Interface .......................................................................................... 6

1.2.2 Access via CLI................................................................................................................... 7

1.2.3 Access via FTP.................................................................................................................. 9

1.2.4 Remote Assistance ........................................................................................................ 12

2 Local Network Setup .................................................. 13

3 Internet Connectivity Dial-In Clients ......................... 15

3.1 SpeedTouch™ Web Pages ............................................................ 17

3.2 Internet Gateway Device Control Agent ...................................... 19

4 SpeedTouch™ Web Interface .................................... 21

4.1 Navigation.................................................................................... 22

4.1.1 Menu............................................................................................................................... 23

4.1.2 Language Bar ................................................................................................................. 24

4.1.3 Navigation Bar ............................................................................................................... 25

4.1.4 Notification Area ............................................................................................................ 26

4.1.5 Tasks ............................................................................................................................... 27

Contents

E-DOC-CTC-20051017-0144 v1.0

ii

4.2 Home ............................................................................................ 28

4.3 SpeedTouch ................................................................................. 29

4.3.1 Information..................................................................................................................... 30

4.3.2 SpeedTouch™ Easy Setup............................................................................................ 31

4.3.3 Restart............................................................................................................................. 32

4.3.4 Configuration ................................................................................................................. 33

4.3.5 Back up & Restore..........................................................................................................34

4.3.6 Reset to Factory Defaults .............................................................................................. 35

4.3.7 Event Logs ...................................................................................................................... 36

4.4 Broadband Connection................................................................. 37

4.4.1 Connectivity Check ........................................................................................................ 38

4.4.2 DSL Connection .............................................................................................................39

4.4.3 Internet Services ............................................................................................................ 40

4.4.4 Internet Service Settings............................................................................................... 41

4.5 Toolbox ........................................................................................ 42

4.5.1 Remote Assistance ........................................................................................................ 43

4.5.2 Game & Application Sharing ........................................................................................ 44

4.5.3 Defined Games & Applications..................................................................................... 46

4.5.4 Game or Application Definition.................................................................................... 47

4.5.5 New Game or Application............................................................................................. 48

4.5.6 Parental Control ............................................................................................................. 49

4.5.7 Web Filtering Activation................................................................................................52

4.5.8 Content Level ................................................................................................................. 53

4.5.9 New Content Level......................................................................................................... 54

4.5.10 Firewall ........................................................................................................................... 56

4.5.11 Intrusion Detection ........................................................................................................ 59

4.5.12 Dynamic DNS ................................................................................................................. 60

4.5.13 User Management ......................................................................................................... 61

4.5.14 Edit User ......................................................................................................................... 63

4.5.15 Change Default User......................................................................................................64

4.5.16 Add User......................................................................................................................... 65

4.6 Home Network ............................................................................. 66

4.6.1 Devices............................................................................................................................ 68

4.6.2 Device Settings .............................................................................................................. 69

4.6.3 Assign Public IP.............................................................................................................. 71

4.6.4 Interfaces ........................................................................................................................ 72

4.6.5 Interface Settings ........................................................................................................... 73

4.6.6 DHCP Pool ...................................................................................................................... 74

Contents

E-DOC-CTC-20051017-0144 v1.0

iii

5 Troubleshooting.......................................................... 77

5.1 General SpeedTouch™ Troubleshooting ...................................... 78

5.1.1 Ethernet Troubleshooting ............................................................................................. 79

5.2 UPnP™ on Windows XP Systems................................................. 80

5.3 Reset to Factory Defaults ............................................................ 82

Contents

E-DOC-CTC-20051017-0144 v1.0

iv

About this User’s Guide

1

E-DOC-CTC-20051017-0144 v1.0

About this User’s Guide

Used symbols The following symbols are used in this User’s Guide:

Terminology Generally, the SpeedTouch™546(v6)(i) will be referred to as SpeedTouch™ in this

User’s Guide.

Documentation and

software updates

THOMSON continuously develops new solutions, but is also committed to improve

its existing products.

For suggestions regarding this document, please contact

documentation.spe[email protected]

.

For more information on THOMSON's latest technological innovations, documents

and software releases, visit us at: w

ww.speedtouch.com.

A note provides additional information about a topic.

A tip provides an alternative method or shortcut to perform an action.

!

A caution warns you about potential problems or specific precautions that

need to be taken.

About this User’s Guide

2

E-DOC-CTC-20051017-0144 v1.0

3

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

1 Getting to know your SpeedTouch™

Introduction With the SpeedTouch™546(v6)(i) Residential ADSL Gateway you can build a secure

home or small office network, connecting Ethernet devices and surf the Internet at

high speed.

Installation For more information on how to set up, install and wire your SpeedTouch™ and set

up Internet connection, refer to the Installation and Setup Guide.

Configuration This User’s Guide will help you configuring your SpeedTouch™.

Before you begin Before connecting the SpeedTouch™, please read the SpeedTouch™ Quick

Installation Guide and the Safety Instructions and Regulatory Notices.

4

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

1.1 SpeedTouch™ LED Behaviour

Front panel LEDs The SpeedTouch™ is equipped with a number of LEDs on its front panel, indicating

the state of the device during normal operation.

The following table shows the meaning of the different LEDs.

Indicator Description

Name Colour State

Power Green Solid on Power on, normal operation

Red Solid on Power on, self-test failed, indicating

device malfunction

Orange Solid on Bootloader active

Off Power off

Ethernet Green Blinking Ethernet activity

Solid on Ethernet connection, no activity

Off No Ethernet connection

DSL Green Blinking Pending DSL line synchronisation

Solid on DSL line synchronised

Off No DSL line

Internet Green Blinking Internet activity

Solid on Internet connectivity, no activity

Red Solid on Internet connection setup failed

Off No Internet connection

POWER

DSL

ETHERNET

INTERNET

5

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

1.2 Accessing your SpeedTouch™

Access methods Your SpeedTouch™ is accessible in one of the following ways:

Access Method Can be used to

Web browser Configure your SpeedTouch™ via HTTP or

HTTPS.

For more information, see “1.2.1 Access via

the Web Interface” on page 6.

Command Line Interface (CLI) Fine-tune your SpeedTouch™ configuration.

For more information, see “1.2.2 Access via

CLI” on page 7.

File Transfer Protocol (FTP) Back up and restore data on your

SpeedTouch™.

For more information, see “1.2.3 Access via

FTP” on page 9.

Remote Assistance Allow a remote user to help you configuring

your SpeedTouch™.

For more information, see “1.2.4 Remote

Assistance” on page 12.

6

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

1.2.1 Access via the Web Interface

To access the

SpeedTouch™ via the

Web interface

Proceed as follows:

1 Open a Web browser.

2 In the address bar, type your SpeedTouch™’s IP address or DNS host name

(h

ttp://speedtouch.lan or 192.168.1.254 by default)

The SpeedTouch™ Home page appears, from where you can navigate to all

the configurable aspects of the SpeedTouch™.

For more information on the Web pages, see “4 SpeedTouch™ Web Interface” on

page 21.

You can access the pages via HTTP or HTTPS.

For remote assistance the secure version HTTPS is used in

combination with certificates. Simply provide your ISP with the link as

shown, user name and password before he can log on to the pages.

For more information, see “1.2.4 Remote Assistance” on page 12.

7

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

1.2.2 Access via CLI

To access the

SpeedTouch™ via the

Command Line

Interface (CLI)

You can access the Command Line Interface (CLI) via:

 A Telnet session

This requires a TCP/IP connection between the host from which the Telnet

session is opened and the SpeedTouch™. Your SpeedTouch™ and the

connected computer must have an IP address in the same subnet.

 Quote site commands (over FTP)

For more information, see “ Quote site command” on page 11.

For more information on CLI commands, see the SpeedTouch™ CLI Reference

Guide.

8

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

To start a Telnet

session

Proceed as follows:

1 Open a telnet application.

2 Connect to your SpeedTouch™.

3 Enter your SpeedTouch™ security user name and password.

As soon as you have opened a session to the CLI, the SpeedTouch™ banner is

displayed, followed by the CLI prompt, as shown in the example below.

You can use the Command Prompt window.

In Microsoft Windows XP for instance:

1 On the Windows taskbar, click Start.

2 Select (All) Programs > Accessories > Command Prompt

.

In the Command Prompt window:

At the prompt, type

telnet followed by the IP address of your

SpeedTouch™ (192.168.1.254 by default).

The default user is ‘Administrator’ and the default password is blank.

Username : Administrator

-----------------------------------------------------------------------

-

* ______ SpeedTouch

* ___/_____/\

* / /\\ Version 5.4

* _____/__ / \\

* // / \ /\ \ THOMSON

* _______//_______/ \ / _\/______

* / /\ \ / // /\

* __/ / \ \ / / / / _\__

* / / / \_______\/ / / / / /\

* /_/______/___________________/ /________/ /___/ \

* \ \ \ ___________ \ \ \ \ \ /

* \_\ \ / /\ \ \ \ \___\/

* \ \/ /\ \\ \/

* \_____/ / \ \ \________\/

* /__________/ \ \ /

* \ _____ \ /_____\/

* \ / /\ \ /___\/

* /____/\\/

* \ \ /___\/

* \____\/

-----------------------------------------------------------------------

{Administrator}=>

9

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

1.2.3 Access via FTP

To access the

SpeedTouch™ via the

File Transfer Protocol

(FTP)

You can access the file system of the SpeedTouch™ via the File Transfer Protocol

(FTP), in order to:

 Restore or back up configuration files, templates or language packs.

 Upgrade your configuration.

File system The SpeedTouch™ file system is stored on non-volatile memory and contains the

SpeedTouch™ software, service template files and (optionally) default setting files.

To open an FTP session Proceed as follows:

1 Open a Command Prompt window.

2 At the prompt, type ftp followed by the IP address of your SpeedTouch™

(192.168.1.254 by default).

3 Enter your SpeedTouch™ security user name and password.

The example below shows an FTP session to the SpeedTouch™ file system.

File system structure The structure of the file system is very simple: it consists of a single root directory

called root and a subdirectory called dl (download).

 The root directory contains:

 all the necessary files for the SpeedTouch™ to start correctly

 the dl directory

 The dl directory contains the software image.

In Microsoft Windows XP for instance:

1 On the Windows taskbar, click Start.

2 Select

(

All) Programs > Accessories > Command Prompt

.

The default user is ‘Administrator’ and the default password is blank.

If you made changes to the SpeedTouch™ configuration and saved

them, a user.ini configuration settings file is created in the dl

subdirectory.

10

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

File system access

rights

In the different directories you have the following rights:

Common FTP

commands

Depending on the access rights you have in a directory, you can use one of the

following commands:

Directory Access rights

root NO read/write

dl read/write

Use the

command ...

to ...

cd access another directory than the one currently open.

Example: ftp>cd dl.

dir list the directory files.

Example: ftp>dir.

bin set the transfer mode to ‘binary’.

hash turn on the hashing option.

put upload files.

Example: ftp>put C:/MyBackupFiles/user.ini.

A configuration file must be uploaded to the dl directory.

get download files.

Example: ftp>get user.ini.

Downloading the configuration file must be done from the dl

directory.

delete delete files.

bye quit FTP.

11

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

FTP file transfer To allow correct file transfers, set the transfer mode to “binary”: at the ftp prompt,

type

bin and press ENTER.

Example.

Quote site command All the CLI commands can be executed from within an FTP session. Only complete

CLI commands (in other words, the complete command syntax with all the

parameters already specified) can be executed.

Example: To execute the CLI command

:ip iplist to list all IP addresses

currently assigned to SpeedTouch™ interfaces, at the FTP prompt, type ‘quote site

ip iplist’ and press ENTER.

For more information on CLI commands, see the SpeedTouch™ CLI Reference

Guide.

Turn on the hashing option to see the progression of the file transfer: At the

ftp prompt, type

hash and press ENTER.

/home/doejohn{1}$ftp 192.168.1.254

Connected to 192.168.1.254

220 Inactivity timer = 120 seconds. Use 'site idle <secs>' to change.

Name (192.168.1.254:doejohn):

331 SpeedTouch™ (00-90-D0-01-02-03) User 'doejohn' OK. Password requir

ed.

Password : ######

330 OK

ftp>

ftp>bin

200 TYPE is now 8-bit binary

ftp>

ftp>hash

200Hash mark printing on (8192 bytes/hash mark).

ftp>cd dl

250 Changed to /dl

ftp>put C:\user.ini

200 Connected to 192.168.1.10 port 1271

150 Opening data connection for user.ini

226 File written successfully

ftp: 256 bytes sent in 0,000Seconds 256000,000Kbytes/sec.

ftp>

ftp> quote site ip iplist

200- Interface Type IP-address Point-to-point/Mask

200- 2 LocalNetwork Ethernet 10.0.0.138 255.255.255.0

200- 2 LocalNetwork Ethernet *192.168.1.254 255.255.255.0

200- 1 Internet Serial 81.240.198.191 81.240.198.1

200- 0 loop Internal 127.0.0.1 255.255.255.255

200-

200 CLI command "ip iplist" executed

ftp>

12

E-DOC-CTC-20051017-0144 v1.0

Chapter 1

Getting to know your SpeedTouch™

1.2.4 Remote Assistance

To access the

SpeedTouch™ remotely

You can make your SpeedTouch accessible from the Internet with regard to remote

support. In this way, you can allow your help desk to access your SpeedTouch™

remotely.

To enable remote

access

Proceed as follows:

1 Go to the SpeedTouch™ pages, as described in “1.2.1 Access via the Web

Interface” on page 6.

2 In the menu, select Toolbox > Remote Assistance.

3 Click Enable Remote Assistance.

4 Provide the following parameters to your help desk:

 URL (the HTTPS link)

 User name

 Password

Your ISP is now able to access your SpeedTouch™ via the HTTPS link in

combination with the provided certificate (a secure authentication

mechanism).

To disable remote

access

Proceed as follows:

1 Go to the SpeedTouch™ pages, as described in “1.2.1 Access via the Web

Interface” on page 6.

2 In the menu, select Toolbox > Remote Assistance.

3 Click Disable Remote Assistance.

For security reasons, remote assistance will be automatically disabled after

20 minutes of inactivity, or after restarting your SpeedTouch™.

Page is loading ...

Apple SpeedTouch ST546 v6 Owner's manual

This manual is also suitable for

Apple SpeedTouch ST546 v6 Owner's manual

Related papers

Other documents